Worked!

Thank you for posting a ceiling fan install video. 🫡

Thanks for the excellent video. I have a weird situation and thought I'd see if you or others have experienced the same. I have the same unit as in your video. The jumper wire info is great and helped to isolate my problem to the sensor control. I've replaced the sensors 5 or 6 times over the last few months. They will usually last one to three months and either quit making ice or won't stop making ice. At first I thought maybe the manufacturer had a bad run of components but after this many replacements I'm not sure what's going on. I've purchased them on Amazon and then switched to an online parts supplier. They all look the same anyway. It is so strange that some of the sensors quit making ice and some won't stop??!! On the sensors that quit making ice I can see a burnt resistor on the main circuit board. On the sensors that won't stop making ice all of the components appear okay. The other fridge components all check out as working as best as I can determine. Now I just use a jumper wire until the ice bucket is full and then remove the wire until the bucket needs refilling. Thanks again for the concise, informative video.

Nice job. I have a 2012 Ford Edge with a plastic body. I am going to try and talk my son into doing the repair with me. Thanks.

looks so good!

DIDN'T LAST !!! EVERY RESTORE KIT VIDEO , is SUPPOSED TO BE the BEST !!! NO FURTHER AHEAD, than 5 YEARS AGO

Hi, great video. Hope yoy can answer this -- I replaced the light bulb for the headlamp. It worked for awhile then it did not work. Took it to my friend who's a part time mechanic. He said he just tightened the bulb in the socket. Again it worked and then stopped working. So i'm thinking it is the socket/wiring bit?? which I dont know what to call properly . Or loose wiring somewhere? Do you have any suggestions? TIA

You da man Stan 👏

My electric 1998 Yamaha golfcart died when running..help pls..Tks

Thank you that’s good one God bless you brother great information

Clinton, i want to replace the headlight covers from the headlights any advice is helpful, your video is the best on this subject,

Shouldn't you at least cover the alternator? It wouldn't be good if some of that water splashes on to the alternator while the engine is idling.

9 years later and your video is still the best. I followed the instructions and had no issues whatsoever. Thanks!!!!!!!!

Thank you Clint! This was a great reference tutorial. I have a comment and an update. -The comment by @chubam... was useful - thank you. -I have a 2008 RX400H and the bulb is not the "L" configuration that you show. It's a "HID Xenon D2S" and it is held by retaining clips once the connector is removed (inside the cover). Note that I have a couple of reference photos but don't have a way to attach them.

Awesome video! I have to do it to my daughter's car to fix the front and rear bumpers

Excellent review, and really appreciate the one year later update!

Thank you. I was hesitant on replacing till I watched this

Good video!

Amazon new headlights for $100; no sanding required! You’re welcome and your mileage may vary!🙏🙏🙏

Might be the most bestest vid about the subject. I relate.

Incredible video. I feel sorry for people who don't seek out videos like these.

How do I test the cylinoid if good without replacing?

Thank you!!!

Wooow... thank you soooo much!! Answered all the questions I had. Time to tool up and get er done! 💪

Engine won’t run. I can touch positive and negative and engine will run. Is it the selinoild?

I’m trying to do this to the other side which isn’t as easy I have to take everything apart and was looking for a video to help but no one want to do a video on that

Hey clint I don't know if you still reapond to messages. I have a 1997 lexus es300 with the stock Pioneer amp and subwoofer. I blew my subwoofer out and I bought the replacement you linked but I'm worried that the starting RMS is going to fry my stock amp. I bought the 8 inch kicker 4ohms 200w rms, 400w peak.

Do you think it would be beneficial if you were to do this on a yearly basis so that would not be so much to remove and improve in the surface?

That does look very nice

There is now a Turtlewax "2 in one headlight cleaner and sealer" product that might help keep the fogging from coming back if used a few times (like every time after a carwash) a year not a heavy duty "restoration" but might help maintain ?

Nice job. Definitely gives people believe the confidence they can do this themselves.

Just used the Sylvania kit after watching project farm. Literally brand new. Incredible product!!! I loved the 1 year update. I think you can use the highest grit sandpaper and reapply the uv. Probably take 5 minutes.

Excellent video. I had to remove my RS rear door on a similar, 2010 Lexus ES350. I read in another video that these doors weigh "270 lbs". Such nonsense. FYI -- I weighed the RS rear door. The panel weighs 8.5 lbs and the door weighs 56 lbs. for a total of 64.5 lbs. All 4 doors ES350 don't weigh 270 lbs.Important note: If you're removing any door, unplug battery for 60 mins. before detaching wire bundle at door hinge. There are 10 air bags in a 2010 ES350. Detach battery to avoid possibly setting off airbag in door.

Please DONT TORQ WORN HARDWARE !!!!!!

U say u used a drmmer

This was perfect for my situation. Thanks so much and the link to the parts was perfect. I had to replace my ice maker after 6 years and now after 11 years I thought I was going to have to replace it again. But thanks to your video I realized that it was my sensor and not the ice maker. Saved me lots!!

Thank you! Great video

I looked on your website you guys don’t make 1 for the Lexus LS430???

Can you put the Dakota before you put dodge to keep others from wasting time on clicking when it can be another type of dodge

You did very well and have given me the confidence I need for very similar scuff mark! Thanks

Great video!! 🙌🫡

Great video. Wax your headlights once a year and you will slow down the oxidation process significantly after restoration. You can also wax your headlights new from the factory once a year to greatly slow down the oxidation process. Best, JB

Bummer. First of all, thank you for the very informative video. I found one day that I had the blinking lights of doom, found your video and when I used the jumper it immediately went into harvest mode and continued making ice. Unfortunately I have tried 3 different sets of boards now and they all fail. The 3rd one I tried seemed to be fine, but alas when I checked in the morning nothing had actually happened and it was back to blinking. I have 120v on the emitter and receiver so I'm baffled as to what is going on. Any thoughts? Thanks again!

If the new solenoid connection posts don't match up with the old one, how do you know which is which? Thanks.

Works exactly like you said. I used it today on my Kia Soul. Don’t even need anything to scrape with. Just use paper towels and a soft towel. Thanks for your video👍

What’s the exact part that’ll fit? I have 2000 es300 & having trouble finding the right o2 sensor.

Thank you- looks like my Lexus has aftermarket suspension parts so no other videos were helpful. This one is great

11/13/24 , reverse mode there is a click, forward mode no click, does not move F or R, cart is a 2018 club tempo thank you for the video.

Thank you for a nice clear demonstration

That's a master piece 💪