Snowblower Turned Mini Bike… Crazy ENGINE SWAP!

Taking a 141cc 2-Stroke engine out of a Toro snowblower & fitting it into a mini bike!

[@AviewFromUnder]

Nice job! Love the 2 cycle powered stuff. The tuned pipe of the 2 stroke is amazing in how dramatic of a performance enhancement or detriment it can be. Any 2 cycle regardless of size when it has a tune that is working perfect with its intended load will have this anger and rip that is something only a 2 cycle can do. The volume and shape of the chamber is so critical to the displacement and intended power band adding or subtracting any length in front of the chamber can make unbelievable changes in power output. There are a lot of resources online that can help with this complex process. The up side is by getting the right shape and length in that can you will get power gains that would require a long list of expensive mods in the 4 cycle world! Good luck

[@mattyceks380]

Finally someone who dosent butcher the dimensions of an existing tuned pipe❤ and who takes pride in their work 👌 very clean build bro you've done a great job on it😁

[@petemartus8876]

Well thank you very much for your comment on my welding.I learned from one of the best a guy who worked at the tank plant.we worked together at th road commission.

[@trentbikes]

Sometimes you have to do what you have to do. I've had to modify my header pipes to fit on my motorized bike frames and engines.

[@chrisross8003]

Tidy job, looks like such a good fit in there

[@cro-thehacker7018]

As someone who made a ccr2000 mini bike here's a few tips. That 2 stoke exhaust is restricting it, you need to make a custom pipe for any low end / top end power. Switch to a torque converter, running a clutch requires such a high stall rpm that you'll be ruining clutches fast after good tuning and from my experience these engines run hot, so I have a rich fuel premix.

[@bbob5050]

you just commented one hour ago that’s wild. i’m currently working on doing a build like this so i will take your word on the torque converter.

[@andrew4403]

Good job buddy You do good work. Watching this because I got snow blowers I want to take the motors off and put it on something like a mini bike. Keep up the good work and I'll keep watching.

[@greenbassboosts8872]

I found a snow blower in the trash yesterday with a 2 stroke, electric start even! Pretty cool. Runs too, just really beat up. I'll be scrappy it out and taking the engine.

[@pwned960]

nice fab work, I've been watching cars and cameras for years and you are right up my alley! got another sub from me

[@CineMotoYT]

Thank you! Got a lot more cool projects in the works right now aswell!

[@whathappened2230]

You did a good job on the mini bike!

[@NOAH_HINMAN]

hey love your video don't stop keep them coming

[@thedancingpickle6362]

nice job man! I think we need more two stroke mini bikes

[@miguelpagansr6128]

Can't wait for the final product, thanks for that.

[@3613jeremy]

I wonder how hard it would be to install a snow blower engine on a razor quad

[@riccardojohnston9516]

Clean 🧼 as hell man 🙌🏾💪🏾 just subscribed dope build can’t wait to see it when your done ✅

[@miguelpagansr6128]

Awesome build, it’s like the engine was made for it. I have a tecumseh 3 horse 2 stroke similar to what you have. Right now I just have it sitting around waiting to go on something. Can’t wait to see it when it’s done.

[@SpACeCruizeR2o3]

Love how u switched it up that frame is clean fresh seat your part of the RACETEAM NOW MAN💯✨✨✨✨

[@GroundGravel]

Nice video and build! Thanks for sharing!

[@JOEZEP54]

Nice fabrications in this build. Good work. Stay safe, Joe Z

[@M074503]

cool project, im gonna keep an eye out for snow blower engine now lol

[@highlightzilla9581]

Keep doing random builds and watch how fast u blow up thank me later see you at the top bro

[@heymanmotorsports49]

Helluva job young man Great content💪

[@farleytrading]

I did the same thing with a toro snow blower,worked good but the stock carb kinda held it back.I put a huge old mcculloch chain saw motor on it and it was really bad assed!

[@thecaptain6562]

Great inspirational video man! I'm planning on sticking a 69 polaris playmate 164cc 2 stroke in a 1972 Moto Skeeter 350 but need to find a proper engine plate or someone who can make me one. Cheers and keep up the great work!

[@3613jeremy]

Now this is interesting you can grab a 5-6hp 2cy snow blower that runs great for $50 bucks

[@paule.maurice1521]

Great brackets !

[@Turbski1]

wow what an amazing project, wish i had the skills to this like u, i want to do a 2 stroke dirtbike motor in a minibike! but have no fab skills or friends with any lol

[@phoenixarizona8441]

Sweet build now you need a Headlight and a taillight bike will be the perfect scooter

[@bpagan7781]

Very good and entertaining to watch for those of us who love this stuff. Looks like a little 2stroke zipper! Keep the content coming. I just subbed.

[@jamest.5001]

I found a lipstick in the floor board of a car, used it to make gaskets like that, just rub it on the flange and stick some paper or something on it, then cut where the lipstick is not at, wipe off, or use as a template to make more,

[@shrop]

Very nice build, dude.

[@ogbigtsbikesandstuff887]

Great build!

[@BonFiredUp1]

nice build , i also too use a snow blower engine the Tecumseh 9hp 320cc four stroke 1994 with some port work & a 26mm carb it`s gone easy 55mph

[@g4lines197]

Can hit 55 on a 125 pitbike engine it will cost about $200 Same hp

[@BonFiredUp1]

@@g4lines197 we are talking Mini Bike Engines WITH NO GEARS, no cheep china pit bikes plz

[@LeviPeters.]

I have a craftsman snowblower engine on my fat cat mini bike, the drive shaft spins constantly while the engine is running. Curious why and what I’m doing wrong. Won’t it melt thru the belt if the bikes not moving?

[@derekcollins8621]

Im using the same engine for a build , and having trouble finding a clutch that fits. 3/16 key and 1 inch bore. Anything i order off Amazon even in the description it says 3/16 but theyre all 1/4 inch keyd. What clutch or modifications did you do?

[@Hoggdoc1946]

Nice job.

[@tdog1461]

Awesome build!!! I have a similar to 2 stroke engine from a snowblower. I was going to do the same thing.

[@inshallah4280]

Sweet build I would have extended the exhaust slightly past the seat to keep as much heat away from my butt.

[@howardkey6152]

Man if I had some fabrication skills I’d be all fuckin over this type of build that’s so cool

[@phenny1]

I don’t🤷🏾‍♂️😂 I just did a predator swap for the first time over the summer tho on a Coleman. Wasn’t too bad so imma buy a smaller frame on marketplace and use the old 2 stroke snow blower motor we got out back. Idek if it run im starting from SCRATCH. Wish me luck bro🙏🏾🤣

[@howardkey6152]

@@phenny1 aye you got this dawg

[@MrPatrickStephenson]

Cool build

[@eddielord145]

Use a Higher stall clutch so the motor can rev up

[@sdugasjr]

Could just swap the springs too instead of the whole assembly

[@CineMotoYT]

Good idea! That thought didn’t even cross my mind, thank you

[@seanmckay3392]

you might need a bit smaller of a rear sprocket though and maybe a torque converter

[@Bigbull6069]

Hey bro,I have 3 of those Toro 2strokes- 1 is a Brigg's,the others are a Suzuki/Toro,third is a Yecumseh .Whhat carb and jetting did you use?🤔

[@Bigbull6069]

I also have exhausts and carbs for Yamaha kt100's ...what ya think ?

[@cmd8718]

What carb did you use?

[@TWLML420]

My mom had the same snowblower back in the day

[@jafar4502]

Good build and it’s different 💪🏽

[@CineMotoYT]

Thank you! What should I build next?

[@ProjectRipper]

Love it nibbi carb tune and a ported jug she would send so hard

[@motorlife5239]

did you know if you take a harley davidson trans and put it on the minibike that minibike will have 6 speed 2 stroke engine and trans and itll be EXTREMELY fast especially with that expansion pipe on it itll out preform a yamaha YZ250 100% love the build buddy

[@SNELLERIZED]

Your exhaust flange is WAY too thin. Otherwise, nicely done!

[@CineMotoYT]

Thank you, there is always room for improvement on the next build!

[@LULOPPASTOPPA5STARWRLD]

is it possible if you could drop the links into the tools you have if possible? it would be very much helpful & I would be highly appreciative 🙃✅

[@LULOPPASTOPPA5STARWRLD]

Tools wise, like the welding equipment & just overall how to build it.

[@Kingjulian-]

i love it i put the same moter in a a 140cc crotch rocket

[@yungBitta291]

My dude did this last year but a bigger snow blower 2atroke engine

[@lyricalmadness9026]

Nice stuff

[@mr03mach12]

Great build I like it 👍🏻

[@CineMotoYT]

Thanks for watching!👍

[@petemartus8876]

U can weld Dat forsure

[@2stroke_Smoke]

What snow blower is that engine off of? im now trying to find a 2 stroke engine that will fit on my mini bike.

[@shaunjoiner732]

Ive got the same motor he used and it runs good if your interested

[@2stroke_Smoke]

@@shaunjoiner732 what is the motor so i can look more into it

[@jeffallen6937]

I've always wanted to know more about adapting clutches to random shafts. How or where do you get adapters?

[@aaron7520]

With a lathe anything is possible

[@CineMotoYT]

Like Aaron mentioned below, with a Lathe/mill anything is possible. This engine used a 1" shaft. However the crankshaft is currently being machined down to a more common 3/4" shaft. I will go into more detail in the upcoming part 2 video!

[@zaybotv204]

Y’all need a 37 back there i have one I get up to 58 mph

[@seanmckay3392]

nice expansion pipe

[@shaunjoiner732]

What carburetor did you use?

[@shaunjoiner732]

@cinemoto

[@Bstallday89]

516$ now 😂 before shipping

[@James-ux5kv]

Did this in about 1973 with an 11 horse arien. Just saying.

[@joeplotz]

can someone tell me what kinda carb this is?

[@CineMotoYT]

I used a Mikuni VM24 style carburetor.

[@joeplotz]

@@CineMotoYTalso can you send a link to the first clutch u with with the 1 inch bore because i ordered one and it came with a 1/4 keyway and i need a 3/16 keyway

[@zekekearns9801]

Part 2 wya

[@CineMotoYT]

Just waiting on powder coat shop, Have a few more videos in the works now!

[@ryanrangel71]

Nice

[@colemantrailslayer]

That’s so cool .

[@MrBluekid117]

Easiest video I've ever watched in 2x speed.

[@Flavorsonlyyy]

WhAtwS thefatty pipe off???? Polling 50cc , If you had another I'd buy it get yu to fix it to fit my 2 stroke bicycle kit

[@190SkyTeam]

Polini

[@howardkey6152]

What model toro did you use?

[@CineMotoYT]

The snowblower was aToro Ccr 3650

[@yesIamDJjr]

its cool but the throttle is rattling so bad get a new one of there

[@matthewbishop8219]

I have one of those motors. Delete the governor!

[@racingdreamz8021]

cool project but looks super slow

[@CineMotoYT]

35mph is definetly not winning any races lol. My next mini bike build I'm working on will be way faster. It may or may not be a twin cylinder 2 stroke....

[@racingdreamz8021]

@@CineMotoYT Do a Briggs world formula build

[@bryanrose2384]

I have 2 500 cc 2 stoke jet ski engine if anyone wants to make an offer I don't want them

[@bryanrose2384]

There inside the jetskis right now u can get those as well

[@cro-thehacker7018]

Jetski's are pretty junk because the only place you can use them is on the water and no one does really does custom water builds so ykyky. You cannot flow enough water trough them to keep them cool unless it's a huge rad so

[@bryanrose2384]

@@cro-thehacker7018 u make no smece