Patreon - / evcustoms Channel Support - www.paypal.com... EV-Customs Website - ev-customs.com Instagram - / ev_customs Facebook - goo.gl/tu3Qdk Music - Kontekst No Copyright Music
Пікірлер: 70
@Lobo-mv2ml5 ай бұрын
I have a Phantomgogo R1 36v scooter. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
@trevormallette5492 Жыл бұрын
Thank you for this video. Simple and straight to the point. You rock
@myklmenzie3 жыл бұрын
My Brudda hope all is well in ur life and if not then stay positive and strong as you can. I have burnt my DMS wires on my controller I would like to disregard having a screen altogether for the time being anyway. Can I run my controller without display and just hook up ignition wire to a standard on/off switch that should be possible right? I know I just watched u do it but urs has no display output.
@EVCustoms3 жыл бұрын
Yes for sure, all Display controllers can work without factory Diasplay...
@leshawnlee6402 Жыл бұрын
EV Customs ...my custom Ebike has a 12 amp flex volt battery with a "makeshift" circuit protection wiring [fused] ...how much Amp(fused) protection is necessary for a dedicated [48 volt to 52 volt system] -at [one] 12 Amp/60 volt running power management; ...also, how much for [two] 12 amp/60 volt active batteries, powering a 250/ 350 bafang front hub... ...can I volt to 1000 watt running with such configuration???... 😅
@maryannleach65843 жыл бұрын
Well another PAS problem. My Controller Red, Black, Bluishgreen and PAS is brown, yellow, black. Tried hooking up the 2 diff ways with blk to blk. Sensor works nothing from motor and when have on hit blk to blk motor gets power. Is this just bad sensor? I can't find any sensors with this same exact wiring as controller of course.
@Idiophones4 ай бұрын
Did you find solutions
@Idiophones4 ай бұрын
Did you find a solution?
@BuddaSlim10 ай бұрын
Bro can u help me out I lost my keys to my e bike 😢
@GodFartherOG8 ай бұрын
When I try to use my ebike now the wheel goes the wrong way, and it's the rear so when I try to use the ebike will out power the bike will peddle forwards but when power is on the wheel only turn when you peddle backwards and when power is pushed to the wheel it goes backwards at full power, and it has a 1000w motor so it's a bit scary I nearly broke my foot the bike doesn't have reverse can you please help or give me a few pointers.. ?
@imadghaiti46323 жыл бұрын
How do you recharge your battery ? Should you pass through the motor controller ?
@Lpipzster4568 Жыл бұрын
No there's a seperate wire in the battery
@JawadAhmadsahibzada2 жыл бұрын
plz make a video on indicators , back & head lights, flasher, relays, ACC 12 converter wiring video . i need for diy wiring harness ...
@Idiophones4 ай бұрын
Pas has many colors.. black brown, yellow, and black green yellow.. makes confusion..
@rockefelleragent13574 жыл бұрын
Hi again, will you please help me once I get the ignition key lock switch and a controller and throttle display for my scooter? I will need your help.
@ptoneywhitmore4 жыл бұрын
I'm putting a new controller on my bike and I'm unsure of which wires match. Black and green are common and remaining 3 aren't the corresponding colors.
@stu37754 жыл бұрын
hmm
@rockefelleragent13574 жыл бұрын
The chance of making it work will be at 5% as the wire plugs won't match, LOL.
@ALSmith-zz4yy4 жыл бұрын
The PAS sensor connects to the PAS wires on the controller. That's obvious but how do you enable or disable the PAS function as well as set the PAS level? My motor controller, like the example you used here, does not have connections for a display.
@EVCustoms4 жыл бұрын
Controllers without display have only one mode PAS assistant..
@ALSmith-zz4yy4 жыл бұрын
@@EVCustoms Thanks for your reply. So I assume then that PAS is always activated or can you put a switch in the wire to disable it when you don't want it?
@EVCustoms4 жыл бұрын
@@ALSmith-zz4yy is always activate, if you want to control it ... you can put one switch on positive wire of sensor...
@ALSmith-zz4yy4 жыл бұрын
@@EVCustoms Okay, got it. Thanks for the info.
@randyhynson2942 жыл бұрын
What Gage is the hot and black what gauge is it
@AnthonySonjosh5 жыл бұрын
Hi iv got th envi-motion n iv got power to evrywher n evrything works i jus seem to hav lost my pedal assist powwr n nothing happens weni use my throttle but its all showing up on my dash pad. Im pretty electrical eliterate so didnt wana touch anything thats gna kil my bike so iv cum to th pro's any advise would b so very much apreciated thanks!
@soleymanihimat4452 Жыл бұрын
Can you tell me how to connect the remote control to the motor drive
@lordofwar77135 жыл бұрын
Do you have Any wiring info on the boom BD578Z electric motorcycle
@mrnormsfanclub5023Ай бұрын
I have a question ? Please help
@Imazdadrags5 жыл бұрын
I think my throttle is faulty is there a way to bypass throttle or make the motor turn without throttle to test it? (can I put voltage on the white signal wire?)
@EVCustoms5 жыл бұрын
You can bypass the throttle if you short wires (red +) with signal (green or white), but be careful because the motor will be run on full speed..
@Imazdadrags5 жыл бұрын
@@EVCustoms Cool,Thank you.
@bob-ny6kn5 жыл бұрын
Throttle uses Hall Effect (magnet moving past a voltage). The white is the feedback from the throttle. The red is V and the black is ground. Measure the feedback as you move the throttle. If no feedback, look for the open circuit or Amazon.com a new one.
@traceylam76915 жыл бұрын
I have an electric bike, it has a switch on the battery which is under my sead, in the handle bar I can't switch the battery on and off, it only can change the speed of the electric, it has 3 speed choose on it, if I just want to paddle the bike without the electric, it is very hard for me to reach the switch on the battery, how can I add a switch on and off on the handle bar, then I can choose use paddle or electric when I was ridding on my bike. please let me on this question, thank you so much.
@EVCustoms5 жыл бұрын
Hi... you can buy one handle-switch and connect them i parallel with your battery power switch, to activate or deactivate the battery from handle.
@traceylam76915 жыл бұрын
@@EVCustoms thank you, is it hard to do it? I never touch electric before,
@drmunawarsaeedkhan54344 жыл бұрын
Hi I have jiefei super electric bike. I bought it in scrap. It's wiring was altered and I can't understand how to restore. It's controller has been changed I thought because does not fit on the frame, it's a bit larger. There are three batteries and brush motor.
@Zalixo6 ай бұрын
Thank you
@LiLMAMA1.5 ай бұрын
you didn't show how to rewire anything
@alfankosh15 жыл бұрын
my ebike motor have only 3 wire hall sensor how i connect
@EVCustoms5 жыл бұрын
You must have also power wires for hall sensors
@alfankosh15 жыл бұрын
@@EVCustoms the motor have 3 wire power and 3 wire sensor only.
@stu37754 жыл бұрын
@@alfankosh1 hmm
@myneninagasivasai14142 жыл бұрын
Please provide a pdf notes
@FDbroadcasting3 жыл бұрын
Can i replace a pas system to throttle?
@EVCustoms3 жыл бұрын
Only with arduino..
@FDbroadcasting3 жыл бұрын
Oke thanks for your answer. So i better buy a new controller with the throttle. I need a new battery aswell anyway. My motor is rated 180w and 24v I want to make it faster. How high in voltage can i go and is there a max. in watts I can take on the new controller?
@priyankiburagohain73813 жыл бұрын
Where to connect an emergency switch
@joaomorais45775 жыл бұрын
Hi there, i have a big problem an i cant solve , i have a e scooter have wires from steer possible the trottle light and battery lever indicator and power button and from bottom cames another wires possible from the brushless dc controller , the color of the cables are :4 reds (2 up 2 down), 4 blacks (2 up 2 down), 4white(2 up 2 down), 4 green(2 up 2 down) ,2 blues (1 up, 1 down),1 pink or soft brown (down) and 1 yellow (up) , can somebody help me ?
@EVCustoms5 жыл бұрын
My friend i can not understand what you writing there..
@valentinmajul97395 жыл бұрын
hello. my motor only has 3 cables. i cannot make it work. do you know what should i do?
@EVCustoms5 жыл бұрын
3 wires? colors?
@valentinmajul97395 жыл бұрын
@@EVCustoms witheblu, yelow, red
@stu37754 жыл бұрын
@@valentinmajul9739 how'd it go?
@jeffpribble38734 жыл бұрын
how to rewire a controller electric scooter valride
@azzz7998 Жыл бұрын
Bought a zoomo ebike no key I will be hotwiring it paid 150$ imma ride this shit return to zoomo for 400$ they said , I just wanna ride it before sending back .
@pollohertz14286 жыл бұрын
where to connect the battery charge cable?
@EVCustoms6 жыл бұрын
Charge wires must be connected on bms C+ C- pin's..
@pollohertz14286 жыл бұрын
bms?
@pollohertz14286 жыл бұрын
my battery had a bms, can i solder it right to that?
@leshawnlee6402 Жыл бұрын
BMS = (battery management system)
@tracezachdaniels42645 жыл бұрын
SO SHWEEEETTT...much love Tee with LIONS NAMED LEO.[the music worldwide}
@MichaelGallegos-r3h Жыл бұрын
Electrical wire ing engine 2cycle motor
@jamesthomas8481 Жыл бұрын
This is so bogus. Who doesn't have lights on their electric bike? Sorry. I was looking to wire up my rear lights
@brickcity9mm8962 жыл бұрын
Thanks alot for nothing
@justpoppinthings13 күн бұрын
This guy gets it 😂
@EVCustoms13 күн бұрын
Hey smart guy's.. Read the title..
@dominic337 Жыл бұрын
No
@fumanchutripitaka66394 ай бұрын
All very clever flashy graphics and video! But you don't actually explain anything so pointless! Sorry, not your fault but I am so fed up with the numerous KZbin videos claiming to give simple instructions on how to connect up battery - controller - throttle - ignition? But every video, set of instructions seems to give different explanation of wire colour/sequence! And when you've burnt out a controller or seen your ignition switch start smoking as you connect it up it's really not funny anymore!