1998-2013 H-D Street Glide Stage-3 Installation

[@donaldstrickland9951]

As always Rockford Fosgate is the best...

[@rockfordfosgate]

Thanks Donald for hanging in there with your install!

[@KeithR1250]

I own this complete kit! I had a few bad experiences with the R.F. dealer/installer! Few hiccups. After talking with a Rockford Fosgate Representative, they sweetened the deal! The only thing I don't like is that blue tooth and Pandora can take like 45 seconds to a minute to pair with your phone. And other times it pairs in about 15 seconds. You will also have to set up your own equalizer to get the good sound.

[@rockfordfosgate]

Thanks for your feedback Keith, we actually released Preset Tunes that you can load for the best sound. Download our new Tuning Guide and select the configuration for your motorcycle. It shows how to access these Rockford Fosgate configured Tunes: rftech.custhelp.com/app/answers/detail/a_id/1355. As we improve the software, we'll be publishing updates here: rftech.custhelp.com/app/answers/detail/a_id/1358

[@rockfordfosgate]

Thanks for your feedback. Sorry you had issues with the dealer, but glad that the rep stepped in to get everything straightened out. If you're using Android, we have experienced our own issues regarding Bluetooth connectivity (it happens on other products, not just the PMX source unit). We have found that iOS devices have very reliable connectivity.

[@donaldstrickland9951]

Just bought this complete kit is there any additionals that I need? Want?

[@rockfordfosgate]

Thank You Donald! My only recommendation would be an USB extension that would allow you to play all your music from a jump drive. Otherwise, everything is included in the kit. -Eric

[@donaldstrickland9951]

Thanks, if I have any problems ill hit you back...

[@rockfordfosgate]

@@donaldstrickland9951 Sounds great, brother. Good luck on the install. One piece of advice ... pull the old radio out and install the new one at an angle, it's easier to slide against the metal bracket while at an angle instead of straight in/out.

[@donaldstrickland9951]

Hey on the clutch side the power and ground for the amp there is no existing harness to zip tie too?

[@rockfordfosgate]

You can attach the Power harness to anything relevant. You just want to make sure the harness plug isn't stressed when moving the handlebars.

[@donaldstrickland9951]

@@rockfordfosgate there is nothing on the clutch side relevant. I ran it from front fairing down to battery and zip tied it to wiring harness, does it have to be on clutch side?

[@rockfordfosgate]

@@donaldstrickland9951 You’re fine, it doesn’t have to on that side, you just need to spread everything out to get the center trough back on because it’s tight. This is why we suggest laying the harness on one side, and the power harness on the opposite side.

[@rich1184]

Nice set up

[@rockfordfosgate]

Great! Thanks for your feedback!

[@donaldstrickland9951]

Fuel equalizer hose? Is that just a crossover line?

[@rockfordfosgate]

Yes it is.

[@donaldstrickland9951]

So drain the tank from here? I got a stainless braided line from drag specialties...

[@rockfordfosgate]

@@donaldstrickland9951 Yes, we recommend draining the tank so it's easier to remove and run the harnesses underneath.

[@1246kenny]

At 10:35 you plugged the 35 pin connector to the input side of the amp. Then ran the bag lid harness which has an input harness. Do I use the y adapter here because I’m out of input plugs?

[@rockfordfosgate]

Hi 1246kenny, at 10:35 I'm connecting the 35-pin radio connector to the Amp's REAR INPUT. At 10:44 I'm connecting the bag-lid speaker harness to the Amp's REAR OUTPUT. Therefore, each input & output should only have one MOLEX connected. There should be no need for a Y-Adaptor unless your running LOWERS or TOURPAK.

[@1246kenny]

Awesome thank you for the quick reply

[@rockfordfosgate]

@@1246kenny You're welcome. I know the videos don't zoom-in too close, so I'm always happy to help out.

[@donaldstrickland9951]

So the cut outs do not align properly with my bags, i have after market stretched bags, 4.5"?

[@rockfordfosgate]

OHHH SNAP! Those bag-lid kits are for Harley-Davidson hard-shell bags only.

[@donaldstrickland9951]

They are hard bags but there 14 and up lids, the tops not even close and the bottom mount doesnt fit at all.

[@donaldstrickland9951]

@@rockfordfosgate Does rockford sell a kit 14 and up street glide that just has cut out template, mounting plate, and speaker grills? Please say yes???

[@rockfordfosgate]

@@donaldstrickland9951 The kit in the 1998-2013 Stage-3 are designed for the older bag-lid style. So, since you upgraded the bags to 2014+ bag-lids, that kit will not work.

[@rockfordfosgate]

@@donaldstrickland9951 I have better a solution for you below. Due to the unique configuration of your bike, you would need to return the Stage-3 kit and purchase 2 different year kits to create a "hybrid" Stage-3. The 1st kit contains the 1998-2013 radio & speakers, the 2nd kit contains the saddlebag kit for 2014+ bags. If you purchased the original Stage-3 kit from us at www.rockfordfosgate.com, I can help facilitate the return with a little incentive to make things easier. HD9813SG-PMX-STG2 (www.rockfordfosgate.com/products/details/hd9813sg-pmx-stg2/) This is the newest kit that includes the radio, SG fairing speakers, and the newer 800W M5 amplifier. TMS69BL14 (www.rockfordfosgate.com/products/details/tms69bl14/) This is the bag-lid kit for 2014+ Harley-Davidson saddlebags. This interfaces with the harnesses exactly the same for both 98-13 kits and 2014+ kits.

[@donaldstrickland9951]

What is the rca output harness used for? And do i need to connect it?

[@rockfordfosgate]

The RCA output is the low-level signal output of the audio. This kit uses the high level output from the speaker lines, and therefore the low-level RCA's are not required to be connected.

[@dwanjacquet162]

What other Rockford fosgate speakers can you use with this setup especially if you’re not connecting an amp

[@rockfordfosgate]

We highly recommend an amplified system so you can hear your music while riding on the highway. However, all our speakers are high sensitivity so you don’t need tons of power to hear them. For 1998-2013 models, we offer the following models: TMS5 - 5.25” tourpak speakers TMS6RG - 6” speakers for Road Glide TMS6SG - 6” speakers for Electra Glide/Street Glide TMS69 - 6x9” speakers for saddlebags

[@dwanjacquet162]

I bought the bike with the radio already installed, but I think it still has the Electra glide speakers , I’m gonna have to take it apart to see just what speakers are installed but I do know that at around 10-15 the speakers start to sound distorted, if I don’t have an amp what are the other speakers that I can use

[@Adilson-sousa]

Sou Brasil .. conseguimos saber o valor do Kit ?

[@rockfordfosgate]

$1859.99 U.S.D.

[@blullc3002]

For what you charge just include the”cool”usb port

[@rockfordfosgate]

It was around $49, but unfortunately we recently discontinued that extension port: www.rockfordfosgate.com/products/details/paux/

[@rphs19]

I got everything installed and power seems to be working but I have no sounds coming from my front speakers just the bag lid ones and those had a very low level of fuzz/static sound to them any suggestions/help ?

[@rockfordfosgate]

STEP-1: Turn the system off and move each switch on the front of the amplifier to make sure all of them are fully engaged. Test the system. If that doesn't work, proceed to STEP 2. STEP-2: At the amplifier, first switch the LEFT and RIGHT INPUTS to see if the audio switches from the bag-lids to the fairing. If so, we have something going on in the source unit. Make sure the BALANCE and FADER are set to their CENTER positions. If audio continues to only come from the bag-lids, then we have something going on with the amplifier or connectors. Remove both connectors from the amplifier outputs and check the PINS are properly set into the molex. Plug the connectors back into the amplifier to see if the audio returns to the front speakers. If you're still having problems, I suggest contacting our Technical Support at 1-800-669-9899 to make sure there isn't any issues with the T-harness. They can be reached Mon. - Fri. 8 am - 5 pm.

[@erniegonzales6101]

Where do you buy the interfering swap

[@rockfordfosgate]

Sorry, we don’t know what “interfering swap” means…could you clarify?

[@haydengladfelter7914]

Where can I find the amp tuning video

[@rockfordfosgate]

Our Tuning Guide sheets are available for download here: rftech.custhelp.com/app/answers/detail/a_id/1355/ If you have the exact kit as referenced in the video above, here's the direct link: www.rockfordfosgate.com/rnt/rnw/docs/1355/harleyamptuning_1998-2013_rfk-hd9813.pdf

[@haydengladfelter7914]

How do I order option for up for the USB

[@rockfordfosgate]

Unfortunately, we just discontinued the PAUX, but we are selling the PMX-USBP. We're not touting it as a replacement because it's just a USB port with no 3.5mm audio input. Unlike the PAUX, the PMX-USBP requires a step-up bit if you intend to install in the cig-lighter location. The mounting hole requires 7/8” (23 mm) rockfordfosgate.com/products/details/pmx-usbp/

[@cbdyna]

what size are the lid and faring speakers in this kit?

[@rockfordfosgate]

6.5" and 6"x9". This kit is actually being replaced with a newer model featuring an IPX6 amplifier. You can find all the details on that kit here: rockfordfosgate.com/products/details/hd9813sg-stg3/

[@cbdyna]

@@rockfordfosgate Thank you. Couple questions if you do not mind- 1. I have 5.25 speakers in the fairing currently. Does this kit come with the adapters? 2.- Does this kit come with the template to cut out the 98-2013 lids?

[@rockfordfosgate]

@@cbdyna Yes, the TMS6RG speakers include the adaptor ring with integrated grille. Yes, the 6x9" saddlebag speaker kit includes the templates as shown in the video. Note the kit that is being discontinued above includes the saddlebag kit, whereas the newer replacement kit requires the saddlebag kit to be purchased separately. Same exact system, just kitted differently based on customer requests ... allowing you the option to upgrade at a later time or go ahead and pull the trigger on the full system.

[@Blade-hp9mn]

Which usb adapter for the cigarette lighter replacement did you use?

[@rockfordfosgate]

Hi Blade1100, it's called the PAUX and mates perfect with the PMX-HD9813: rockfordfosgate.com/products/details/paux/

[@RockfordF150Bass]

Weren't you guys coming out with a newly designed T2500BDCP?

[@rockfordfosgate]

We don't have any news releases regarding this. All our announcements are listed here: www.rockfordfosgate.com/news/ . Curious, where did you hear this?

[@mullen1972]

What’s the total cost of this kit

[@rockfordfosgate]

Hi mullen1972, you can find pricing, features & specs on the HD9813SG-STAGE3 here: www.rockfordfosgate.com/products/details/hd9813sg-stage3/

[@littlestomper9493]

$

[@Frankstgeorge88]

@@rockfordfosgate $2800. Damn!

[@michaelhook42]

Not worth it, the kit I bought the amp was not working. After explaining the installation to them was correct I sent it back, they said it was fixed. It worked for about 6 months then it went out again. Won't ever go back to Rockford fosgate to expensive to be this cheap

[@michaelhook42]

I bought this kit for my Road Glide, amp was defective right out of the box. Sent it back and they said it was repaired. It worked about 6 months then it went out again. Never will buy a Rockford fosgate system again. To expensive to be this damn cheap

[@rockfordfosgate]

Hi Michael, sorry you ran into this problem right out of the box. This kit is for a Street Glide, but you say you installed on a Road Glide. Assuming you meant the HD9813RG-STAGE3, correct? When you got the amplifier back and rode with it, did the amplifier get wet at all? The TM400X4ad is not a “waterproof” amplifier.

[@littlestomper9493]

The saddlebag speakers say they fit 98-13 lmao. I own a 2003 ultra electra classic try installing them straight forward with the template then tried to screw the grill and speaker mount together only 2 of the 4 screw holes Aligned I'm thinking wtf. Call Rockford up the next day to see what the issue is they said the speaker kit wont work on factory fiberglass lids And it's in their discrepancy listed on their page unfortunately they don't tell their dealers that sell their products to to notify the customers/buyers of this product so i/you the end buyer will be sol and have to dish out $300 more for aftermarket lids and $200-500 for paint. Seems shadie to not worn the the customer in the videos!!! I've watch at least 5 of your videos and you did not mention nothing about fiberglass lids issues. Total bs

[@rockfordfosgate]

Hi Little Stomper, I apologize the dealer did not cover this with you. Could you share what dealer you purchased from? I actually produce all the training materials for our dealers and maintain the website, both of which indicate the disclaimers. There are 4 disclaimers on the COMPATIBILITY tab that we warn customers about on our product page at rockfordfosgate.com/products/details/tms69bl9813/. The videos are focused on the installation itself and does not cover any box opening, applications, features or performance. What aftermarket lids are you considering?

[@littlestomper9493]

@@rockfordfosgate eastern performance was the dealer. Hogtunes are the lids I order up sould be here in a week still alot of extra expense I wasn't or shouldn't have to eat

[@rockfordfosgate]

@@littlestomper9493 Thanks for the dealer information, I'll reach out to them. I was going to see if we could help with ordering replacement H-D lids for you. However, if Hogtunes lids were ordered that feature integrated speaker grilles for 6x9" speakers, that is a completely different kit and is not designed to accommodate the Rockford Fosgate speaker grilles & mounting brackets.

[@littlestomper9493]

@@rockfordfosgate I would take the money that the lids you were going to get to off set the price of the hogtunes lids. The hogtunes lids still should be able to mount the factory Rockford 6×9 and speaker protectors?

[@rockfordfosgate]

@@littlestomper9493 Please contact me at [e-mail] to continue this conversation in private.