Thanks for watching the AR637T Programming Series! If you have any questions, please leave a comment! Like, Share, Subscribe, and ring the notification icon so you never miss a new video! Tune in to Air Marshall Monday's - Every Monday at 8PM Eastern! Have a great day!
@florianleonhard4 жыл бұрын
I have the DX6 Gen2 and the ar637T. in forward programming first set up the message appears" connection failed" "click for menu". I can not get into the programme? Could you kindly help. Best, Florian
@TheRCAirMarshall4 жыл бұрын
Do you know what version of firmware you’re running on your DX6?
@scottmarcum25694 жыл бұрын
You made this so much easier than even the Horizon Tech did. Thanks for doing this series much appreciated. I now feel comfortable flying my model.
@dlm55363 жыл бұрын
Really clear outline with the spectrum tx on screen and great commentary thank you
@DavidsTV Жыл бұрын
I'm so confused. What app is this you are using to program the transmitter/receiver? I can't find this ap anywhere.
@Cadillacstsv064 жыл бұрын
Another nice video in the series Dave! Thumbs up! Cheers!
@darrell33684 жыл бұрын
Love your show and learning a lot thanks for sharing ps God Bless and be safe ,wet in South Georgia today can’t fly but catch all the shows and learning all I can.stay. Dry and safe
@thomasmilano97964 жыл бұрын
Thanks for the videos! Been using my extra receivers following your programming tutorials. Is the envelope just like intermediate mode where the model has limits but does not return to level flight?
@TheRCAirMarshall4 жыл бұрын
Thomas Milano yes, that’s correct!
@jtepsr3 жыл бұрын
when i finished forward programming, safe was working but when i switched to as3x, safe was still on. what did i do wrong. i assigned switch A which is normally a gear channel.
@jimmydell93703 жыл бұрын
Dave I've watched to the best of my ability but have been stumped ! My NX8 TX switch B doesn't switch between Flite modes, inside fwd programing. My Rx is registered & updated along with my Tx. I have tried factory reset, then step by step, I'm lost at this point. Thanks for your help in advance.
@jtepsr4 жыл бұрын
So after first time setup, you can go back and make changes to those flight modes?
@warrenmassey40294 жыл бұрын
Please can you explain how to unassigned a gain channel so you can utilize all 6 channels and still have AS3X and safe assigned to a switch
@garykopecky95782 жыл бұрын
What would cause my flight controls to be exactly opposite of what they should be in Safe. I am using a ix20 and and a Spektrum 637T. The aircraft control throws are set up to spec and respond exactly as they should until I turn on safe. When safe is enabled the controls react exactly opposite as to what they should. I set the modes as you suggested. Also is there a way the return to Safe first time setup and start the programming process without a complete factory reset of the receiver? Help.
@TheRCAirMarshall2 жыл бұрын
SAFE responding opposite of the flight controls would suggest that the receiver orientation is set incorrectly. You definitely want to sort that out, as it will also have an effect on the way stabilization responds and result in a crash. The only way I know of to get back to the first time safe setup is to reset the receiver.
@garykopecky95782 жыл бұрын
@@TheRCAirMarshall Thanks again for your insight. I guess I fat fingered something in the Tx during the set up. Your suggestion about reorienting the receiver in the Tx worked like a camp. All flight controls respond as advertised. Sincerely Gary
@grischafario3 жыл бұрын
Hi Dave Congrats for your amazing videos, explaining complex things in easy words 😀 I still have a question concerning flightmodes (FM): I want 3 Rx FM (the same as you show - AS3X off, AS3X on, SAFE) to be changed with a three position switch on my DX9. But I also want 5 Tx FM (launch, cruise, thermal, speed, land) for my sailplane, each with different mixings, flaperon positions and dual rates, selectable by two three position switches. Will then each of the three Rx FM be applicable for each of the 5 Tx FM? Thanks for your help, Daniel
@florianleonhard4 жыл бұрын
I have the DX6 Gen2 and the ar637T. in forward programming first set up the message appears" connection failed" "click for menu". I can not get into the programme? Could you kindly help. Best, Florian
@octane20993 жыл бұрын
When I turn on safe and do my turn for my approach I can’t bank it and turn like I do with the AR636 receivers I have to turn it off line up and then turn it on is their a way I can fix that would I have to set it to envelop?
@TheRCAirMarshall3 жыл бұрын
No, it should work in self leveling/angle demand. When you say you can’t bank it, what exactly do you mean by that? Is the plane just staying level and the wings won’t bank at all when you’re in SAFE mode?
@octane20993 жыл бұрын
@@TheRCAirMarshall when I turn safe on It won’t bank much can I add more banking on safe setting
@jerrywillfong57704 жыл бұрын
Great information
@jamestennant-eyles98704 жыл бұрын
Hello Dave, thanks again for another brilliant episode. I am just wondering what your overall opinion of the advantages of the AR637T are over the AR636? I can see the setup can be done directly with the tx, (although that doesn’t look that simple to me), and that there is the option of up to ten flight modes. However I am very happy using the Spektrum Programmer, and don’t think I need more than three flight modes. Is there any other advantage, particularly when it comes to actual flying? All the best, James.
@1peanut4 жыл бұрын
thank you for your great videos. i learn so much from you.
@insurancemann14 жыл бұрын
This looks way to complex for me to setup. Hopefully v2 will be a little simpler. Love the concept though.
@TheRCAirMarshall4 жыл бұрын
David Wilson it’s not as bad as it looks. I just like to be as thorough as I can. Once you get it in your plane and figure out what’s going on you can program the receiver and have it fully set up and ready to fly with all features enabled in 10-15 minutes.
@chksix4 жыл бұрын
Love your videos and your dedication to the community.👍 Wanna be friends? lol