Revealing My F100's ALL NEW Engine Setup!

[@kalebholt]

I love seeing how far the channel has come over the years. The number of parters you have with this build alone goes to show that you are doing things right.

[@Thecraig909]

Thank you. I really appreciate that!

[@clevelandmaker386]

@@Thecraig909 how much does all that cost? And can I put that in an Edsel!?

[@JaredR1996]

My favorite vehicle on the channel hands down. I love this truck

[@stevebankuti9336]

nothing wrong with being above the deck by about 5 thou, your quench will be so much tighter so less chance of detonation,love the channel and sbf are my favourite engine as well

[@luther250F]

Other than needing .050 to the head for stretch. Fuck it.

[@stevebankuti9336]

@@luther250F He is using forged piston so much less expansion and heat transfer of the piston also using a forged rod which will eliminate stretch, he could easily go 5 thou above deck and use a 30thou to 40 thou cometic gasket, flame travel will be much more efficiant which leads to better combustion less deposits, more hp and longer life,just my 2 cents, im an aussie and we love pushing our motors to the limit without hurting them, my 302 68 windsor 40 over has stock crank .5.4 rods custom acl pistons,ported 302 iron heads with chevy valves heavily ported with 56 cc chambers, piston sittin up 5 thou above deck with a sce 30 thou head gasket.custom Acl flat top forged pistons a aussie crow solid flat tappet cam 540 lift 235 duration @ 50 on 108 lobe sep 11.1 comp and it screams to 7k no problems

[@luther250F]

@@stevebankuti9336 I’ll bet she’s kissed the head.

[@stevebankuti9336]

@@luther250F nope had the heads off about a month ago for a freshen up no damage at all in 6 years

[@stevebankuti9336]

good engine building is all about math and quality parts

[@gagepool4175]

"Like ya Cut G"

[@bennetfox]

From what you have said and the parts you have shown, this is going to be one spicy little 302! I am so excited to hear this thing run and to see how quick your F100 becomes!

[@wendlormsby]

It will be a 307 due to the .040" over bore. My 351 windsor's stroke is .50" and .040" over bore for 408 cubic inches and brings a ton of torque and wild H.P. to my poor rear tires on my '68 Mustang GT.

[@blueman5924]

Looks like a slick build. Stoked to see her rip ‘n roar again. 🤙

[@jonlennon3348]

If this engine develops problems I would seriously buy a Dart block And their 9500 series crank or steel.

[@nickwilkin5979]

This setup is going to be so sick. I'm a newer subscriber, but going back and watching how far this truck has come is amazing. I started for the Fox (I have an SN95 with the 5.0), but this is becoming my new favorite.

[@johnsarian_cu]

Seeing all those high quality name brand parts beats any Christmas unwrapping I"ve ever had by a mile!

[@Jarritos440]

Can’t wait on the crew cab lift! Looking forward so I can lift my f100 on 37s!

[@SAM-eg7jg]

I was confused back when i did my first motor and was so.. And still am all about the tune.. People would say to me, Sounds Good..! Me thinking they meant the Tune. They would then follow up with what kind of Exaust do you have..? Took me awhile to learn that some people are about the SOUND and Thats about it. I had no thought in mind for what it would SOUND like when researching the build.. I was all about the best combo. not commenting on your build just rambling,, Really like your vids. Carburetors are your best friend..! Learn to tune them.. !!

[@Xarmy187]

I can't wait to see this build. A high RPM windsor is going to be so bad ass! Makes me miss my old Windsor's. That being said, after all the issue's you've had, all the work, the cost of all the machining, man hours, etc. I don't think I'd do this build myself. my opinion. A coyote swap would probably be about the same cost, all said and done, and make similar power. I hope I'm wrong, and this Winsor makes almost 600hp. A very sick build, and a much better "cool" factor then a coyote swap for sure though.

[@RobertJohnson-lb3qz]

Almost twice the hp as cubes... Nice.

[@bobmanzi7712]

That's some technical stuff you're talking there. Great content thanks I look forward to the rest of the build

[@jackbarker59]

I didn't hear you mentioned a blocked girdle I would highly recommend.

[@mikemullay5622]

I like the Miller Lightning. That is how I would have built it.

[@AntaliveDM]

Getting inspired to get my second block and start building my boost ready bottom end. Good stuff

[@kennethchapman9564]

He didn't do anything to the Lightning that can't be undone. Vehicles are expression of the owners taste wether anyone else agrees or not. I've owned quite a few classic muscle cars and not many of them remained stock. However I didn't cut up the bodies or chassis or floors or threw away any interior pieces. I built a 428cj with domed TRW pistons, high lift/long duration solid camshaft, Mallory ignition. Ran on aviation gas and drove it to work fairly often and very reliable. A long duration camshaft will not produce as much vacuum for a booster for power brakes. Hydro boost solves that problem.

[@UglyHatchbackNismo]

The F100 is what got me started watching your channel. My son absolutely loves this truck.

[@OurCabinInThewoods]

Man this is cool can't wait to see and hear it run.

[@waynegouin939]

Hi Craig. You should build a 351 Windsor.

[@W5rr2nG]

glad you went with a anderson cam. theres a couple guys on here running them in foxbodys, and they are the $hit. nice build. cant wait to see it done.

[@shawndemeter3836]

I definitely appreciate all the work your putting into this truck honestly it's reignited the fire I've had for these old trucks, I do have a question for you though 68 f100 351w 4 speed short step bed 5500 good buy??

[@jessewilliams2990]

If it isn’t rusted apart and runs and drives it’s a good deal

[@shawndemeter3836]

@@jessewilliams2990 pa truck was a daily driver story kinda gets me in the feels, guy selling it isn't able to drive anymore due to agent orange

[@robertwells6454]

Lightning 4+4 is 🔥 Really Cool. 🤟😎

[@ICEignition]

Super excited to be involved with this one - except we thought the mullet would hang around!!! Great to see some progress Craig.

[@pjayhammond]

When are you going to go back to working on both the galaxys

[@benharper1682]

encouraging me to build my 70 SWB very similar to your 71. I am still looking for a Style Side bed (fleet) for mine. BFH

[@zekeharouff6983]

I can’t wait to see and hear this back together. That cam. With the exhaust setup that you had is going to be beyond wicked!! I’m sure I’ll see after this video, but hopefully you’re not changing the exhaust setup.

[@mma88cms]

For rags during the rebuild process, use commercial coffee filters. Economical lint free rags. Learned that from a MAK Diesel SME.

[@ltsgarage7898]

So you are a stock 302 stroke with a 40 over piston. You sure have some nice parts that are going into the block & on it.

[@LoneWrencher]

i let the machine shop put mine together while they had the block.only costed a couple extra hundred for the piece of mind it was worth it,no problems in over 5 years!

[@randallmason9687]

My local machine shop will only warranty the engine if They assemble it. Only few hundred more. Worth it!!

[@LoneWrencher]

@@randallmason9687 if your going to use top shelf parts why not let a professional put it together.i know doing it yourself is good content for your channel,but screw that,i want my engine done buy the best builder-machine shop i know of!

[@gordocarbo]

@@LoneWrencher True...put the ego aside if you got a bunch wrapped up in it esp on a high rpm build. There are certain tricks the machinst will know most dont to making a high rpm engine live. Paid mine to assemble mine due to that...was only a few hundred and spent plenty on the best balancing job I could get...did the clutch, fw too. With a cam of 82 deg overlap it is still as a corpse at any rpm. Love it

[@JF-hm4yv]

love it! can't wait to hear this thing run!

[@elliottandrade9336]

love to see the channel growing! side note, i had a mullet for over a year it felt weird!! i bet the back of your head was cold for a bit huh😂

[@Rick11231948]

So....is the 4 link truck frame for sale...you seem to be avoiding it

[@finerthingsinlife4494]

8 on 6.5 beadlock is super common. every jeep and crawler run them when u go 1 ton axles.

[@johnnypdoesthings]

Scat makes great rods, they’re also the only company that still makes rods for the 4.7l sohc v8 from dodge.

[@jaredearl6767]

Truck is going to be sick! Honestly I think that red would look pretty good on it, I may have missed it but it’s not possible to run an adapter for those wheels you already have?

[@fredclements6843]

You can do all that stuff now Craig a wife an kids will put the breaks on a lot of fun things.😂 I’m just now getting back like I was when I was your age ! Now I got to much stuff going on now an can’t get anything finished 😂

[@randycarolsmith1437]

Keep up the amazing work. Out of all the trick stuff going on this build. Who else thought that water pump is best lol 😂 i want one now

[@jasonpetrich4141]

So are those like the bfg km2s. Cevlar reinforced ?? Those were good tires, but I like the triple tread style and 6ply soft compound of boggers, the side lugs bite hard I'm in super soft mudd all the time. PNW!!!!

[@landonlarkins]

i have a quick fuel 750 on my 383 and my god i love it. it screams

[@speedyg2577]

How many engines have you built and you finally realized the main bearing tangs are different. No wonder they blow up. Smart idea but use the rev limiter cuz the one in your head is not working.

[@cwbintn8949]

Having the iron block and heads will help a lot with how hard you drive your rigs lmao

[@John3_16Q]

Steel wheels with caps on old fords is best

[@jasonmyers3847]

I just bought a '64.5 Mustang as a rolling shell. I'd love to buy one of your 302's.

[@mahon055]

Looking good Anderson cams are awesome

[@GabiWhite-qr6lz]

Last time I dug those c clips out of the oilpan, think bout snap rings, think kieth black hypereutectic,( spell chek) come with snap rings.

[@sleepinggiant90]

Stoked for this build!

[@TerrinLee]

What compression ratio did you end up with?

[@jaircr4ft237]

Love this build, currently planning this same build if not similar with a forged crank plus a few other goodies, one thing I can’t seem to find anywhere (this is my first build), what rod and main bearings do I use? Which ones do you use? Need a 2.123 rod journal and 2.249 main journal, help! Thank you!!

[@jaircr4ft237]

Also what wrist pins do you use?

[@gilfernandez9122]

Great content! Looking forward to your next video putting the engine together!! 👍👍

[@max_archer]

Can't wait to hear this thing run. I might be taking a few notes, definitely want something with a high-revving SBF with that NASCAR scream for my next build, just gotta decide what car to put it in. (Mustang would be the obvious choice but it's kinda boring, but it's gotta be something that'll be fun at a trackday or canyon.) Those trophy truck wheels are sick btw, I'd be seriously tempted if they fit my last-gen Ranger. I'd have to powdercoat them though, wouldn't look good on my Race Red truck.

[@colejohnson5447]

The Fairmont could be appealing to you. I’m pretty sure they were built on the fox chassis and they had small blocks!

[@thegraystang66]

Cant wait to hear that new setup with the blackwidows!

[@GabiWhite-qr6lz]

Summit sells beadlock kits, maybe 4 wheel parts.

[@Fredmullegun]

Gen 1 lightnings are pretty valuable now. probably a bad move.

[@trashbandit2449]

Yeah I don't really see the point of starting with a lightning just to redo all of it. Sounds pretty expensive

[@Fordcertian]

Interested in those beadwork rims

[@davidcatlette9697]

How about do some body work on the crew cab ? And those rims “ sick “ is you word but I would trash them ! And how do you get out of speeding tickets ?

[@richheider8455]

Hutch's Welding does a beam kit for your truck with an option for coil overs and look for wheels @ U.S. Wheels 🤔

[@pnwchris2000]

What was the ballpark price point for everything that you’re throwing into the rebuild? Lots of very solid and reputable companies.

[@claeslindgren2704]

Oh no first the stache and then the mullet 😧 The only haircut I’ve ever missed is my bleached purmed mullet

[@Z3CHYD]

Were you still planning on frame swapping the F100 to that other frame you did the crown vic front end and all that other work on? She's a sweet build regardless of course!

[@gordocarbo]

Better grab it those are tough to find and usually sellers want tooo much

[@young11984]

Guy said..my kids love it...nobody else matters at that point. I do thread in front plugs and drill an .018-.025 hole to pressure feed the timing chain too

[@lollipop84858]

You know they make an installation tool for those piston pin clips, ate..

[@bandog6391]

I get my F100 Camper Special in July can't wait to get it..

[@bandog6391]

@@lilorbielilorbie2496 mind is a true camper special it even has a special red badging on it

[@shandyellis-brown8091]

new to the channel, mostly a buick family, but i do have one 87 fox, 37k stock... love the channel....great work.... def gonna get a shirt for my 16yr old daughter... shes a huge car chick! Tennessee here. you coming to ford fest here at bowling green?

[@AnDrEw122100]

Man you can talk , great content . Just discovered your channel.

[@STR8SICCC]

*The Miller Lightning kinda makes me sad, but also happy*

[@pmodd]

Good to see progress, both the block and your hairdo. The mullet was terrible.

[@gordocarbo]

7000 rpm motor youre gonna lean on. Solid lifters every time man really slims down the chance of failure. You may wanna pay them to do the bottom end at least. Not that you cant but there are certain things a machinst will do to make it live when they are spun up that high. Killer balance job do the FW and PP also even if they are already "balanced", Youll thank yourself later.

[@hankfink]

How is that Quickfuel carb plate holding up? Keep seeing those things melting!

[@mmg6282]

Got yourself a big boy hair cut! No disrespect! Anxious to hear that 7000+ RPM small block, Ford brother. I’ve always kind of wanted to do a short stroke big bore small block Ford. Not really for the horsepower just for the stupid fast revs and crazy high RPM. I like what you’re doing, I like the fact you’re bringing Ford to the four front regarding performance I was born a Ford guy I’ll die ford guy. Maybe it’s just KZbin and more exposure but it seems that Ford is becoming more and more popular with the hot riders

[@RicoCantrell]

I'm excited. That truck is going to be sick.

[@Heatshieldproducts]

Punk Rock Racer in the house!

[@hendo337]

Surprised you never build 9.5 decks, so much more ci, 393,408,418,427,434 roller 351w block makes so much more sense than 306,331,347. Once you add legit heads like TFS 11Rs, single plane, 950 carb, 600+hp is cake.

[@diyjeff1838]

Let's get that quad cab done!!!

[@booncha1971]

Great video as always !

[@JP-jq1qx]

Maybe I missed it, what amperage is the alternator going to be to drive the fans and water pump?

[@kingdick9488]

Ya and lay out how you did your 92motor❤ also, because I love That motor

[@marksearcy9708]

Cool off to a good start!👍

[@jafejfaya7064]

Where can I get a carb insulator plate like yours? If u don’t mind dropping the link

[@jeffrey4547]

u sure have put a lot of money in this truck my 68 chevy i have 2000 in it and have a 4 inch stroke 454 with heavy rods heavy pushrods steel crank high flow heads pushing over 500 hp but have a tunnel ram setup that i got for 100 bucks stock it had 450 hp then a 02xx 400r turbo that is good to 800 hp stock has the heavy 8 bolt pump heavy clutches stage one shift kit factory built 12 bolt possi power steering power breaks factory have full factory gauge cluster with tach new tail gate rebuilt suspension all painted just need to finish the interior have full movement electric heated black leather seats out of a land rover oak wood bed with new chrome strips plus still have the rebuilt 327 and 400 turbo that came with the truck 2000 counts on buying the truck too. my 70 high boy i have 350 in it with a 390 and a 428 to rebuild but runs ranger xlt with tool box on side clean rust free truck with dana 60/80 lockers got a 70 motor home with power steering power breaks rose etched interior trim full gauge cluster with tach cruise control wiper delay ac desert cooler radiator and a tilt wheel all will bolt right on the high boy got the motor home for free

[@edcadlick2650]

I can't wait until it fires up😆👍

[@GrampysGarage]

Whatever happened to the process of plasigauging bearings? Is that done anymore?

[@Green_Sasquatch]

I will watch your videos no matter what you post

[@gatalino84]

Was this 302 a roller block ?? If it was a retrofit what lifters did you use ?

[@davideldridge2537]

All those parts in a stock 2 bolt sbf block ar 7000 ?

[@mikemullay5622]

When you do the build on the crew cab please don't cut the fenders.

[@ambrosebrower8760]

I disagree. Please cut the fenders.

[@johnsadventures5753]

What size brand and specs are the cam love the sound

[@alltherpm]

Never heard of stock block 8000 plus build, my engine builder would not put his name on that, I guess this is y there's no blocks left, there race blocks

[@rynohough6200]

Nice valve covers wil round this baby off

[@DanzigDemento]

The haircut makes you look like Officer Pete Malloy from Adam-12!

[@dylanromine4101]

As far as I know they still us I beams on for cab chassis truck to this day

[@Truck_person]

What if your buying an F100 with a 429 BBF scat stroker kit but not looking to actually race in it just to cruise

[@klintsweat8168]

Check out battle born brakes for the 4wd swap on the crew

[@Fordcertian]

What block is that one for sale

[@michaelchalk4262]

Hey Craig when is the Ford Galaxy coming back

[@prestonwolff1141]

What's a realistic power estimate you think this motor will put down to the wheels in the f100? 450?

[@thaddeusw5072]

How much does that whole setup cost??

[@joshuas9483]

I have a 69 gt Torino that I’m putting a 302 in but when the day I blow it up I’m doing thisss

[@alltherpm]

Must b Cleveland heads going on with these rpm goals

[@brandonfloyd6321]

Try putting a complete engine from a lawnmower trailer up to a engine stand. Lol lifted front of engine and kicked board under it. Then do the rear the same way. Kept doing that until it was like 10 boards high front and back. Pretty sketchy 😂😂