How to modify fsia6b receiver to get battery voltage telemetry

[@magneresjuan]

Hello ! Great vid. I conect oposite voltage baterry to my fs ia6 receiver AND saw smoke... any ideas for the repair

[@PeterAbt]

Do you know if there is any way to turn of the Voltage Alarm? Because when I have my motor on - full throttle the voltage drops down quiet drastically - so low - that the alarm goes off. But I want to keep the high- low-voltage settings so that there I can keep the beautiful battery animation at the top right corner of the display. Besides that: Thank you for the video was a great help and works flawlessly!

[@feltav5719]

After this mod can you still get altitude telemetry as well as the rx voltage?

[@anhntcover7971]

Simple, concise, awesome 😆

[@k1ortia]

Just buy the £3 FS-CVT01 Sensor. plug and play in 5 seconds. job done

[@DLM517]

THANKS.

[@DLM517]

what country coinage is it as my keyboatd doesn't have it, thanks.

[@jimstewart6720]

Looks pretty risky......I bought the sensor!

[@rcbuildmaster6192]

Nice info , but I think we get flysky voltage sensor which can connect to ibus sensor port directly on FSIA6B

[@yashsoni7137]

It will distroye your rx

[@jc_fpv_ec]

function for 4s battery ???

[@mush0847]

The specification shows 4.2 to 6.5v max, but 11v battery can be used?

[@dominikap.7399]

What parameters to set on the transmitter for the 11.1V battery? How much for low, high and for alarm? The alarm rings even at full battery.

[@kickfliph]

Hello there, I'm trying to replicate the mod, so far I have made the cuts for the pin, in the front side, and in the back. But when I measure with the voltmeter I still have continuity, I scraped all that I believe makes the connection to the other pins in line but looks like It's still connected to the others. My board is like your brown color and not green as I see in some others videos posts, is that make any difference? I should do something else for this model/version board for the mod to work?

[@hoath99]

I think I have the same board as you, at the reverse of the pin, cut right into the corner on both the vertical & horizontal board. When i worked this out it cut continuity for me.

[@demodelbouwloods987]

how much voltage can it handle? can it handle a 6s battery?

[@harrymoman2682]

is putting wire from charging plug actually putting any extra volts into the reciever , i did this mod and just removed the power cable from my ppm cable and just ran the wire to the charge plug on the single cell , therefore i can use low voltage alarm on my remote , so thats only putting up to 4volts into the reciever , not the 12.6 you are ,,, also the cut and wire mod from the resistor to the cut pin , what is that actually doing as i never did it that way... thanks

[@technoroid]

Hello, do you know what is lowest voltage and highest can be monitored? I plan to use 6S LiPo and want to keep up with voltage monitoring, will it work? Thank you in advance

[@TechIdeasAG]

It's just simple, whatever battery you use just use 3s to the receiver, you can easily get it from your battery's charging connector. Hope you understand.

[@finleeover]

@@TechIdeasAG Thank you. I understand.

[@marinaartandcraft8662]

Bhai mere pas ek transmeter hai jisme 16mhz crystal laga huaa hai jo programmable nahi hai. Ye kis resiver ke sath binde karega.

[@Baz4antify]

Awesome video! Thanks, I'm going to make this modification!

[@ashishpawar2261]

Great video, it's working perfectly, thanks for such informative video

[@yashsoni7137]

When i give it power a theer face black ic which placed between two yellow ic is heating too much

[@SimjimX0]

Hello nice video How do you cut the wire to the rx fsia6b please?

[@melvi8834]

the video is not very good as it does not show at all well where it needs to be cut. I managed to make this change which is not very simple and not for everyone. I repeat the video does not show at all well where to cut in the part below.

[@DLM517]

No comment!

[@SnePra]

Nice Video 👌 But please make a video on monster amplifier... Can you make ?

[@prajvalbs8787]

Will this work for 4s , will it burn on 4s , please reply

[@TechIdeasAG]

It'll damage getting very hot

[@prajvalbs8787]

Ok tq

[@prajvalbs8787]

Can i use 3s

[@Typcio22]

Great!:) Are there any problems that this modification can cause?

[@yashsoni7137]

Problem nhi pura rx ki ma bhen ek ho jyegi dont try this

[@DemoPwr]

I appreciate the info...cheers!

[@Infinitymotivation]

Amazing

[@TechIdeasAG]

Thank you

[@FliteRC]

Kuch receiver me problem to ni aae gi na

[@TechIdeasAG]

No problem, better use 7806 regulator

[@fatihkamalak6575]

Bunu yapmanizdaki amac neydi

[@DLM517]

don't do it and i did and a ton of headaches. I just made a 4 AA together at 5.7 volts and got it bonded with a Flysky 16X.-1a6b

[@yashsoni7137]

😭😭plz help ne anybody have solution to restart my rx

[@f0xvibes]

Buying a new one will work

[@tryingtomake9871]

useful thinks

[@MuhammadTalha-in3ws]

Thanks waho

[@sinongsium193]

sip

[@yashsoni7137]

😡😡😡it is distroyed my fs i6 reciever

[@DLM517]

Mine too!