WORST RUST REPAIR I HAVE EVER DONE! - MASON DUMP BODY REPAIR - PRIMEWELD

  Рет қаралды 100,459

MCF WELDING

MCF WELDING

Күн бұрын

A rust repair i would like to forget. Got it done and on to the next one.
WELDING LENS I USE -
www.rod-shield...
SAVE 5% PROMO CODE - MCFWELD
INSTAGRAM - / mcf.welding
Wanna send me something?
MCF WELDING
95 WEST MAIN ST
STE 5, BOX 167
Chester NJ 07930
Check out some of my other videos!
Subscribe and like for more welding
To get in contact with me - mcfwelding@gmail.com
#welding #weldrepair #snowplow #migwelding #stickwelding #landscape #contractor #fabshop #rustrepair #plowing #newjersey #dumptruck #cummins #diy #cuttingtools #plasmacutting #trailer #truck #dodgeram #grinder #sidehustle #sidework #primeweld #mig180

Пікірлер: 196
@peterfrazer1943
@peterfrazer1943 Жыл бұрын
As a Ship Repair Welder for 35 years, I have seen plenty of rust. You did a good job. I have subscribed and will enjoy more of your vlogs. All the best from the UK. 👍👍
@mcfwelding
@mcfwelding Жыл бұрын
I appreciate it!
@OFW
@OFW Жыл бұрын
I really hate doing repairs with a lot of rust, but someone has to do it. Nice job!
@justinsousa7624
@justinsousa7624 Жыл бұрын
Rust and Railings the two jobs that I despise.
@mcfwelding
@mcfwelding Жыл бұрын
Do you see rust like this in Cali? Here in the north east 1 out of 3 dump trucks look like this lol
@anytractorman
@anytractorman Жыл бұрын
I did a similar truck. Cut out the whole floor. Welded a nee one in. Crappy work the box needed so much more but thats what they wanted.
@mcfwelding
@mcfwelding Жыл бұрын
always the case
@AlwaysBored123
@AlwaysBored123 Жыл бұрын
I can't believe you did all that with a grinder and a bench vice. Tremendous work hope you got paid handsomely for it.
@mcfwelding
@mcfwelding Жыл бұрын
Had to get done that's the only way I feel I could have done it with the tools I have
@WelderB1Family
@WelderB1Family Жыл бұрын
Thanks for this upload!!! I have some rust repair to do on my Econoline Van 🤙🏿💯👨🏾‍🏭💰🔥
@mcfwelding
@mcfwelding Жыл бұрын
Rust ain't no joke lol
@ajsironworks3937
@ajsironworks3937 Жыл бұрын
Ok. You painted it hot. Was thinking you’re slipping. Nice gold chain Jersey welding man you did great!!!
@mcfwelding
@mcfwelding Жыл бұрын
Always gotta get it when its hott
@neilheriot2361
@neilheriot2361 Жыл бұрын
You can also clamp a piece of length of angle iron to your work table to use as a break.
@chrishamblin2774
@chrishamblin2774 Жыл бұрын
You are a Great welder don't shortchange yourself. Be Blessed
@chrishigdon1070
@chrishigdon1070 Жыл бұрын
how about some rust converter before you weld it up, that will help the box.
@mcfwelding
@mcfwelding Жыл бұрын
under this was pure ROT, i dont thing rust converter would have helped in this case
@TheIronDuke502
@TheIronDuke502 Жыл бұрын
Hello From Mark In Kentucky. I recently retired after nearly 32 years of welding/fabrication at a state government equipment repair facility where I worked on many of the rotten truck beds. I have found that the slicer wheels on a grinder was probably the best method of cutting out the “Crust” and which the other material that used to be metal was no longer metallic. In fact, The Cutmaster 102 would absolutely not cut some of the worst areas and I would have to either use the slicer wheel or melt it out with a OxyAcetyline cutting torch. A good deal of my repairs on the Galion beds that we had was repairing or replacing the top section of the bed which was usually tubing and as you did, also welding in the bottom section which luckily for me was not rounded like your project. Our newer Galion beds had flat brackets welded center ways between the front and rear of the top section of the bed which really helped strengthen the sideboards. The brackets that I used to make to help the older beds that I was working on were 1/4 inch flat with the bottom of the plate for example being around 10 inches long and the top being around 8 inches long which had a nice look to it. The tallness of the brackets was usually relative to the height of the sideboards. Our facility used to purchase at least 3 inch thick rough cut oak lumber from local sawmills for lumber and for the tandem dump trucks and 2 inch rough oak for single axle 2,1/2 ton trucks. The Mig wire that I used was either.035 or .044 Lincoln L56 copper clad wire using a MillerMatic 350 welder. I would love to have a dollar for every inch of Mig wire that I burned repairing those junky beds. I honestly can’t say that I used exactly the same techniques for every bed repair; Because One Size Does Not Fit All when you are doing the welding repair thing. Take Care My Fellow Welding Friend.
@clcare5563
@clcare5563 Жыл бұрын
Then you wouldn’t get repeat business 😂
@brianfairchild7819
@brianfairchild7819 Жыл бұрын
nice job. been there done that, but i had to replace the tub too. good to have a local shop willing to bend it up for ya
@mcfwelding
@mcfwelding Жыл бұрын
A big help to have that piece bent first
@brianfairchild7819
@brianfairchild7819 Жыл бұрын
@@mcfwelding had my local shop bend the curved sides of the tub, uprights, and rub rails. Wish the rest of the truck was in as good a shape
@scottysutherland3568
@scottysutherland3568 Жыл бұрын
Thanks for the video. I got my 2 year ATA in welding and have been in the field working for 5 weeks now. So in my head, im still new for the next 2 years at least with all the knowledge out there, thanks for sharing yours!
@marleyboy7732
@marleyboy7732 Жыл бұрын
Great job...When my old employer found out I was a welder for 5yrs (now a 22yr truck driver)..He wanted me to repair his trucks but keep me at my same pay. He was so cheap. Be a driver & his welder?
@mcfwelding
@mcfwelding Жыл бұрын
Up charge that welding !
@pqworks9019
@pqworks9019 Жыл бұрын
Awesome work! That was a very high quality repair and it turned out super nicely. Good job!
@mcfwelding
@mcfwelding Жыл бұрын
Thanks really appreciate it
@job38four10
@job38four10 Жыл бұрын
If you do lot of grinding and welding, consider a 3M Speedglas Adflo welding hood, lens never fog up and your lungs will love it......... Good repair job, all that truck needs now is some NH Oil Undercoating.......
@curtisroberts9137
@curtisroberts9137 Жыл бұрын
Vulcan flux core is pretty good wire. I've used a lot of it with good success. Tried some other cheap flux wire and had lot of porosity problems. Flux core is so much more expensive because of the manufacturing process to make tubular wire filled with flux, but you also do not need to pay for gas so it evens out quite a lot in that regard. As you noted, it is far superior for dirty aplications to solid wire mig. Nice work. It's too bad the owner does not want to do more work to repair more of the structure but you can only do what they are willing to pay for.
@buelowexcavating
@buelowexcavating Жыл бұрын
The worst rust repair is a rust jacked double frame repair, that had about 3/4" of rust between frame rails. A friend did his, he removed the box, cut off the hinge bracket, removed the two rear axels, springs, cross members and a few other things. It looked like too much work for me to do. I called a shop for a price to do it, they estimated about $20,000. I got rid of my truck that needed that work. I now look very closely for rust before I buy a truck.
@charlesloar3210
@charlesloar3210 Жыл бұрын
Have run the Vulcan Flux Core wire a lot. Runs very well. Nice saving the $$ with a good product.
@marcuscicero9587
@marcuscicero9587 Жыл бұрын
great work. imagine you musta been thinkin "well if this ain't puttin spats on a pig"
@mcfwelding
@mcfwelding Жыл бұрын
i certainly was the whole time
@jdtvco
@jdtvco Жыл бұрын
Great video thanks for stopping by the other day also!
@mcfwelding
@mcfwelding Жыл бұрын
Thanks nick, always got the good tools
@anthonymarino4260
@anthonymarino4260 Жыл бұрын
great job. well done
@mcfwelding
@mcfwelding Жыл бұрын
Appreciate it
@c50ge
@c50ge 2 ай бұрын
Cut two slots in a 2” piece of heavy wall pipe, secure the pipe, start bending, keep bending. Until you like it. (Learned from Bondo Billy)
@theessexhunter1305
@theessexhunter1305 Жыл бұрын
From the UK, done lots of that but always liked that type of Jacket you are wearing.
@ricardojano3716
@ricardojano3716 Жыл бұрын
Crust covered it's gone Underneath is going going soon to be gone
@mcfwelding
@mcfwelding Жыл бұрын
most likely..
@Genx4
@Genx4 Жыл бұрын
Good job doing what the customer asked of you to do.
@MulletmotoKC
@MulletmotoKC Жыл бұрын
Hard to see from this angle but the drive rollers, if you’re using the 030/035 side then you leave that facing out. It looked like you turned it in which would be the opposite of what you needed for that wire
@mcfwelding
@mcfwelding Жыл бұрын
maybe i did, not sure. but it welded fine lol
@scrapperstacker8629
@scrapperstacker8629 8 ай бұрын
Great video!!! Living in the north east you see lots of trucks looking that way. I gotta start leaving business cards on them.
@mcametals.mikelilly7931
@mcametals.mikelilly7931 Жыл бұрын
Nice job from an old tin knocker!! Great channel. I just bought my first Primeweld using your recommendation. So far so good. I’m guessing your a fitter….did I guess right? Have a good one.
@mcfwelding
@mcfwelding Жыл бұрын
Yup, steamfitter. Glad you like the videos. Would be nice if primeweld gave me a kick back 🤣🤣. Either way I like machines. They are great for a home shop
@alb12345672
@alb12345672 Жыл бұрын
Saw this and said this upstate ny rust. Then I see Monticello on a sticker🤣🤣
@mcfwelding
@mcfwelding Жыл бұрын
haha trucks from jersey the beds are built up there so it alread comes pre rusted haha
@Freedomfabrication777
@Freedomfabrication777 Жыл бұрын
Those Rusty Repair jobs are up there on my list of dislikes. You did a good job for what you had to work with!
@mcfwelding
@mcfwelding Жыл бұрын
Was a tough one but I think it came out okay
@gillihansmobilewelding
@gillihansmobilewelding 10 ай бұрын
Rust is gold here in Florida but don't ever work on old concrete trucks around here. Haha, the rust is under all that white coating and it's EVERYWHERE!!
@jeeperjeeper2956
@jeeperjeeper2956 Жыл бұрын
Cheers from Iraq. Loving your work 👍👍👍
@chriscarroll3204
@chriscarroll3204 Жыл бұрын
Really enjoyed watching
@robertoobregon3750
@robertoobregon3750 Жыл бұрын
Flux core wire has it's use and not all flux core wires are the same. Started using E71T-GS then used lincoln NR-211MP and currenly using hobart 21b.
@manoeldias-m9t
@manoeldias-m9t Жыл бұрын
Dope -Hats off
@evanfrucht
@evanfrucht Жыл бұрын
Most people arent willing to pay what it takes to actually do it right. Sometimes you take their money anyway...
@alisciamarotta3888
@alisciamarotta3888 Жыл бұрын
Looks like a landscaper salting truck! What did the other side looked like? Nice little job....been awhile since your last post.
@mcfwelding
@mcfwelding Жыл бұрын
believe it or not this truck actually never plowed or salted ever in its life. just a spring summer and fall rig, guess it didnt get washed or cleaned out often
@gillihansmobilewelding
@gillihansmobilewelding 10 ай бұрын
Bro, these comments are where the pros live. I extra love it when they say they would turn down a job instead of getting paid twice and having a repeat repeat repeat customer. 😆 You can tell they don't actually weld when they come with that bunk shit. The customer will always want to paint their turd a few times before doing what really needs to be done. MFs screaming safety must not ever leave the house... or have insurance. 🤔
@mcfwelding
@mcfwelding 10 ай бұрын
hahaha
@thejoey993
@thejoey993 Жыл бұрын
I love going through all my subscriptions and got tons of binge content of all areas of life😅 always reminds me of my time welding. Im only 30! 😂 but i make music now 🤙🎹 both skills demand patience and imagination in my experience
@CarlosGonzalez-bs6hl
@CarlosGonzalez-bs6hl Ай бұрын
How where you able to find bent metal the exact same... or how did you take a sample to steel supply to match it
@scottjune3554
@scottjune3554 Жыл бұрын
Nice work
@mcfwelding
@mcfwelding Жыл бұрын
Thanks scott
@chopperhehehe
@chopperhehehe 2 ай бұрын
Cracking job 😊 atleast a cple years 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿😁✌️
@Houstonruss
@Houstonruss Жыл бұрын
Damn that's a sight better good job. Were you running the fluxcore gasless or with something like 75/25?
@mcfwelding
@mcfwelding Жыл бұрын
straight flux core on this one
@scottysutherland3568
@scottysutherland3568 Жыл бұрын
Looks to be gasless, self-shielded
@davidfreed8050
@davidfreed8050 Жыл бұрын
Very cool! Nice job.
@mcfwelding
@mcfwelding Жыл бұрын
Thanks!
@neilheriot2361
@neilheriot2361 Жыл бұрын
👍
@thepagan5432
@thepagan5432 Жыл бұрын
I'll guess the rust will return pretty quickly, especially underneath where there was still rusty material. Rust converters are a good way to stop rust spreading. The repair looked ok.
@ммм-ч4е
@ммм-ч4е Жыл бұрын
Exactly! i write same massege. To sad whan spend so much energy ( for good work (
@mcfwelding
@mcfwelding Жыл бұрын
for a bed that is only going to be in service for maybe 2 more years, this was he wanted. and will last for that time
@thepagan5432
@thepagan5432 Жыл бұрын
@@mcfwelding Well as long as the customer is happy that's all that you need. I've seen some beds which would make people cry, honest. Using a torch and sledge hammer to remove individual panels and parts of the superstructure as well and welding plates in, where the weld looks like something a bird dropped. 👍
@yota87truck
@yota87truck Жыл бұрын
Cool project!
@mcfwelding
@mcfwelding Жыл бұрын
Thanks!
@DarylGilbo-ci8xb
@DarylGilbo-ci8xb 2 ай бұрын
New welder here question why not use stick rod like 7018? Could You Even Stick Weld that?
@mcfwelding
@mcfwelding 2 ай бұрын
way to thin to use 7018
@jtlawnstoneconstruction9923
@jtlawnstoneconstruction9923 11 ай бұрын
I had the identical truck it was stolen back in 2021 it was a 96 5spd drive seat was well worn
@grumpyguys4082
@grumpyguys4082 Жыл бұрын
Looks a lot better than it did. Who makes that welding jacket?
@mcfwelding
@mcfwelding Жыл бұрын
Not sure got it from work they usually get generic ones in bulk
@medicbabe2ID
@medicbabe2ID Жыл бұрын
Strong work 💪
@lwwarren
@lwwarren Жыл бұрын
Time to take the money you make on 4 or 5 jobs and put it into a plasma cutter. You won't regret it when jobs like this comes up.
@MrBigtom06
@MrBigtom06 7 ай бұрын
You should use a piece of pipe cut in half for that upright piece
@mcfwelding
@mcfwelding 7 ай бұрын
yea, I should have...... but didn't have any
@serious2204
@serious2204 6 ай бұрын
This video brought me to your site, I like your welding . Great work. I,m thinking of buying a Primeweld mts 200, 3in 1 mig welder. I watched you weld panel in solid. Have you used your primeweld 180 to spot weld thinner guage sheet melal?
@mcfwelding
@mcfwelding 6 ай бұрын
Yea it can do that, you just need to set it up correctly and you will be good to go
@josesilva-nm5cc
@josesilva-nm5cc 11 ай бұрын
Probably you can’t use a piece of pipe split on half then cut the two ends with the right angle
@mcfwelding
@mcfwelding 10 ай бұрын
That's what I wanted to do. getting a small piece of pipe was the hard part though
@Xtx-dv7ll
@Xtx-dv7ll Жыл бұрын
great repair!!
@mcfwelding
@mcfwelding Жыл бұрын
Thanks!
@1978punisher
@1978punisher Жыл бұрын
Sand blast best way
@TheTreegodfather
@TheTreegodfather 2 ай бұрын
Bx-2230 Kubota in the background?
@baconpizza1239
@baconpizza1239 Жыл бұрын
Make a pipe anvil for bending metal.
@mcfwelding
@mcfwelding Жыл бұрын
not a bad idea
@lowrider9249
@lowrider9249 Жыл бұрын
Turned out nice, I would have welded it up the same way, flux cores the way to go being outdoors.
@mcfwelding
@mcfwelding Жыл бұрын
Yea mig would have been a disaster
@exwldr6945
@exwldr6945 3 ай бұрын
Nothing Solid left to Weld New metal to on that Bed! Plasma cutter Would be ideal for Cutting the rusty metal out . I'd Use Better quality Wire than harbor freight though.
@mrizquierdo89
@mrizquierdo89 Жыл бұрын
Looks great. How much did you charge for this job and how long did it take? I'm in NY as well.
@mcfwelding
@mcfwelding Жыл бұрын
Not enough lol
@davidshumway9639
@davidshumway9639 Жыл бұрын
I just started watching but they placement piece had so much ting when you handled it by the garage it sounded like gutter material (light weight).
@mcfwelding
@mcfwelding Жыл бұрын
It was 16 gauge, not to thick not to thin
@davidshumway9639
@davidshumway9639 Жыл бұрын
@@mcfwelding yeah I heard that later on on the video after I made the comment. So is that part of the bed supposed to be structural at all? You have to admit when you look at one, that section and those little uprights sure do look beefy. I'd never expect they were formed from such light duty sheet material. Was the original metal thicker and the owner just wanted it to be cosmetically improved?
@jthatguys
@jthatguys Жыл бұрын
Maybe a cheap sheet metal brake could bend that piece? But maybe not worth it if you aren’t going to use it often. Or spend the money on a press with a swag finger brake?
@mcfwelding
@mcfwelding Жыл бұрын
Thought about a small brake. Might get one in the future
@WayneAtkins-e8o
@WayneAtkins-e8o 10 ай бұрын
Try to run dual shield wire
@paulg5900
@paulg5900 Жыл бұрын
How did you make a template for a shop to bend the side strip up for you? I get carboard for shapes but idk how id make a template for someone to bend.
@mcfwelding
@mcfwelding Жыл бұрын
Cardboard and painters tape
@shannonlawsonnashville
@shannonlawsonnashville Жыл бұрын
I’m not really sure as to why you’re using flux core instead of MIG
@mcfwelding
@mcfwelding Жыл бұрын
have you ever tried mig welding rusty metal? flux core will weld better with not so clean of metal compared to gas mig welding
@shannonlawsonnashville
@shannonlawsonnashville Жыл бұрын
@@mcfwelding i have, but honestly, im not experienced enough to have known that. Was an honest question. Just curious
@scottysutherland3568
@scottysutherland3568 Жыл бұрын
MIG welding is similar to TIG in the sense that you always want the cleanest scenario. No rust
@thejoey993
@thejoey993 Жыл бұрын
​@@shannonlawsonnashville😂 you shouldve added a question mark bro
@dougpersell8776
@dougpersell8776 Жыл бұрын
Always fun trying to fix something that is to bad to fix been there done that you did ok.
@mcfwelding
@mcfwelding Жыл бұрын
I hear you on that
@officiallocogringo721
@officiallocogringo721 4 ай бұрын
👌
@juanrrobledo89
@juanrrobledo89 Жыл бұрын
Nice job, the owner could blast that rust off and then Rhino Line it, might help
@aopet7615
@aopet7615 7 ай бұрын
grinding make my eyes watery 2:44
@mcfwelding
@mcfwelding 7 ай бұрын
me too
@jacktimoney8546
@jacktimoney8546 8 ай бұрын
How do you charge for something like this
@mcfwelding
@mcfwelding 7 ай бұрын
charged by the hour. took me about 9 hours. your hourly rate will reflect your pricing
@americathefree3708
@americathefree3708 Жыл бұрын
Don't like the way Meltin Metal Anthony signs off! You did a good job!
@adammulcahy644
@adammulcahy644 Жыл бұрын
I don’t think meltin metal anthony gives a fuck what you think.
@bizzieballa
@bizzieballa 10 ай бұрын
​@@adammulcahy644pretty much😂😂😂
@dougbetty2008
@dougbetty2008 9 ай бұрын
Awwwww. He's a meanie!
@charliehuntsman9827
@charliehuntsman9827 7 ай бұрын
@adammulcahy644 . I would agree meltin Metal Anthony don't give know fucks😂😂😂
@runifuceeme406
@runifuceeme406 Жыл бұрын
WHERE DID YOU GET THE METAL SKIRT?
@mcfwelding
@mcfwelding Жыл бұрын
Custom made from the metal supply yard I use
@tayotaylor7897
@tayotaylor7897 3 ай бұрын
How much did that run you
@crj1249
@crj1249 Жыл бұрын
Did you weld up the Scores before installing?
@mcfwelding
@mcfwelding Жыл бұрын
Nope, no needed since it was welded around the whole outside
@crj1249
@crj1249 Жыл бұрын
@@mcfwelding Definitely needed. Why would you leave that Piece Compromised?!
@mcfwelding
@mcfwelding 7 ай бұрын
Hey come here and hit it with a hammer and see how compromised it is I will pay for your flight out.@@crj1249
@crj1249
@crj1249 7 ай бұрын
@@mcfwelding OK bet. When and where is the flight to?
@mcfwelding
@mcfwelding 6 ай бұрын
once you get to newark airport give me a call ill come pick you up@@crj1249
@Randall-fn7wh
@Randall-fn7wh 5 ай бұрын
Your painting looks like "The Welders Apprentice" the way he's paying attention.
@mcfwelding
@mcfwelding 5 ай бұрын
Huh
@noco3216
@noco3216 Жыл бұрын
Run like LH, uphill
@ммм-ч4е
@ммм-ч4е Жыл бұрын
bro u make greate job. But dont kill all rust. All rust come gain (
@richardcline1337
@richardcline1337 Жыл бұрын
Biggest problem I've seen is that you didn't treat the old metal underneath to prevent further rusting inside or at least slow it down. You really did not accomplish much except to slow down the inevitable by missing that one step.
@mcfwelding
@mcfwelding Жыл бұрын
Was not paid to do that. Brought it up with the customer, he said to not do anything other than what i did.
@richardcline1337
@richardcline1337 Жыл бұрын
@@mcfwelding so customer was just looking for a cheap and quick patch job rather than spend a little extra money to do things right. Sheesh!
@mcfwelding
@mcfwelding Жыл бұрын
@@richardcline1337 you'd find this hard to believe but alot of customers want things done cheap I don't like it but cash is cash and if he paid me my rate to this job and I'm happy with what I made on it, so be it. nature of the game
@richardcline1337
@richardcline1337 Жыл бұрын
@@mcfwelding, no argument there. It's going to cost him in the long run but it's his truck, so....
@stevepauley2437
@stevepauley2437 Жыл бұрын
Maybe he decided that was something he could do on his own, to save a little cash.
@chrishigdon1070
@chrishigdon1070 Жыл бұрын
good job mister
@Softtaildeluxe97
@Softtaildeluxe97 10 ай бұрын
Man I would have just used a pipe cut in half and cut to fit
@mcfwelding
@mcfwelding 10 ай бұрын
me too if I had some pipe laying around
@MrBigtom06
@MrBigtom06 7 ай бұрын
I said the same thing.
@mrquickspool
@mrquickspool Жыл бұрын
Where do I find the soundtrack music used?
@plaid13
@plaid13 Жыл бұрын
any late 70s x rated movie.
@mcfwelding
@mcfwelding Жыл бұрын
KZbin Music
@KarasCyborg
@KarasCyborg Жыл бұрын
Rust? Man that bed's got Cancer.
@mcfwelding
@mcfwelding Жыл бұрын
you aint lying!
@peterkelly9614
@peterkelly9614 Жыл бұрын
Terribly damaged by rust - the structural integrity compromised. But the steel patching creates a facade. The steel plate welded on is thin and add little strength. Truck later probably sold to some sucker - with degree of rust hidden. And they end up with a real lemon. And a danger to society.
@mcfwelding
@mcfwelding Жыл бұрын
Ok
@peterkelly9614
@peterkelly9614 Жыл бұрын
You are a good welder. Not criticizing you - I am criticizing the owner of the truck.
@danielvakulich8115
@danielvakulich8115 Жыл бұрын
Welcome to the real world bud
@peterkelly9614
@peterkelly9614 Жыл бұрын
@@danielvakulich8115 Yep. It’s ducked, isn’t it.
@thejoey993
@thejoey993 Жыл бұрын
When life gives you lemons...
@johnfarrell273
@johnfarrell273 Жыл бұрын
It's is only scrap
@jeepsblackpowderandlights4305
@jeepsblackpowderandlights4305 Жыл бұрын
Thats the worst youve seen ?... you must not see much..look at rusted out bed im going to rebuild and youll see what i mean
@mcfwelding
@mcfwelding Жыл бұрын
I've seen much much worse. This is the worst I have worked on.
@FlyingDutchman-th6nj
@FlyingDutchman-th6nj Жыл бұрын
Just cover the rust with a new piece ? Why didn't you do sandblasting? I wouldn't pay for such crap
@mcfwelding
@mcfwelding Жыл бұрын
well your view of this video just paid me so thanks champ
@FlyingDutchman-th6nj
@FlyingDutchman-th6nj Жыл бұрын
Continue with the videos. Did you learn the job in Pakistan?
@ProleDaddy
@ProleDaddy Жыл бұрын
​@@FlyingDutchman-th6nj TF, guy? Who shit in your Wheaties?
@JuarezDerrick
@JuarezDerrick Жыл бұрын
​@@ProleDaddy his boyfriend 🌈
@dannylim3318
@dannylim3318 Жыл бұрын
Here's a rule of thumb. Any structural part removed from that truck should be replaced by a part of same or better gauge steel. Nothing like that flimsy sh!t that was used. I have never seen anyone actually post something so bad. It's a safety concern, but also a liability concern. If that truck ever got into an accident, the welder could be sued for such poor work. But...the owner wants it that way. Well, the welder can always refuse this kind of job.
@mcfwelding
@mcfwelding Жыл бұрын
🤣🤣🤣🤣 what ever makes you sleep at night
@jaxithfox
@jaxithfox Жыл бұрын
They could only be sued if the accident was caused by failure of their repair. And even then it's not a guarantee that anything would come from it.
@scottysutherland3568
@scottysutherland3568 Жыл бұрын
​@jaxithfox in order to PROVE it was the welders fault for the failure is EXTREMELY difficult and rare. Without a fatality, there won't even be an investigation into it. The welding police do NOT exist the way so many people think they do.
@ronnieswindski825
@ronnieswindski825 Жыл бұрын
Though I agree it's a little thin and a thick piece wouldn't cost much more, odds are this truck belongs to some mехісаn who has no money to spare. That bring said, that part really isn't that structural.... when you go to dump, almost all the weight is on those two main inner frame rails. Considering there are countless mason dumps with the sides rusted off completely and in operation everyday, it doesn't even matter. Also, this isn't a triaxle dumping 27 tons, this little truck is rated for probably 1.5-2 tons. That's nothing not to mention probably half that weight is on the back hinge when going up...
@gillihansmobilewelding
@gillihansmobilewelding 10 ай бұрын
Love it when armchair experts come up in the scene with the real knowledge. 👌🏼
@eccentricsmithy2746
@eccentricsmithy2746 Жыл бұрын
Bed cant be saved, all you are doing is putting lipstick on a pig.
@bransonred1
@bransonred1 Жыл бұрын
And, thats basically what he said in the video.
@mcfwelding
@mcfwelding 7 ай бұрын
you are correct, but this is what they wanted so why not get paid bub
@scotty362100
@scotty362100 Жыл бұрын
Very painful to watch!
@mcfwelding
@mcfwelding Жыл бұрын
The job or the video? whats your angle here
@derwoodogrady4666
@derwoodogrady4666 Жыл бұрын
not hard to do at all.
@mcfwelding
@mcfwelding Жыл бұрын
ok cool.
@chrisacres
@chrisacres Жыл бұрын
You’re the reason I dislike most people.
@derwoodogrady4666
@derwoodogrady4666 Жыл бұрын
@@chrisacres awwww...pity,pity poop balls.
@peterking2561
@peterking2561 6 ай бұрын
@@derwoodogrady4666child
@KennethDix-xs9xn
@KennethDix-xs9xn Жыл бұрын
88
@mcfwelding
@mcfwelding Жыл бұрын
87?
Repairing a Rusty Frame on a GMT800 Truck [Cheap Duramax Part 2]
22:47
ЭТО НАСТОЯЩАЯ МАГИЯ😬😬😬
00:19
Chapitosiki
Рет қаралды 3,4 МЛН
How Strong is Tin Foil? 💪
00:26
Preston
Рет қаралды 150 МЛН
Win This Dodgeball Game or DIE…
00:36
Alan Chikin Chow
Рет қаралды 42 МЛН
How to repair rust..! So reparieren Sie Rost
22:07
Hamid Suri
Рет қаралды 608 М.
Woops!! Excavator had a bad day!!
30:04
I C Weld
Рет қаралды 1,8 МЛН
Welding Repair - Patching Holes in Dump Truck Box - GMC C8500
32:27
Captain Kleeman
Рет қаралды 59 М.
Already breaking the brand new shear!
22:28
On Fire Welding
Рет қаралды 796 М.
Risky Rust Repair!  (Emergency Welding Job)
14:01
Meltin Metal Anthony
Рет қаралды 83 М.
WORST FRAME STRETCH DOUBLE FRAME EVER DONE! PUT THE TOOLS DOWN AND WALK AWAY!
17:51
Fixing Scary Farmer Fixes - Hayrack Tongue Repair
18:21
Watch Wes Work
Рет қаралды 449 М.
WILL IT START ? - THWAITES DUMPER
23:40
Lord Muck
Рет қаралды 39 М.