Sealey Trolly Jack 2001LERE vs Snap-on Professional Jack, Full Review & Test Low Entry Trolley Jack

I Needed A Professional Quality Low Entry Trolley Jack, Will The Sealey 2001LE Rocket lift Fit The Bill Or Is It Cheap Rubbish?
Let's have a close look at the jack, and put it to the test.
Link to the Jack on Amazon £143 amzn.to/3K06DML
#sealey #tools #snapon

[@AlanL200Truckman]

Morning Ant Great upload as always.... I've had 2 of the Sealey low profile 3 tonne Jack's (model 304OAR) since Oct 2019.... FANTASTIC bits of kit. Can't fault em..... Such a QUICK lift too & such an easy action. They lift the Truck like it's butter. Max height 533mm so definitely handy for the L200. You'll definitely enjoy using.. Stay lucky. Stay safe. Stay healthy. Alan L200

[@aaanton11]

Yes Alan, yours lift an extra 40mm with a bit more beef, I wanted something lighter, was considering the 1.5 tonne model as it looks very nice and its not often I will need anything larger my old yellow jack was 1.5 tonne and worked like a charm, Thanks for the great comments👍🏻👍🏻🛠

[@jimbo9310]

Great video ant well done and very informative thanks 😊

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@rsmickeymooproductions4877]

Nice jungle music as well. Good review. I bet the Snap-On still out lives this new kid on the block

[@aaanton11]

I think so! Thanks for the great comments👍🏻👍🏻🛠

[@PhantomMark]

I really like mine, I have a really low E46 M3 race car, and this is the only jack I found that could get under it, really nice bit of kit IMO.

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@roadwarrior8560]

Nice one mate, subbed.

[@aaanton11]

Much appreciated! Thanks for the great comments👍🏻👍🏻🛠

[@normsmowers4758]

Nice bit of kit should make life easier 😀

[@aaanton11]

I love how low it goes, Thanks Norm for the great comments👍🏻👍🏻🛠

[@dannywhite1392]

Ive just got this for a bargain £92.99 from euro car parts 👌. BTW your meant to bleed the jack with the release fully open, not closed ✅️

[@aaanton11]

Bargain Thanks for the great information👍🏻👍🏻🛠

[@gavjlewis]

I have a very similar jack. The ultra low side skirts gets scuffed up and the paint chips off and rust forms. I had to sand it down and repaint it. Now it has tape on it and when the tape gets scuffed up I just replace it before it takes the paint off.

[@aaanton11]

I will need to be careful with this one then gav, hopefully it will last a few years, Thanks for the great comments👍🏻👍🏻🛠

[@w00t-w00t]

Great video - thanks for bringing it to our attention! Just managed to grab one in an eBay promo for £120. Bargain.

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@garrynutter860]

Nice comparison, Looks like the Snap-on won on lowering. Looked more controllable.

[@aaanton11]

She is a beauty, the old skool snap-on is a rare commodity but the weight is an issue, its so dam heavy😂 and the low entry was doing my head in, Thanks Garry for the great comments👍🏻👍🏻🛠

[@peterthompson3369]

Is the pad removable on the new Sealey jack? Can it take a Transmission adapter in a 30mm spigot?

[@aaanton11]

Unfortunately not, Thanks for the great comments👍🏻👍🏻🛠

[@jonnysedge7412]

I just bought a pair of 3000LE's, I don't think you did the inital bleed procedure correctly. Going by the manual it says to have the handle turned fully anti-clockwise and pump 20 times so the actual jack arm won't go up. Once you've done this on the last 20th pump on the downward stroke turn the handle all the way clockwise then you can use the jack as normal

[@aaanton11]

Mine works like a charm, Thanks for the great comments👍🏻👍🏻🛠

[@toy838]

Good vid thanks

[@aaanton11]

Glad you enjoyed it, Thanks for the great comments👍🏻👍🏻🛠

[@frednetherlands887]

Thank you.

[@aaanton11]

You're welcome! Thanks for the great comments👍🏻👍🏻🛠

[@philipbunker146]

Does the jacking pad remove, and if so what diameter hole is left for fitting a cross beam?

[@aaanton11]

The pad is bolted on, so not easy to pop off. Thanks for the great comments👍🏻👍🏻🛠

[@rabfraser1234]

hi ant you cost me a fortune with these tools ,,,i would say that the Milwaukee hoover is the best tool ever love it ,can i ask i have a little aygo city bug its developed a problem when on motorway its sways from side to side as if its windy but it not too windy any clue,,, ball joints are ok track rod ends seem ok just thought with your knowledge with them you might have came across it before ,,thanks rob,

[@rabfraser1234]

thanks ?

[@aaanton11]

I would look more at the road surface, the trucks cause ruts in the road and the bugs wheel base sits right on the edges of these ruts, this can make the car move all over the place, Thanks for the great comments👍🏻👍🏻🛠

[@rabfraser1234]

@@aaanton11 thanks for that but I been on the same road for the last 2 years can't remember this snaking But it's OK when driving around town...

[@kevinking217]

I have the same old jack as you, but it always gives me back pain when I lift it. it is too heavy to move.

[@aaanton11]

Yes the old one is so heavy, Thanks for the great comments👍🏻👍🏻🛠

[@MrZimmaframe]

This looks identical to the Halfords Advanced one, but you get 3 years warranty with the Halfords one.

[@aaanton11]

Its very similar, the Halfords one is £200, is only 2 tonne, and there are differences in the build, Thanks for the great comments👍🏻👍🏻🛠

[@MrZimmaframe]

@@aaanton11 Yes 200 for the 3 ton halfords advanced. But £165.99 for the 2 ton which is more compareable to the Sealey's 2.25, 3 year warranty compared to Sealeys 1 year. I got my 3 ton Halfords Advanced on Black Friday and only paid £150 for the 3 ton, and I think the 2 ton was only like £120. The sealey is good for the price, i have noticed less weld on the rear wheel area and no weld join the the middle of the sealey. But both look like great jacks.

[@Danme1987]

I have returned 2 halfords ones as the rams were being scuffed internally and scraping the ram metal on metal. The jack worked ok but this will eventually kill the seals. I checked top and bottom with the Jack fully up.

[@markholyoak9790]

how high does the new jack lift please?

[@aaanton11]

Max Lift 495mm nice and high, Thanks for the great comments👍🏻👍🏻🛠

[@nelson1tom]

Do you guys have harbor freight over there?

[@aaanton11]

No I wish there was, closest is Costco Thanks for the great comments👍🏻👍🏻🛠

[@bibs3655]

Bled it wrong my man. Need to release it then pump.

[@aaanton11]

Thanks for the great information👍🏻👍🏻🛠

[@stephenk0nig252]

You can sometimes get around not having a low jack. Drive onto some wood first to raise the car up or start the lift with a scissor jack. Nice looking jack but for DIY home use it's expensive really. I use a jack just to get the car onto axle stands.

[@aaanton11]

good tip, Thanks for the great comments👍🏻👍🏻🛠