Wooden boat rebuild: getting ready to PAINT and run the ENGINE! - Sailing Yabá 144

Bringing Yabá from wreck to dreamy! Episode 144
In this episode of our boat restoration, we start painting the hull of our boat but the weather decides otherwise. Besides that, we also get our engine ready to finally be tested inside the boat!
👉 SUBSCRIBE to not miss out on the new episodes:
bit.ly/3dI3hBn
YOU CAN SUPPORT OUR PROJECT:
👉 By becoming a patron - join to unlock exclusive content:
/ sailingyaba
👉 Through Paypal donations:
bit.ly/3kR4Ezo or [e-mail]
👉 By wearing our products:
shopsailingyab...
👉 GET OUR FAVORITE TOOLS:
www.amazon.com...
We are forever grateful to everyone that is living our dream with us ♥️
🇧🇷 Legendas em Português em todos os episódios!
🇪🇸 Subtítulos en español en todos los episodios!
💙 Who are we?
We are Ben and MP!
Recently we decided to purchase a two-masted wooden schooner in Brazil. The fun detail about our story is that the boat we bought was sinking and relying on many bilge pumps to survive so we had to lift it onto the dry to start a full refit. Once the boat was lifted (for the first time in her life) we realized that the work needed was much more than expected. Between bailing or accepting the challenge, we decided to go for the second option. Watch us as we bring Yabá back to life with the help of an amazing team of traditional shipwrights, sharing every phase of the process, overcoming the highs and lows and having fun along the way.
More about us:
👉 About us + Q&A
• What does MP stand for...
👉 more info about the project
www.sailingyaba...
💙 Massive thanks to our amazing team of carpenters that never let us down and continue to amaze us at every step of the process: Toninho, Zeca, Hélio, Claiton, William, Nezo, Nico, Adilson, Beto and Luiz. YOU ARE LEGENDS!

[@schwabrichard9829]

M.P. now i know why you are the chief engineer of the YaBa. You are a perfect fit in the engine room!🥰🥰🥰

[@clivewilliams3661]

Fibreglass exhaust wrap is readily available from motorsports outlets in rolls that are just wrapped on and fixed in position with stainless steel bands or jubilee clips. There will be heat given off due to its thickness but it accommodates different shapes well. For a 'permanent' installation you could use a Rockwool insulation that is specifically formed in pipe halves and clamped together with an aluminium or stainless steel sheet casing. This will give a surface that you can touch without fear of burning as well as it acting as sound deadening. You need to talk to heating installers as its used in boiler rooms for flues and steampipes. Lastly, you could get the pipe ceramic coated in any colour that you want that acts as a heat barrier, please check on the anticipated surface temperature. As a last and probably an overkill precaution I would fit a sheet of aluminium to the woodwork above the pipe with a space of say 12-15mm above it to allow air flow. This will deflect any heat off the pipe and precvent the wood getting hot..

[@WikkedDonkE]

This ^ ^ ^ is great advice. I'm thinking you'll probably want to go with the fiberglass wrap. It's identical to the stuff you removed from the engine originally, minus all traces of asbestos. The heat shield might actually be a good idea because the exhaust is quite close to the floor beam and it's right off the turbo exhaust outlet. Wicked job on the boat!

[@NAMCBEO]

I AGREE, CAN'T ADD MORE👍👍👍

[@giovannirosa968]

Rockrool is the best, same product used in oil refineries and oil process platforms for insulating of high temperature pipes. Insulating this piping is important because if it is not well insulated, the temperature inside the engine room can rise and overheat the engine and even cause a fire, even with the cooling system running.The problem is that there is little space between the ceiling and the pipe, you would have to check the thickness of the insulation layer to see if it fits.

[@juusol989]

THERMO-TEC WILL HELP YOU FIGURE OUT WHAT YOU NEED TO PROTECT YOUR PARTS AND PERFORM BETTER.

[@moosesamli4569]

Make sure you soak the wrap in water before starting to wrap the pipe and use stainless wire or stainless zip ties to hold the wrap tightly in place. Also get a turbo blanket from wither a truck or Motorsport supplier. I can recommend Demontweaks for all items.

[@wonderwond]

mp is so beautiful, always makes me smile to just see her smiles

[@saylaveenadmearedead]

I would paint the pipe with high heat paint to reduce rust before wrapping it up in heat barrier... so cute how much she loves fondling her pipe.

[@aucarreau]

Ben & Maria Paula you are SO awesome I cry every episode! Ben, be proud of the 'ugly Betty'! 😭🤗❤

[@SailingYaba]

That's so sweet! Thank you so much for the love!

[@69woodburner]

Agree with the exhaust wrapping comments and a metal shield spaced slightly off the deck beam. I think you will need to put antifreeze in the cooling system, not because of freezing but for corrosion protection. The dissimilar metals will cause a lot of corrosion to occur if you don't use some sort of coolant in the system other than just water.

[@manolisgledsodakis873]

And also to raise the boiling point.

[@beilno2890]

@@manolisgledsodakis873 Antifreeze doesn't really increase the boiling point, that is done with pressure.

[@mikhem1962]

You bought a boat that you really knew nothing about. Now you both have detailed knowledge of every inch and aspect of that boat. Your life on it will benefit so much from this.

[@lawrencetrapani5623]

A good roller and brushes for your large volume painting, in my opinion is a better choice for wood boats! And the time it takes to tape and protect the other areas is time consuming. And.........when you are on your travels, good brushes and rollers etc. Can be on board for touch up and you can be anywhere! PS have been a wood boat guy for 60 years. And in my old age still take specialty work to this day! And Yes! I LOVE WOOD BOATS. Live Aboard and cruiser for over 15 years. Sure wish You Tube was around then. I generally worked on boats and cruised and worked on boats from destination to destination. AWESOME LIFE! Regards and Lots of Smikes and good thoughts for All boat lovers and owners who Live their Boats

[@johnmaliskey7951]

For the exhaust you need to check out high-end motorcycle shops. There is a fiberglass tape/wrap used for motorcycle exhausts to protect the rider's leg. There is also a high heat glue used in the door seals for wood burning stoves. This can secure the wrap in place then use a stainless steel wire to make sure it doesn't slide. Second........... A heat shield is needed between the overhead and the exhaust pipe. It keeps a space open for air to circulate in between the overhead and exhaust pipe. It can be 14-16 inches wide and 18-24 inches long and usually stainless , centered on the closest position of the pipe. This is similar to being code for wood burning fireplaces to protect the wall and celling in houses here in the U.S. ............................. enjoy

[@COLLAR01]

GET PIPE WRAP FROM SUMMIT RACING, THEYLL SEND IT TO YOU GUYS

[@Tomm9y]

Lots of good advice in the comments and so important to follow. A safe and durable exhaust system is vital.

[@thechaplain9906]

While acquiring my Bachelor of Science in Marine Engineering & Technology we used REFRASIL PRODUCTS, i.e. “Refrasil Cloth, Refrasil Woven, Refrasil Rope Gaskets, and Refrasil Sleeving on the exhaust. Good Luck 👍 I’m quite impressed by how far the two of you have come!!! God Bless You & Keep You…🙏

[@johnharris2337]

You have room for a muffler there, a used truck one would do, it will make your mental tranquility sooo much more! Engine room envy here. X

[@Maxdekriek]

great update guy's ....thank you so much 😉😊 greetsz from friesland......max.....💛

[@SailingYaba]

Thank you so much Max! 🤩

[@stephenmurray9850]

There is pipe wrap you can buy for heat shielding from any car parts or motor cycle store , just follow the instructions, pretty easy. The main thing I want to say is please put anti-freeze additive in your water in the engine. It increases the boiling point of the water and helps with stopping corrosive scale and sludge build up in the cooling system (especially in the heat exchanger) It also helps track down coolant leaks because the water is a different colour. Thanks for the video.

[@dennisdatu6464]

Love the easy vibe background music.

[@goodevins9408]

Hope Australia is on your sailing destination list so I can view those beauty in person

[@lookronjon]

Header covering for the exhaust loop. It’s a wrap for car exhaust. I use it on the hot rods I repair and build. I’ve put it on my motorcycles too. It will cut down on heat and will prevent being burnt if you touch it. It comes in rolls. They make different widths also. I have used old fire station hoses in the past too but I think that’s what was on there originally. If you do that just wrap a heavy aluminum foil over it to contain the fibers. Looking good. Thanks for sharing your progress with us.

[@jopac6614]

🤩can't wait to hear Yaba snore

[@96biggss]

I would recommend that you install an aluminum heat shield above the exhaust as it is too close to the floor above and will cause a fire. Exhaust wrap will help but not enough.

[@hoosierpete]

As a former mechanical insulator my number one choice for the exhaust would be a Ceramic Fiber with a Satanite Refractory backing, than wire it on with bailing wire, ceramic wool is the best heat resistant fiber out there. You could also use rockwool.

[@nickviner1225]

Don't forget to check the level of your engine oil just after first start as you will not have filled the filters before you you start for the first time. I know you said it holds five litres but to be safe check again.

[@SailingYaba]

Most definitely!!

[@johnnunn8688]

5 litres is the g/box. The engine holds more.

[@rodnelson8110]

Hi MP, don't forget to recheck the oil after running the engine, some of what you put in will remain in the filter and needs to be replaced

[@miguelreina7824]

ya sele ve el fin, para disfrutarlo, gracias

[@mallyuk1]

Really good job that exhaust bed is called swan neck to stop rush of outside water rushing in and is also above water line

[@SoBoring136]

Guys you must support the exhaust with a vibration absorbing bracket at the top of the loop. If you don’t it will crack around it’s engine mounting point. Looking good exciting times for you both.

[@JesseBlair]

You can get the wrap for your muffler, from any hot-rod car shop.. its a fibreglass based cloth that you wrap around the muffler, make sure you wet it lightly before wrapping, the heat from the muffler will form it. Love your videos!

[@danaskubic2145]

So the boat is red, thanks for sharing. Whoops, wrong boat, thanks anyway, your getting a lot accomplished.

[@hairyferrit]

Get the highest temp wrap you can afford. Never know when the engine might run too hot due to problems so you always want the best rating you can get.

[@kevine.phillips7578]

Good morning favorite KZbin folks! We hope the weather cooperates more. We know it can be disappointing and stressful but you have great attitudes! You’ll get her painted and it will turn out great! Closer and closer!

[@SailingYaba]

Thank you so much guys!!

[@kennethd.cooper5252]

Nice work both of you. You really should put a heat shield between the rafter and the exhaust where it bends. I know there are some exhaust wraps that will help, but I wouldn't touch it when it's running cause it's still going to be warm. Check with a mechanic or exhaust muffler shop for a wrap and shield. Be safe stay healthy enjoy your week.

[@77RB77]

Yes I agree wrap and a heat shield

[@bobuncle8704]

So looking forward pto hearing the engine run

[@michaeldallimore8590]

Like others have stated you can use a fibreglass exhaust wrap that should be readily available from automotive and motor bike accessory stores. It is very effective. You can use large stainless steel hose clamps at either end to make sure it does not unravel.

[@eddygonzalez6018]

As mentioned before, Refrasil is the brand of a high quality thermal insulations that comes in a variety of forms. Blanket, tapes, rope, sleeves. They are safe and graded to hold a continuous running temperature of 980 to 1260°C. Often used for industrial insulation. I would consider it.

[@vanDeudekom]

The best advice......yes Sir!

[@Laarth]

Classic insulation is mineral wool or glass wool. Easy coverage is aluminum tape.

[@andrewforbes146]

i so love that table great job

[@craigmcdonald4737]

exhaust heat shield tape is what you are looking for!

[@robertbuterin4142]

I work in a shipyard and usually the pipes are thermally insulated with a layer of stone wool and then strips of cloth soaked in gypsum are wrapped around wool.

[@simonaldridge82]

Inhibitor required for fresh water in engine a real must asap. Looking good getting very close to launch. Little more patients it all comes together in the end.

[@SailorAllan]

I love that MP is ALL over the mechanicals of this build--you go girl !

[@BarnacleBilltheSailor]

Just remember that if your engine oil filter is new, you may need to add more engine oil after you start the engine and your oil circulates through.

[@rohantherockwiththerocketh7871]

Cool you're getting really close to being able to splash Yaba. Have a ripper you guys!

[@robbyoliver4953]

Well as I have watched since you guys bought Yaba. I can say I look so forward to every Sunday to see the progress of this rebuild. I and in the beginning, I said, I don’t know how they expect to pay for this. And I don’t understand why they take on such a huge project. But now I have watch every week I can say, I am excited for you guys. And can’t wait to see the final project before launch. I know if it was my boat I would have a huge party on launch day. And christen her with a bottle of Champaign broken over her bow. I feel after such a life this old boat has had, she deserved this rebuild. But at the same time I really don’t think I would have done it, but I am 60 years old and you guys are young. Would love to know when you launch her what it cost for this rebuild. The wood alone probably cost a fortune. But wow you 2 have learned and have done so much. What a great job you 2 have done. MP is a good mechanic, good job girl on this engine rebuild. Ben your rebuilding and planning skills is been genius.

[@richardchiriboga4424]

A really productive week!! We are getting closer and closer to the water!!! Thank you for my Sunday morning coffee with Yaba!!!!❤

[@SailingYaba]

Thank you so much Richard!

[@richardbedard1245]

If you don't get that boat painted soon, the suspense is killing me, I'll come down there and paint it myself!!

[@drewduncan1541]

Titanium fiberglass exhaust header wrap is what you are looking for.

[@loribagley3555]

Thanks!

[@fw1421]

I hope that hose from the pump to the oil pan is certified for use with oil. Oil and rubber don’t work well together. The rubber hose will swell up with time and start leaking. Not something you want happening when you are miles and miles from shore. You might consider installing a piece of sheet aluminum to protect the deck brace above the exhaust pipe. That and the fiberglass wrap should protect the wood well enough.

[@pinkladybikermamma3603]

LOOKING MIGHTY FINE

[@TK-zx1wi]

Ceramic blanket would work really well here and thdn you can wrap the blanket with fiberglass cloth of your choice

[@stvooplayhouse]

Love I'm getting so excited.❤

[@ronkanoff]

Great work

[@jbostondesigns]

So for your pipe covering look at motorcycle exhaust pipe wrap… it’s fiber glass and works on Harley Davidson Exhaust pipes… also look for it in Automotive under headed wrap tape

There are woven insulation tapes made from Basalt available for the layer directly contacting the exhaust pipe. beyond thoat tape you can go with a mineral fibre insulation and then an outer layer of fiberglass.

[@77RB77]

The stuff to wrap your exhaust is the same stuff used on automotive headers. I think it's fiberglass. Love the videos you guys are an inspiration

[@dcallan812]

Both of you have learnt so much, Ben with his welding and MP with the whole engine system. Yaba will be in safe hands .2x 👍

[@SailingYaba]

Thank you very much!

[@johnnunn8688]

Thought you said, ‘wedding’, phew!

[@lonner98]

Looking good.

[@davidorourke5795]

Kiln builders use spun silica wool which is a high temperature insulation material which can be installed using the same method as would be used with fiberglass wool insulation. The advantage is that you could put your hand on it when the engine is running and the pipe is at full temperature.

[@ssmith5650]

MP ! There’s just no way around it You are adorable!! Ben great problem solving solutions on the welding! Boy you two are on the final stretch 🤗

[@tonychin5065]

The ceiling on top of the big pipe should be protected with a piece of metal against heat and fire. That is what the car industry is doing when the exhaust pipe is too close to the car floor.

[@stuartheald7657]

Titanium exhaust heat wrap should do the job. It works on a manifold so should on that pipe.

[@FlyingConey]

When working with the angle grinder try to avoid getting sparks against the shield and safety glasses at all costs. Sometimes the sparks play ping pong and find its way inside the classes. Having glowing sparks in the eye is no fun. Actually I ruined two pairs of my regular glasses although I was wearing shield and safety glasses over them and I WAS avoiding the sparks. Just be careful, you only got one pair of eyes.

[@MikePoole-dx3cb]

Exhaust header wrap!!!

[@Tim8mit]

for the exhaust I would bet that the old ribs were thinner under the engine mounts.....every week you are closer to splashing....good work

[@charlesthacker4129]

This is made with k-wool, alpha cloth, and 0.003 stainless foil. It's an insulation blanket.

[@charlesdavis4396]

They also make a carbon fiber exhaust wrap. But I agree you need a heat shield from the wood.

[@steelboss337]

K-Wool insulation is what I would recommend. I laughed watching you remove the asbestos insulation. In the US you’d need a license, hazmat suits, full face respirators, dust mitigation, and special waste disposal.

[@tbd-1]

18:50 Header wrap. Used in aftermarket auto exhaust systems.

[@extremelydave]

That's an awesome 80's punk rocker haircut Ben!! It IS winter down there, so I would expect to see rain. And more rain. It's a good thing MP is such a positive influence here...she makes a cloudy day seem nice. Love ya MP!!!

[@bkvdpw]

Look for a product called "Exhaust Heat Shield". It's a fiberglass/aluminum/unobtanium wrap with a ceramic insulator that comes in various widths and lengths and is attached with stainless steel ties. The product is manufactured by a company called Heatshield Products and is available from several online distributors. Heatshield Products also have a KZbin channel with an installation video. And Ben, when describing an end-product of your welding, you should always end on the high note. It's not functional . . . but ugly; it's ugly but functional. See how much more enthusiastic that sounds? :) LOVE your videos!!

[@SailingYaba]

Thank you so much!! I had the misunderstanding that every heat protective tape had asbestos in it, that's why I was trying to find something else. Now I know they can be made with fiberglass only and that's a huge relief! You're so right about the order! We will keep in mind your suggestion about always ending on a high note. What happened in this case is that Ben didn't feel comfortable only saying good things about his Frankenstein considering its looks 🙈

[@joeracer883]

I was going to say the samething. Its used on exhaust headers as a tape rape. Its just like what they had taking off.

[@johndavidson6867]

Getting closer to being able to go chase some waves.

[@kellymendonsa6442]

Great video as always, if the exhaust has changed that much that you had to cut and reweld it you may have problems with the prop shaft lining up also . You may want to look at that soon so you're not surprised later. 👍

[@adon214]

For the exhaust i believe you can get feet of header wrap for hot rods and drag strip cars. Jegs is a company that sells the stuff.

[@kerryverity963]

I’m amazed every week with the skills that you both have acquired!! They will come in handy in the future. You’ve had the most talented teachers along the way!!!

[@mikejacobs9449]

Amazon has similar items and marine grade exhaust heat shielding and exhaust wrap. Love the channel

[@derekraine7933]

you people are makIng a fantastick job of Yaba please put the guards back on the angle grinders or you will have no fingers to steer her with All the best from Cumbria UK

[@koningbolo4700]

18:48 Motorcycles (old school ones) use a fibreglass woven band (webbing in Dutch) to wrap the pipes...So look for Pipe Wrap Tape or Band... The tape is designed to go on the hottest part of the exhaust system...but to be safe I would do at least a double wrapping and use the second layer of banding to fasten a couple of stainless steel mounting brackets (strips of stainless) so you can mount an aluminium heat shield or several around the hottest part of the pipe. To be extra safe I would put a piece of cement board on the the ceiling beam right above the top of the siphon, just in case... The rest of the exhaust pipe I would either single wrap or use hose clamped heat shields.

[@Maxdekriek]

i am sure the engine will start and run like new!!!!😁😉😊😘

[@SailingYaba]

Let's hope for that!!!!

[@Maxdekriek]

@@SailingYaba let's do that.....🙏🙏🤗

[@dennisg8164]

Lots of KZbin videos on fibreglass wrap 😊

[@renatomedina6595]

São Pedro manda no tempo. Basta rizar as velas e tomar um chamarão.. que passa😂😂😂

[@LastChanceTinyHouse]

Bandages and plaster on the large piping like putting a cast on your arm or leg, about a half inch thickness should work.

[@gregbolitho9775]

Thanks

[@marktanska6331]

I have been watching you since the beginning. To see Ben become a competent boat builder is a joy to watch. I was sure you would not make it. But now...... all power and respect to you. I built a 52 foot 30 ton ketch from plans. I know what it is all about.

[@SailingYaba]

Thank you so much Mark! This means a lot to us!

[@waltercadwalader5754]

Wrap the exhaust in Ceramic Wool and cover it with woven aluminum.

[@waynehelsel3949]

You should put some sort of exhaust hanger on there

[@danaowen9014]

Any time you prime or paint, make sure you make wider strokes, with your gun, other wise your starting and stoping more often, and more likely to have runs.for your table legs, you can use tubes like is used in a camper, table.

[@michaeleast4849]

There is a aluminum covering for exhaust and turbs look up heat shield for exhaust.

[@Zeeeeeeero]

My guess is the exhaust didn't fit because the boat has squat/squished some being on the hard and/or due to expansion and contraction of moisture content in the timbers, likely a combination. Really love your project, I'm feeling the anticipation build! Much❤!

[@TheH-Dfamily]

I just tagged a link to Amazon for exhaust wrap, I have used it on many projects works great. They have black or a tan color.

[@hardwaydave6636]

For your closed cooling system. you need to replace the water with an antifreeze solution. I'm sure you just used water for leak testing. but after you get everything shook out. drain the water and punt in a coolant that is rated for your system. Take a minute and research this. Very important, due to the environment and dissimilar metals within you cooling system.

[@jamesbaldwin7676]

Hope you find an insurance company willing to write a policy on an older, wooden vessel. Some form of liability insurance is nearly a worldwide, marina requirement. Even older live-a-board fiberglass vessels, are becoming increasingly harder to insure. Whatever you do with your exhaust system may have to pass a safety survey.

[@dubie2470]

Motorcycle exhaust wrap !!!!

[@fredrik7012]

Install a bunch of fans in the engine room!!

[@TairnKA]

I suggest a heat shield be added between the exhaust pipe and beam (gaps on both sides. ;-) There's "header wrap" for cars, but I don't see why it couldn't be used there?

[@HerrOveSweden]

The exaust bend is a water lock. It prevent water to run back to the engine.

[@johnnunn8688]

Which is exactly what they said.

[@idreecemian2192]

Yet another very informative episode on Yabá, putting together an episode in such an interesting way takes lots of insight to bottle a weeks full of work under half hour frame despite the 90, 7, 3 strain, hats off to both of you, love your work

[@casketeir]

Ceramic Wool will work to insulate the exaust pipe.

[@johnchaffin5494]

Some hotrod header wrap for the exhaust for the exhaust pipe, I think it's fiberglass and heat retardent.

[@TexasRaised68]

Look for header wrap at a speed shop, cheers!

[@jackrichards1863]

The bin lining stuff. As you charmingly refer is called polythene sheet, I think? You guys might get exhaust wrap from truck supply stores or car parts retailers. I suspect the modern stuff does not contain any asbestos.

[@virago41]

Rockwool for exhaust pipe It's inert and environmentally friendly 😊👍🙏🇮🇳