I had problems with my left side turn signal on my 2004 silverado, the cause was a bad flasher relay.Showing the problem and the fix in that video www.amazon.com... Thanks for watching, give thumbs up and subscribe for more .
Пікірлер: 250
@chrisl32117 жыл бұрын
Thanks for sharing! I had the same problem with my 2004 Chevy Avalanche. I bought the same part and then did the replacement in about 10 minutes. Thanks again!
@obscur1567 жыл бұрын
Glad it helped you out,thanks for leaving a comment i appreciate it very much.Thanks for watching and dont forget to subscribe for more.Best regards.
@ericbarner48013 жыл бұрын
Now all you gotta do is disassemble your cluster and solder the the resistors back to the board to get that PRNDL display back
@margueritebozeman54182 жыл бұрын
hi, my problem is left turn signal blinks to fast. i replace front and back bulbs both were bad. didnt fix the problem. right side works as it should. any suggestions? michael in san antonio. oh yea i have a 2006 silverado, half ton, 2 wheel drive
@lewis25532 жыл бұрын
@@margueritebozeman5418 A fast blink usually indicates a lower than normal resistance to ground at the output of the flasher on the affected side. That causes higher current and the flasher will sense that. If you haven't already done so, check those little marker lights also on that side as they sometimes flash with the main signal light. One of those might be shorted or you might have a pinched wire or a short in a socket on that side. If you move a wire while it's blinking and the flashing changes frequency, that's a good sign you're near the problem. Another thing you could do is to disconnect the battery and take out the flasher. Make sure the signal lever is in the center position. Then remove one right and one left rear signal light bulb. Next take an ohmmeter and measure the resistance from one terminal to the other on the left bulb socket and then check it the same way on the other side. They should read the same. If they do, the problem is probably not in the bulbs or wiring. Before you replace the bulbs, do the same measurements again after reinstalling the flasher. If the readings are different between the two sides, you probably have a bad flasher.
@ericis42 жыл бұрын
@@margueritebozeman5418 junction box in front of rear bumper by spare tire could have corrosion
@layasimon92376 жыл бұрын
Husband had the same issue was slightly worse than the problem you showed. He followed your guidance and was able to replace the relay in about 15-20 minutes. The relay didnt want to come out otherwise was extremely straightforward. Video was extremely helpful. Keep up the good work. His truck is a 2003 silverado 2500HD CC/LB
@obscur1566 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot.Thanks for watching,best regards.
@SSinthaNorthwest6 жыл бұрын
This helped me out big time. My right turn signal stopped working in my 2004 Silverado. I bought this same part and it resolved the issue. Thanks!!!
@obscur1565 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot. Thanks for watching ,best regards.
@Ruiz921_2 ай бұрын
Did both front and rear turn signals go out on you? I'm having same issue
@rebeccag64206 жыл бұрын
Thank you! The guy at the auto parts store told me that part goes in the fuse box under the hood. I had to speed your video up to 1.5 , lol , but you solved my problem, I fixed it in 10min. Bam
@obscur1566 жыл бұрын
I am happy that it helped you out. Thanks for watching,regards.
@motionvista5 жыл бұрын
THANK YOU!! Changed this myself and fixed my right turn signal. 2004 Silverado. Cheers!
@obscur1565 жыл бұрын
Cool,that's why i make these video. Helping others is great. Thanks for watching,regards.
@agordon200244 жыл бұрын
Thank you! I had tried everything I could think of to solve this problem. Yes, the original flasher is a bear to get out and is in a position difficult to reach.
@obscur1564 жыл бұрын
You are welcome buddy. Glad that video helped you out. Thanks for taking the time to comment,I appreciate it. Thanks for watching, regards.
@petersisserson20836 жыл бұрын
Thank you for sharing. I recently installed LED rear lights on my 2003 Silverado. Got the blinkey-blink problem. Saw your video, bought the flasher relay, and fixed the problem in about 15 minutes. Great video! Thanks.
@obscur1566 жыл бұрын
I am happy that you solved your problem with this video,Thanks for taking the timee to comment .Thanks for watching,regards.
@ashmatheweats16264 жыл бұрын
Does this fix issues for the front and back signals?
@petersisserson20834 жыл бұрын
@@ashmatheweats1626 It did for me! I think they both work off of the same relay.
@lewis25532 жыл бұрын
You are right about this part. And to save your viewers extra time, money, and grief, they should read this comment completely. First, don't waste your money on a Haynes repair manual if don't have one already. They're worthless. They just tell you that "the type of combination flasher unit used on the covered models has complex internal circuitry, and can't be tested using standard electrical test equipment. Refer to the wiring diagrams at the end of this Chapter and test the circuitry before replacing the flasher with a known-good unit." I'm guessing Chilton's would be about the same. Basically, what they are saying is, "You're too dumb to fix anything more complicated than a shot light bulb or a blown fuse." And to assure that you DON'T find the problem, they give you an incomplete diagram. Oh, they show you the switches and fuses, but half, if not all, of the wire colors are wrong. And you will NOT see anything more of the flasher unit other than a rectangle with 4 wires going to it. The contacts of the relays inside it ( "simple" circuitry) are not shown, even though the relays are the switching elements that turn the light current on and off. That means that Haynes has replaced the relay contacts with straight lines in their diagram as if the driver is going to sit there, with nothing else to do, and toggle the turn signal switch on and off the whole time he's turning. No, the real story here is that Haynes, most likely on behalf of their benefactor GM, has hidden this information from you to prevent your knowing that, even with it's "complex internal circuitry," this flasher STILL has SIMPLE relays inside that you can check with two pieces of standard visual electrical test equipment -- your own eyeballs! So just pull that sucker out, remove the cover, and look at the "normally open" relay contacts. The cover comes off easily with the help of a small flat blade screwdriver. There will be 3 relays inside -- 2 small ones for the right and left signal section and 1 bigger one for the hazard flasher section. The little ones are usually the first to go. If you close a relay manually, you can see the normally closed contacts on the opposite side of the part that moves. Compare that to the normally open contacts. On a bad flasher, you will see that the NO contacts are all pitted out and may even be welded together, as opposed to the smooth, shiny, NC contacts on the opposite side. Second, don't throw money away by replacing the turn signal switch first. That's probably what Haynes and GM want you to do, but your could buy your kid a bicycle with that, especially if you add the cost of a worthless Haynes manual to it. Third, time and grief. Don't even waste time tearing down a lot of stuff and troubleshooting wiring and all that crap, because A. The Haynes wiring diagram is DELIBERATELY wrong and so are the wire colors on it, and B. All you need to remove is the instrument cluster bezel, the "knee bolster" (that plastic cover below the steering column), and the bad flasher. The cover has 2 screws at the bottom and two metal clips that take about a ton of pressure to remove at the top, it seems. GM wants you to break the plastic cover, so they use these. Be careful. You can wiggle the flasher back and forth with both hands til it gives up and comes out. Good luck! I'm speaking from experience with my 2003 Silverado. By the way, Advance Auto Parts sells a replacement unit with 30 amp contacts, but I suggest ordering it a few days early since they don't stock them in the stores. These are better for use with a trailer, but lo and behold, another conspiracy to sell more parts! The best they sell without ordering and waiting has 20 amp contacts, so they won't last as long! But since I don't have time to wait right now, I have to go get one of those crappy ones today. 😠
@obscur1562 жыл бұрын
Good write up Lewis. Thanks for taking the time to comment , i appreciate that. Thanks for watching,best regards.
@dirkdaddy22 жыл бұрын
+1 on Haynes being a waste of time. Between today's KZbin and if needed a factory manual (pays for itself first time you avoid a dealer visit) can do about everything. PS> My blinker blinks all 4 lights, not sure what is the problem but thinking since bulbs are OK I'd start there with this thing.
@lewis25532 жыл бұрын
@@dirkdaddy2 Yep, your blinker is on a separate relay from the turn signals. Either or both of the signals can quit without affecting the hazard flashers.
@dirkdaddy22 жыл бұрын
@@lewis2553 Problem on 02 Avalanche was not the module you had trouble with (the 02 doesn't actually use that part your video references when I dug into it, its a cube shaped old school type) it was the rear lighting electrical hub thing that connects 4 connectors and mounts to body behind RR wheel. Tough location. Moisture had gotten inside of the connector on the bottom center connector, causing corrosion. The corrosion built up enough that it created a bridge of corrosion between two of the bottom most terminals, which allowed both sides to illuminate some when one side directional indictor blinker or the other was turned on. I was able to use compressed air and wd40, a pointy poker to scrape the female plug out. A corroded end of the connector broke off, but it is now working. Will look for that short harness section perhaps at salvage yard in future.
@kevinekvall50715 жыл бұрын
Great instructions on removal and which replacement module to get, one suggestion for anyone having a problem removing the flasher module is to use a large channel lock and open them fully and grab the top and bottom of the unit from the front for better leverage. 20 minutes of trying to get it out by hand and did not move, 30 seconds with the channel locks. Mine was so tight in their, it did not want to budge.
@obscur1565 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot. Thanks for watching ,best regards.
@kanyedeyoe81212 жыл бұрын
Me too
@jasonhepler99259 ай бұрын
Thanks for tip its works by replacing this part with a led part on my '03 silverado hyper flash is gone and got mine at O'Reilly's auto parts
@obscur1569 ай бұрын
Glad it helped you out with your problem. Thanks for taking the time to comment,i appreciate that. Thanks for watching,regards.
@BobbyW007 жыл бұрын
Thanks for the video. I saw the reference to it here on KZbin from your Amazon review of the LM487 flasher module.
@obscur1567 жыл бұрын
Thanks BobbyW00,for taking the time to comment, i appreciate it very much.Dont forget to subscribe for more . Best regards.
@kwood1985 Жыл бұрын
2005 Chevy Silverado 1500 2WD part LM487 at AutoZone. This was expensive for me $77.00before taxes. It totally worked!!! My right turn signal made no noise and no flash but my left side worked. I changed bulbs and fuses none that worked. My neighbor told me about this part thats behind the fuse box i was not aware. I Went KZbin and seen this video. 💯💯💯👍🏾👍🏾👍🏾
@obscur156 Жыл бұрын
Glad it worked for you buddy. Thanks for letting us know,i appreciate that . Thanks for watching,best regards.
@M.V.4 жыл бұрын
Thanks for the diagnosis. I was then able to open the ralay figure out which one wasn't making and then spray with brake cleaner followed by compressed air and the problem is solved. See how long for though 😂
@obscur1564 жыл бұрын
Glad it helped you out. Thanks for watching,regards.
@cesma254 жыл бұрын
Buen video, corto y claro para arreglar el problema Algunos solo pierdes tiempo y te confunden gracias amigooouuu 👍👍👍
@obscur1564 жыл бұрын
Me alegro de que te haya ayudado. Gracias por tomarse el tiempo para comentar, lo agradezco mucho. Gracias por mirar, saludos.
@crlaw756 жыл бұрын
That is what I miss about those trucks; replacing a flasher unit, instead of the flash rate controlled by the BCM now. By what you did here, you can add LEDs without installing a resistor per turn signal unit.
@ATrueSound Жыл бұрын
Hey I dont know who needs to hear this but Instead of removing all the dash components, I just saved myself so much time by going underneath the pedal area to access the relay module instead.
@debsingle55 жыл бұрын
Thank You for your sharing I am over 60 yrs female and I installed mine,thanks so much
@obscur1565 жыл бұрын
Glad that you were able to do it your self. Thanks for taking the time to comment,i appreciate it a lot. Thanks for watching and subscribing,best regards.
@PETE17608 ай бұрын
Thank you man you just helped me with my problem!
@obscur1568 ай бұрын
Thanks for letting me know, I appreciate that. Thanks for watching,regards !
@kynanhudson12 жыл бұрын
Thanks I really appreciate your Insight you were a nail on head it's just what my 2006 Chevy Silverado needed 👍
@obscur1562 жыл бұрын
Glad it helped you buddy. Thanks for commenting, I appreciate that. Thanks for watching ,regards
@laliruiz717 жыл бұрын
Thank you so much your video was so helpful for me .
@69dragrace6 жыл бұрын
Good video, thanks for doing this. I would have never located that module.
@obscur1566 жыл бұрын
I am glad that it helped you out, thanks for taking the time to comment . I appreciate your positive comment. Best regards.
@freggo66045 жыл бұрын
My relay is acting up too. Tried to located by sound, and was guessing left side behind the panel. Oh god I thought, that's going to be a bit#$ to get to. (why would they not put it in a more accessible location like the fuse box?) Thanks to your video I now know what I will be doing next weekend ! The few down votes are most likely GMC Mechanics :-)
@obscur1565 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot. Thanks for watching ,best regards.
@Torontotootwo3 жыл бұрын
Best video so far on this problem.
@obscur1563 жыл бұрын
Glad that you liked my video and helped you out. Thanks for taking the time to comment,i appreciate that. Thanks for watching ,regards.
@multymore15 жыл бұрын
Gracias señor ase más de un mes que estaba batallando con mi Silverado 2004 gracias se lo agradezco 👍
@obscur1565 жыл бұрын
De nada !
@jessedukelacrosse64703 жыл бұрын
Made it fast and easy for me to fix my Chevy relay, thanks man 👍🏼👌
@obscur1563 жыл бұрын
Glad that it helped you out. Thanks for taking the time to comment,i appreciate that. Thanks for watching,regards.
@gerardocruz96045 жыл бұрын
I was about to buy the hole switch for the turn signal ... thanks for the info!
@obscur1565 жыл бұрын
I am happy that it helped you out. That's why i make these videos. Thanks for watchin,regards
@emmlawn.powerwashing77106 жыл бұрын
Thanks for for your help on this video
@obscur1566 жыл бұрын
My pleasure ,thanks for taking the time to comment cause i appreciate it a lot.Thanks for watching,best regards.
@bakerviewlandscaping3275 жыл бұрын
Could this be the cause to the hazards going on when I hit the left signal when my trailer is connected ?
@joeh42534 жыл бұрын
had the same problem. 2003 gmc yukon. i finally came across your video today & replaced the hazard/turn relay. there are certain times & places on my daily commute that left blinker always failed me; i could bet money on it. we will see what she does on Monday! i opted for the $30 non-LED compatible from NAPA Auto since my truck is bone stock. can’t believe this part goes for $75 at most places - that’s just ridic! even $30 is expensive for a 6-prong relay module i wish i would have done/seen this before i had to pick & pull the turn signal switch and replace it with mine. that was not simple as it looked and set me back a week. all for nothing haha
@obscur1564 жыл бұрын
I hope you have solved your turn signals problems. I agree with you ,its way too expensive. Thanks for taking the time to comment,your expertise will help others. Thanks for watching,best regards.
@joeh42534 жыл бұрын
obscur156 just wanted to confirm the turn signal relay module repair & replace was the fix. my left turn signal now functions 100%. thank you very much
@robertbellini64913 жыл бұрын
Thanks for taking the time to make this video. You’ve helped out the GM community!!!
@obscur1563 жыл бұрын
Glad it helped you out,thanks for leaving a comment i appreciate it very much.Thanks for watching and dont forget to subscribe for more.Best regards.
@ryansoltess60066 жыл бұрын
Very helpful. Thank you !
@obscur1566 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot.Thanks for watching,best regards.
@david75mv4 жыл бұрын
I had same problem with my 04 Silverado, went fine just like video until I tried to reinstall the lower panel and it wouldn't snap in place. I figured out the metal clip came off the plastic tab by noticing the right tab had a clip but the left didn't. Found the clip on floor, stuck it on, snapped in place fine.
@obscur1564 жыл бұрын
Great to see that it worked for you too. Thanks for taking the time to comment,much appreciated. Thanks for watching,regards.
@Lui5_5.02 жыл бұрын
Thanks for the video you made it really easy to follow and solve this turn signal issue!!!
@obscur1562 жыл бұрын
Glad it helped you buddy. Thanks for your comment,i really appreciate that. Thanks for watching,best regards.
@El_R976 ай бұрын
Thanks bro
@obscur1566 ай бұрын
You are welcome Budd.
@austinablefuldul4 жыл бұрын
Thanks for the info! I needed this.
@obscur1564 жыл бұрын
You are welcome my friend. Thanks for watching,regards.
@joevalencia47986 жыл бұрын
Yeah i got the same problem and a police already stopped me because i made a turn without turning signal but i had explain the problem and she was cool about it and let me go but told me to fix it asap
@IMWH1T3xK1LL3R4 жыл бұрын
what size motor you have? i have an 05 4.3 with 270k still purs like a kitten. hopefully this fixes my left turn signal as well
@obscur1564 жыл бұрын
Mine was 5.3L,i hope you will fix it buddy. Thanks for watching,regards.
@oaklysewell256 Жыл бұрын
Can just one blinker stop working because of the relay?
@obscur156 Жыл бұрын
Yes, absolutly. This is exactly what happened to me !
@booboohern5 жыл бұрын
Thank you that video helped.
@obscur1565 жыл бұрын
You are welcome. Thanks for watching,regards.
@diego3ful7 ай бұрын
Does anyone know if this can help me, my low beams turn of when i turn highs on and when i turn them off low beams come on, i already checked everything with connections and make sure everything is correct but nothing changed, im thinking this could be the problem?
@darryllancaster3897 Жыл бұрын
Thanks for sharing
@obscur156 Жыл бұрын
You're welcome !
@rodneywise6773 Жыл бұрын
I did not have to remove nothing on mine got up underneath there looked at it take a screwdriver and popped it out and about 35 seconds did not have to remove my - 2003 GMC Sierra 1500 I
@albertoc.7188 Жыл бұрын
thank you very much for the video os very helpful I replaced the flasher relay easy but my Chevy Silverado 2006 still have the same problem with the right turn signal front and rear what else can cause the problem please someone can help me
@obscur156 Жыл бұрын
Maybe check if there's a fuse for the right side, maybe turn signal lever??
@MrJacobCastro3 жыл бұрын
This only fixes rear turn signals from hyper flashing. Not the front ones.
@obscur1563 жыл бұрын
Sorry but nope,this relay is for the four turn signal and hazard and compatible with LED. Regards.
@bobbypuente74437 жыл бұрын
Right on target. Thanks.
@obscur1567 жыл бұрын
Thanks for leaving a comment,i appreciate it a lot.Thanks for watching,best regards.
@manuelcruz87953 жыл бұрын
I’m having a problem with my 2004 Chevy Silverado Turn signals won’t work at all , they won’t flash on the dashboard and either on the outside lights , but if I use my emergency lights they work on dashboard any suggestions? Thank you !
@obscur1563 жыл бұрын
I would check the fuse for turn signal first and change the relay if its not the fuse.If its the turn signal lever,its a lot more expensive than the relay. Good luck and keep us updated so it will help others with the same issue. Cheers.
@nbsjuli53993 жыл бұрын
any luck?
@chaparoo6946 жыл бұрын
I had a question my turn signal lights work but when my head lights go on for some reason the left blinker turns on as well but with the lights off the blinker works fine any suggestions thanks
@obscur1566 жыл бұрын
My head lights are on the automatic position so they just turn on when its dark,i don't turn them on manually.I am not an expert but it looks like there maybe something "electrical short" somewhere...Do you turn them on manually ?
@blindcarnage14824 жыл бұрын
Chaparo O I have the same problem.
@omarOKC3 жыл бұрын
Anyone find the fix to this mine is doing the same thing
@deeannawaldrop21077 жыл бұрын
thank you very much for your time
@obscur1565 жыл бұрын
Thanks for taking the time to comment,i appreciate it a lot. Thanks for watching ,best regards.
@CoreyFehr-yk5ow Жыл бұрын
I have a 2007 gmc sierra I just replaced the turn signal switch put a new fuse in the signal on the right side worked then I hit a bump and the fuse popped again
@obscur156 Жыл бұрын
I am pretty sure you have a short somewhere in that circuit !
@robertsrs4836 жыл бұрын
Great Vid Thanks, will try it, I have the exact same problem, but radio sometime shorts out when I play a Cd, any suggestions
@johnarabia6385 Жыл бұрын
So I have a 2004 Serra 3500 with one side the blink works other side it doesn’t but the brake lights work on both sides need help
@obscur156 Жыл бұрын
That flasher relay will solve your peoblem,...
@MattsShop7 жыл бұрын
I just had to replace the circuit board under the spare tire where all the tail lights plug in to. Brake lights wouldn't work and it wasn't the brake light switch at the pedal.
@obscur1567 жыл бұрын
That's sad,usually its the brake pedal switch.Don't ask why i know this.My Sierra 1990 had that problem...
@SHADOWURLD6 жыл бұрын
Thank you man.....
@obscur1566 жыл бұрын
Thanks for taking the time to comment.Thanks for watching ,regards.
@brianbake36552 жыл бұрын
Why does my 4 ways come on when I turn the left turn signal on on my 03 Chevy Silverado 1500 4x4 ?
@obscur1562 жыл бұрын
Generally this is something caused by the flasher relay going bad...
@rjames7380 Жыл бұрын
Will 487 work for 07 1500 new body style? Finding information is not easy
@obscur156 Жыл бұрын
Looks like it will fit ! kzbin.info/www/bejne/qJi1q4yGfrGIqrM
@hellgarr6 жыл бұрын
Helpful Video
@obscur1566 жыл бұрын
Thanks for your comment,i appreciate it a lot. Thanks for watching,regards
@hectorsaints4567 Жыл бұрын
Hey I put some led taillights and my blinkers don’t work what can I do ?
@obscur156 Жыл бұрын
If i remember ,that flasher relay was suposed to work with LED's.
@bobbysgirl29736 жыл бұрын
I have the same delay issue. But what if sometimes it is flashing the wrong signal? Like for instance you try to do left and it does right, and visa versa...
@obscur1566 жыл бұрын
Never had that problem, sould be the relay or flasher lever ...
@edcalderon73014 жыл бұрын
Did yuo fix it i have the seme problen right side works good the other one not... just hears like noce quikly in the relay... what can be bro?
@martinfamilyband6 жыл бұрын
nice job,
@obscur1566 жыл бұрын
Thanks for taking the time to comment,i appreciate it very much.Thanks for watching,regards. Merci beaucoup !
@roadrhino067 жыл бұрын
I just had to replace this exact relay 2 days ago in my 07 Sierra. Frigging expensive relay!!
@obscur1567 жыл бұрын
It is expensive for sure ,thanks for watching . Regards.
@seeno17 жыл бұрын
Scott Miller same here. Found one on Amazon for 27 bucks
@eastpaloaltosfinest7 жыл бұрын
GeniusDroid did you check your fuses?
@brandonjmitchell6386 жыл бұрын
I have a 2006 Chevrolet Silverado 1500 V8 I replaced that relay bought at Autozone. And checked the fuses replaced those 4 with 15a fuse's to, But still no turn signals? I don't understand why my turn signals ain't working AT ALL?
@carderalexander66513 жыл бұрын
Same problem and same truck, did you find a fix?
@Daniel_704_2 жыл бұрын
Great Video , I have an 04 Tahoe and the Left Turn signal is stuck turned on when the headlights are on , could this solve the problem ?
@obscur1562 жыл бұрын
Yes ,this can be the relay going bad !
@Comeoffitman4 жыл бұрын
I got a question. When you push that the lower panels that it was pushing that the if you was hard to clip it on it?
@obscur1564 жыл бұрын
Therewas some resistance but check before if everything is aligned and snap it into place.
@danieldawson70493 жыл бұрын
Just fixed my turn signals on my 2002 chevy silverado 1500 you should remind People that there is a fuse panel on the left Side by the drivers side on the opposite sides of the door.looked at the turn signals Fuse and it was blown, you should look at these fuses before you buy the the flasher Relay, the fuse cost 3 bucks and wala it Was fixed!
@obscur1563 жыл бұрын
It all depends on "what is your flasher problem". If they are not working on both side,the fuse maybe the cause. If working on one side only or intermittent,its not the fuse. But thanks for reminding us,thanks for watching.
@crimsontide19807 жыл бұрын
I have a 2000 Sierra, is the flasher relay in the same location on my truck ?
@obscur1567 жыл бұрын
I think it should be yes,they are all built the same, thanks for watching .
@chrisciraldo49354 ай бұрын
Did your flashers still work just no turn signals
@obscur1564 ай бұрын
They were working on and off...
@tk422-72 жыл бұрын
Thank you so much!
@obscur1562 жыл бұрын
Thanks for taking the time to comment, I appreciate that. Thanks for watching,best regards.
@frankmajor98364 жыл бұрын
I have a 2006 Silverado 2500 HD, my turn signals flash way too fast both my left and right but not my hazards ..... will this fix my issue? It all started when I upgraded my headlights/ turn signal
@obscur1564 жыл бұрын
Hi,if you upgraded to LED,its probably the cause...If i remember,the part i bought is compatible with LED. If you try that fix and its working,come back and drop a comment so others will know and benefit from it. Thanks for watching,regards.
@carlosorduna67223 жыл бұрын
My truck is an 04 Chevy 5.3 and it’s weird that I put the right turn signal it turns on the hazards will this fix it ?
@obscur1563 жыл бұрын
Never seen that problem my friend,the best way to find out is to try it ! Keep us updated if you try it. Thanks for watching and good luck with that fix !
@richie2dicks4686 жыл бұрын
What if your blinker won't turn off?
@obscur1566 жыл бұрын
Maybe the relay sticking on...
@christophercuevas21326 жыл бұрын
I have a problem with my 2000 chevy 1500 when I have my head lights on the signals don't signal the go to hazards some help please
@garryb.13345 жыл бұрын
You ever fix this? I recently have a similar problem.
@BigLex504 жыл бұрын
Did everything but my right turn signal still isn't working. What could the issue be if it wasn't the relay
@obscur1564 жыл бұрын
Maybe your turn signal lever !
@gavindecker58962 жыл бұрын
Would this cause your dash light to not come on my mileage and gaslight work but no blinker flashers or lights on my speedometer
@obscur1562 жыл бұрын
No,there are some small lights in the cluster that you need to change. There iis some video on how to change them on youtube.
@obscur1562 жыл бұрын
kzbin.info/www/bejne/fpmqhIVni7tpZ9E
@JoseRocha-ow8kq6 жыл бұрын
Hey I have the same problem with my Silverado 2005 but in the right side but it’s no flashing on the dashboard
@obscur1566 жыл бұрын
It should be the same relay !
@viktorrotkiv16986 жыл бұрын
I have ploblem with my turn signal...... It works , but the problem is when , the handle returns to the off position, the high beams turns on... Does any one have any idea .?.
@obscur1566 жыл бұрын
Probably a faulty blinker arm...Here is a link on how to change it : kzbin.info/www/bejne/nqnaZH-JrL-jiMU
@djkendrick7132 жыл бұрын
Can a bad relay flasher cause the corner lights not to flicker as well?
@obscur1562 жыл бұрын
I am not sure on this one but its good for LED and no hyper flash.
@0s0213 Жыл бұрын
Yooo you ever figured it out? Installed LED flasher every good except the side marker bulbs they only turn on in park.. i swear they worked together wirh the turn signals. So lost been looking for answers :(
@erwin69l6 жыл бұрын
Would this relate to me when I turn me right turning signal my head lights go of
@obscur1566 жыл бұрын
Sorry ,i don't know.
@renanh79835 жыл бұрын
Mine go bright lol
@renanh79835 жыл бұрын
Im trying this tomorrow
@wildrodriguez21105 жыл бұрын
Right signal, right head light turns off and the high beam turns on for left. I need to a solution to this problem
@garryb.13345 жыл бұрын
Any of you solve your issues? How? Thanks
@ilicr99345 ай бұрын
Will this work on a 2008 chevy silverado?
@obscur1565 ай бұрын
There is good chance that the answer is YES. Check if the relay is at the same place !
@ilicr99345 ай бұрын
@@obscur156 thanks 👍
@jessewillars53634 жыл бұрын
My issue is that the right side turn signals will not flash and the emergency flash will not work either. But every thing works on the left side. Any suggestions?
@obscur1564 жыл бұрын
I did not try the hazard flasher when i had problems but could be that flasher relay !
@jessewillars53634 жыл бұрын
@@obscur156 Thanks for your information.
@obscur1564 жыл бұрын
@@jessewillars5363 You are welcome.
@1lochvy3 жыл бұрын
Will it work for a Silverado?
@obscur1563 жыл бұрын
Mine was a silverado 2004
@MrReadandlearn Жыл бұрын
What year ? It matters.
@obscur156 Жыл бұрын
2004
@damnkeh3 жыл бұрын
wilk this fix my brake issue, my brakes won’t turn on only the 3rd brake light turns on.
@obscur1563 жыл бұрын
Have you check all your brake bulb ligths ? Check fuses if all brake ligths dont come on. I know that there is a switch under the brake pedal that makes brake ligths to come on,maybe its that switch !
@damnkeh3 жыл бұрын
@@obscur156 yes ive checked all of them and i think it’s probably the switch under the brake pedal
@luislopez87466 жыл бұрын
My turn signals work good but the left side signal flashes to much when you put it, I already changed the light bulb from the back that was bad and it’s the same problem with the new one. Everything else is okay just that part with the signal that not even with a new bulb does it stop flashing. Does somebody have any advice? Or any idea how to fix it ?
@obscur1566 жыл бұрын
Have you changed the relay ?
@edcalderon73014 жыл бұрын
Did yuo fix it?
@nbsjuli53993 жыл бұрын
i replaced the flasher and still had no luck, any suggestions?
@obscur1563 жыл бұрын
I would check the fuse.If both signal are not working it could be the signal lever !
@urielgarcia6936 Жыл бұрын
I think I have the same problem, but I have the turn signal mirrors.. but only the left side burns the fuse not the right side.. those anyone know what it could be?
@obscur156 Жыл бұрын
If jts burning the fuse,its because you have a short circuit somewhere in your left side...
@urielgarcia6936 Жыл бұрын
@@obscur156 ok thanks I’ll check it out
@gustavouribe5184 жыл бұрын
My truck was stolen I just recover it but my signals don’t work and hazard emergency button missing anybody have an idea was wrong it
@jeremiassalazar87346 жыл бұрын
I changed the relay but my blinker is still hyper flashing with the LED lights I installed . what can be the problem?
@obscur1566 жыл бұрын
All your blinker are fast or just one side ?
@jeremiassalazar87346 жыл бұрын
obscur156 all of them. I work at Napa and I got the LM487 that said its LED compatible but I am installing another tomorrow as sometimes they come defective
@jeremiassalazar87346 жыл бұрын
But once I changed the relay the emergency light blink normal but then when I put the turn signal they blink fast still
@obscur1566 жыл бұрын
Oh,that's weird. Give feedback tomorow when trying another one. LED light often do this.
@Princeofsp2155 жыл бұрын
you need to install load resistors on each side the led lights are on
@caves5110 ай бұрын
Probably a multiple relay … the two pins on the bottom should be the actual flasher IMAO
@Julianamado13 жыл бұрын
Just put a new one in mine, cause I have the same problem when turning left. Now blinkers are fast, any idea what’s going on ?
@obscur1563 жыл бұрын
Sorry ,i don't know .
@justinmuscle3 жыл бұрын
I can’t get mine out idk but it’s in there super right
@justinmuscle3 жыл бұрын
Tight
@obscur1563 жыл бұрын
@@justinmuscle Yes,its hard to take out. Good luck buddy.
@bikelifejb9875 Жыл бұрын
I have a 2005 Chevy Silverado I took the original relay out an put a new one in but it wasn’t novita. An now my signal lights or my 4way flashers will not work I also have have LED lights on my truck does anybody know why ?
@obscur156 Жыл бұрын
Should have gone with Novita and yes it works with LED's.
@bikelifejb9875 Жыл бұрын
@@obscur156I thought the one that I ordered was novita but it wasnt do you think that was my problem? I just order a novita today I have to wait til tomorrow to get that one do u think that one will solve my problem an make my turn signals an 4way hazards work again ?
@obscur156 Жыл бұрын
@@bikelifejb9875 Hard to tell,what was your symptoms,working and not working or just stopped working and never worked after ?
@bikelifejb9875 Жыл бұрын
@@obscur156they was working but my left signal light had hyper flash. The original Gm relay was in there so I tried to replace it with a new one but didn’t have novita on it an when I did signal lights didn’t come back on I took that one out an tried putting the Gm back in still didn’t work so I’m confused now.
@bikelifejb9875 Жыл бұрын
I’ve figure out the problem why my signal lights an 4way hazard was blow out. I bought the Novita Flasher Relay an change my fuse it works amazing now. if anyone have this issue check your fuse panel inside the one by driver side door it’s “fuse number “25” that was blow out for me that controls your signal lights an 4way hazards
@ricardocastro67755 жыл бұрын
I just called autozone that relay cost 81.18 with tax lol i will be visting my nearest salvage yard lol
The issue I have it that the high beams turn on when I signal to the right
@obscur1564 жыл бұрын
Just guessing but maybe the signal lever issue there...
@jeff7389 Жыл бұрын
Insanely ridiculous how much the relay cost. Looks like I'll be using hand signals.
@obscur156 Жыл бұрын
Yes they are expensive,insane price. Maybe scrap yard will cost a lot less ! Good luck buddy . Thanks for watching,regards.
@planedr5 жыл бұрын
Good video, but how about a shitty music warning at the beginning? My headphones are now full of blood. Thanks.
@obscur1565 жыл бұрын
Yes ,i have to agree about this intro...That's why i don't use it anymore. Thanks for watching,regards.
@deeannawaldrop21077 жыл бұрын
why when i use my right turn signal my bright lights come on 2005 chevy silverado other divers sometimes gets a bit angry cause they think i'm doing it on purpose
@obscur1567 жыл бұрын
I guess maybe you have a faulty flasher lever or when you use your right turn signal ,you may be pulling or pushing at the same time and your bright lights comes on. Just guessing here.Thanks for watching,best regards.
@deeannawaldrop21077 жыл бұрын
at first i thought i might be pulling or pushing it also, so i started paying more attention when i used it, but that wasn't it so now when i turn right i just hold my linker arm up just enough for the blinker to start blinking while i turn but that is getting annoying lol thank you for your rapid response
@obscur1567 жыл бұрын
So,thats probably a faulty blinker arm.Can;t help more then that.Maybe you can ggogle your problem and find an answer.Good luck.
@obscur1567 жыл бұрын
kzbin.info/www/bejne/nqnaZH-JrL-jiMU
@deeannawaldrop21077 жыл бұрын
thank you very muh for your help
@caves5110 ай бұрын
PS flasher used to be $1.50 , what a ripoff
@obscur15610 ай бұрын
Agreed !
@thomarbau3 жыл бұрын
Loud opening music sucks. Modulate.
@obscur1563 жыл бұрын
True,i will try to lower it with youtube editor. Thanks.
@joeKisonue3 жыл бұрын
Make it shorter, I had to shave twice.
@obscur1563 жыл бұрын
Pretty decent ,i shave twice a week too ! Thanks for watching,regards.
@joeKisonue3 жыл бұрын
@@obscur156 I made a short. 04 siverado blinker change
@mastersmind6024 жыл бұрын
Lier !! How come you didn't put signal on right side
@obscur1564 жыл бұрын
Because my problem was on the left side,no need to try the right side. This relay work for both side. Watch that video again. Thanks for watching,regards.