thank you very much to make the video and benefit all the world, I fixed my trendmill by this video
@FitnessEquipmentHelp2 күн бұрын
You are welcome!
@noraemilie3 күн бұрын
Amazing tutorial! I had trouble with the paper instructions, but this video made the instructions clearer
@woodstream61375 күн бұрын
Great tips. Hard to QC if evenly lubed considering the lube is on inside of belt.
@FitnessEquipmentHelp4 күн бұрын
It can be difficult, particularly on models where the belt sits under the deck rails. If the deck stores in the space saver position It may be easier to check the lubrication on the underside of the belt.
@tort47557 күн бұрын
We have an S22i Studio Cycle, just out of warranty. There is no resistance and the incline is acting up. Got a new controller, but no difference. Got a new console/monitor, but no difference. The console works fine, but when starting a program, and using the pedals, there's no resistance, no rpm showing, no adjustment of incline. Tried the pin restart as well. Can you please help? I would hate to trash a 3 year old machine costing $2,100 - plus spare parts and failed repairs....
@FitnessEquipmentHelp5 күн бұрын
It seems like there is no communication between the console and the control board. Communication signals between the two boards takes place along the blue and green wires in the main wire harness any damage or loose/disconnected green or blue wires any where between the controller and the console will cause this issue. I would check the wires for wires pulled out of connectors or fastener damage or wires that have rubbed on something and worn through. If the wires are intact then I would ask for a replacement circuit board. Its not common considering the number of these types of bikes out there but I have seen bad boards before.
@bennieanderson74497 күн бұрын
This was a very useful tutorial. The only thing I needed to see how to start it.
@FitnessEquipmentHelp5 күн бұрын
most ellipticals, including this one, should start a workout when you begin pedaling. Some may require you to press a start button on the screen.
@Mangoomads8 күн бұрын
Is this the same for the rw600?? Because I had to move it so far from the magnet so it would track the meters right but it’s still off
@FitnessEquipmentHelp5 күн бұрын
Yes this same adjustment applies to every product with a reed speed sensor switch. Usually moving it closer to the magnet improves accuracy.
@astrokitten368613 күн бұрын
Mine is stuck about 1 foot off the ground. All i did was lift it up to vacuum under it, and now it won't go back down. Any ideas?
@FitnessEquipmentHelp10 күн бұрын
When I have seen this it is because of a bent storage latch tube. Disconnect the latch at one end and carefully lay it and the deck on the ground. if it seems to work correctly I would replace the latch tube.
@timstevens282816 күн бұрын
I just replaced the controller board and immediately after plugging the unit in (correctly) the bike calibrated. However the screen is still black and the incline and resistance do not work. When I unplug the speaker on the screen it makes a sound indicating there is power to the screen. Any ideas?
@FitnessEquipmentHelp10 күн бұрын
If the controller is new (and presumably outputting 12VDC to the console). Then that would indicate a failure in the console. If you have a way to check DC power to the console you should have 12VDC measured between the red and black wires in the harness when the console is plugged in. If it drops to 6 VDC when the console is plugged in then the control board is bad and I would ask for a replacement if your retailer offered any kind of guarantee.
@timstevens282816 күн бұрын
I just replaced the controller board and immediately after plugging the unit in (correctly) the bike calibrated. However the screen is still black and the incline and resistance do not work. When I unplug the speaker on the screen it makes a sound indicating there is power to the screen. Any ideas?
@taycannon940326 күн бұрын
Video great but equipment is fragile nothing aligns the same in the video
@FitnessEquipmentHelp25 күн бұрын
If you are having problems with alignment make sure you are leaving parts loose and not tightening any of the fasteners until you are instructed to do so in the assembly instructions. Good Luck.
@cledr248522 күн бұрын
the handrail is inches off. 2-3 inches too narrow to fit onto uprights.
@FitnessEquipmentHelp20 күн бұрын
@@cledr2485 This is usually because the uprights are too tight. You will need to go back and loosen the upright bolts and only tighten them when instructed to do so in the assembly instructions.
@judyamaya2099Ай бұрын
Hello question if my pedals are so hard when I pedal what could it be is it something I pressed in the monitor or just something wrong with the bicycle
@FitnessEquipmentHelpАй бұрын
All the buttons on the console do is tell a motor to move a magnet closer or further away from the flywheel. If you haven't pressed the resistance increase button or the console says you are in a low resistance level then it is unlikely related to the console. I would look at the resistance mechanism in the machine itself.
@billhill7275Ай бұрын
Thanks for this. The problem with mine is that the roller circle comes off -that fits around the assembly and which directly contacts and rolls along the track. Does that require glue or do I have to replace the whole assembly with the roller piece?
@FitnessEquipmentHelpАй бұрын
Check out the Exploded drawing for your particular model. (It's found in the back of the users manual.) It should show you what serviceable components are available for your specific model. You can download a copy of your manual from www.iconservice.com if you no longer have the one that came with your equipment.
@louisflores4060Ай бұрын
Do you have a video on how to replace the band return spring?
@FitnessEquipmentHelpАй бұрын
I don't but once the side shields are off its pretty intuitive. the problems people case are that the part (and the instructions) indicate that the spring housing should be rotated counter clockwise. It is actually the axle that should be rotated counter clockwise. When I have replaced them I have turned the spring housing clockwise (against the arrows printed on the part). It is the way that seems intuitive. If you do it they way that feels right and don't overthink it you will be good to go.
@szpxd1364Ай бұрын
I'm having trouble adding a credit card as a payment method I keep getting the message 'Cannot add payment method'
@szpxd1364Ай бұрын
I'm having trouble adding a credit card as a payment method I keep getting the message 'Cannot add payment method'
@iTzErnestАй бұрын
Where to buy that key?
@FitnessEquipmentHelpАй бұрын
Parts are available at www.iconservice.com in the USA or from your local distributor in other countries.
@brandynsmith8375Ай бұрын
My x32i looks complete different. Do you have another video for the newer models? It’s not all one board.
@FitnessEquipmentHelpАй бұрын
I'm sorry, I do not but the process is essentially the same. The controller is still on the top side of the electronics bracket it just now has fewer wire connections.
@JeffWilkinsMVPАй бұрын
My Carbon TL doesn’t have a left side adjustment bolt. The track is slipping like crazy.
@FitnessEquipmentHelpАй бұрын
Tensioning the belt to prevent slipping caused by a loose belt can be done using the idler roller bolts in the rear of that treadmill. Also note that on some models the drive belt may also be to loose causing slipping. So you may need to tighten the motor belt if tightening the walking belt does not improve slipping.
@Unique77783Ай бұрын
I cannot find how to remove the drive belt anywhere online for a superfit treadmill. Mine do not come off like that
@FitnessEquipmentHelpАй бұрын
I'm sorry I don't have any information on that brand. I would recommend contacting the manufacturer.
@pedwards69722 ай бұрын
my resistance is on even when the bike is "off" could it be stuck from not using it in while? in the video do you leave the m6 shoulder screw on the resistance arm loose? TY!!
@FitnessEquipmentHelp2 ай бұрын
"Loose" is relative. You do not want it so tight that it crushes or binds the arm so it can not move.
@jaqelang232 ай бұрын
How do you turn the back screws with the wrench in step 20? I cannot figure out an angle that will get to them, and the video only shows the tightening of the 3 front screws on the left and right.
@FitnessEquipmentHelp2 ай бұрын
I think the easiest way is to use a socket wrench with a short extension.
@micoderup23 күн бұрын
@@FitnessEquipmentHelp Thanks in advance for that help. I am about to assemble one.
@leungfy12 ай бұрын
Hi, my Schwinn 130 is making some clicking noise every time I pedal. Upon inspection, I noticed that there is some play in the pully shaft assembly (bottom bracket). I think the bearings might be wearing out. Nautilus equipment (who makes these bikes) only sells the entire crank assembly. But I can likely fix this by only replacing the bearings. I managed to find some exercise bike bearings online which looks similar (12 metal balls type) to the those in the picture in the manual. Do you know bearings are universal in exercise bikes?
@FitnessEquipmentHelp2 ай бұрын
I do not know for sure if the bearings are universal but they have been the same in many of the bikes in have seen.
@leungfy12 ай бұрын
@@FitnessEquipmentHelp thank you
@GlampingWithGuero2 ай бұрын
Just finished installing mine took me about 30min total not difficult at all however, you do not need to completely remove the right panel, you’re just create more work for yourself you’ll see what I mean when you start doing it. Also the symptoms of my bike were incline, decline or resistance wasn’t working.
@eltonlumban-gaol97812 ай бұрын
How often do you do this if you use your treadmill a couple times a week?
@FitnessEquipmentHelp2 ай бұрын
It really is on an as needed basis. the underside of the belt/deck should feel oily but should not be wet and dripping with lubrication. the manufacturer lube is a high performance lube and does not need to be frequently applied but you should check often when you do your regular maintenance. some people apply it annually, need it or not. you are more likely to need to reapply lubrication if you keep your treadmill in a hot, dry or dust/dirty environment or if you go for long periods w/out use.
@Fernmdc2 ай бұрын
Great video, thanks!
@FWS80722 ай бұрын
Like many comments my S10i (NTEVEX14718.1) has stopped working. No resistance or incline and nothing happens when I calibrate the machine. Although when I first tried it did seem to do something after a long time and now appears to be stuck on a slight incline. Since then I have tried multiple calibrations and no movement at all. The machine still turns on and I can go into a workout and the console shows the resistance and incline levels changing but no watts or distance so the workout cannot be saved. I did as the video above explained and all the wiring seems fine. Any idea as to what may be the issue? Thanks in advance.
@FitnessEquipmentHelp2 ай бұрын
If the wires are intact and the console software is up to date then I think the most likely issue is a corruption in the controller. All of the motors and sensors go to this board before the information is communicated to the console. It is 1 part that explains failures in the speed sensor and the resistance and the incline. It's not likely you have 3 failures.
@FWS80722 ай бұрын
@@FitnessEquipmentHelp Something I have noticed when I checked the wires on the controller is that there appears to be a fair bit of white glue by the looks of things around the 3 red wires and going between them. Really not sure it is supposed to be like this looking as your other video on the controller replacement doesn't look the same. I have taken a photo of it so not sure if I can send this to you to have a look at?
@FWS80722 ай бұрын
@@FitnessEquipmentHelp Thanks for the reply. Looking at the Icon website for my model (NTEVEX14718.1) am I correct in saying you think I need part number 402796?
@FitnessEquipmentHelp2 ай бұрын
@@FWS8072 some of the manufacturing facilities may have used hot melt glue to secure the wires. This will very by model and factory. It may require you to peal off the glue before replacing parts but it should not cause any issues with the bikes functionality.
@FWS80722 ай бұрын
@@FitnessEquipmentHelp Am I correct in saying that you think I need part number 402796 for my model?
@marcleblanc56392 ай бұрын
Thank you great vid 😊
@marcleblanc56392 ай бұрын
Its helping realize mine bike belongs in garbage 😢god dam f$&@ rings. But good vid still. I have no patience anymore
@jamesbauer80622 ай бұрын
This video is just want I was looking for, just had troubles finding it.
@hugocontreras40672 ай бұрын
Hello, I am not sure if the problem is the motor or the control panel. The incline/decline stoped moving , as soon as I put it a part and tested the motor without been attached to the bike, it does work, but when I attached, does not move , it just make a noise , a couple clicks , then nothing. I tried to calibrate it to, it does do it when the bike is not attached only. 😔 Any suggestions 🙏🏻
@FitnessEquipmentHelp2 ай бұрын
If the motor extends and retracts when not connected to the machine. then it sems like there may be something physically keeping the unit from being able to move up and down.
@hugocontreras40672 ай бұрын
@@FitnessEquipmentHelp that was my first thought, I loosed all bolts a little bit, put some grease everywhere, and nothing happened 😞. Maybe something got screwed up on the board 🤔. I got this bike used and they told me that the resistances don’t work, checked the connections and saw that the resistance connector was put inverted, (colors of the cables), so I flipped and resistant stated working 😊. I noticed that the resistant moves too with the inclination , so maybe got crazy on the board for having those cables connected the wrong way ?
@FitnessEquipmentHelp2 ай бұрын
@@hugocontreras4067 Depending on the unit the wires to the resistance motor may be in a harness that reverses the yellow and blue wires and the red and black wires. This is done so they can use the Same motor in different applications. In any case this should not have any effect on the incline unless the resistance bracket is interfering with the frame when it tries to decline. I don't think it could cause a failure in the board. I think it is possible that the motor may have failed. Seems the board is working if the motor runs when not attached.
@Jeremiahlation2 ай бұрын
I found my knock. It's the main crank itself has a tiny bit of play. I'm not sure how to fix that.
@FitnessEquipmentHelp2 ай бұрын
Side to side movement on the crank may be taken up with a small spacer (very thin washer). If the crank spacers in the elliptical have worn thinner you also may just need to replace those spacers.
@AdrianaCapistran2 ай бұрын
Can you guys show how to replace the computer of elite 900 NTL89121 please. Thank you
@acuda273 ай бұрын
Did not work
@spncrw3 ай бұрын
How do I know if my controller board is dead or the console (or something else)? My screen is completely black though I do hear the fans whirring in the console. The bike does raise up/down when plugging in (though this doesn't happen all the time). Really hoping it's a controller board issue and not the console as that's so much more expensive.
@FitnessEquipmentHelp3 ай бұрын
To know for sure you can measure the output voltage from the controller to the console on the red and corresponding black wire in the upright harness. with the console plugged in you should have about 12VDC to the console on this wire. Some failed controllers will only deliver 6VDC when the console is connected. This may be enough voltage to get the console dans and brain board to operate. (The incline is controlled by the brain board.) The tablet however needs 12VDC to come on. It sounds like the controller isn't delivering enough power to the tablet display but you would need to measure it to know for sure. It's possible it is a fault in the tablet, but I think that is less likely.
@theIRISHboss3 ай бұрын
If this doesn't work what then
@FitnessEquipmentHelp3 ай бұрын
If there is a failure in the buttons and it cannot be resolved with verifying the connections or freeing stuck buttons, then it is likely the part will need to be replaced.
@yulisanchez92153 ай бұрын
How to used ? I used have old one where I can see track this one I can’t . It help me how many laps I was doing
@FitnessEquipmentHelp3 ай бұрын
Although this model does not have a track display it will give you your total distance in miles or kilometers on the screen. A typical track is 400 meters. 4 times around the track is aprox 1 mile. I hope that helps.
@IR-RA3 ай бұрын
My treadmill makes motor kind of noises, they are not loud but it was not like that in the beginning, how do I fix it?
@FitnessEquipmentHelp3 ай бұрын
The sounds the treadmill will make will change with use/wear and tear, some of which is unavoidable. The best way to keep the treadmill quiet is regular maintenance, This including lubricating the walking belt and keeping it properly adjusted. This keeps less strain on the motor allowing it to run more quietly. Keeping all the other parts tight will prevent nocking noises and replacing worn out parts like the, walking belt, will keep the motor running efficiently.
@cultureofhiphop3 ай бұрын
This video is a lifesaver, that squeeky noise was driving me crazy! Thanks for making this video!
@RandoBagginz3 ай бұрын
How easily is the 2450 to disassemble? I’m purchasing one for the house I’m in currently, but plan on moving in a year or two.
@FitnessEquipmentHelp3 ай бұрын
Its not too bad. If you can move large pieces and are not intimidated by wiring under the hood then you can disconnect the upright wire from the lower board and and out of the belly pan. Then you can move the uprights and console as one assembly and the base and deck as a second part. You can also just reverse the assembly instructions. There is always the possibility of damaging the plastic covers and the plastic grommets that hold the wire harness in place can be difficult to extricate from the uprights. (they're not easy to remove from the outside and there is no access on the inside of the upright). Damaged parts are usually easily replaceable.
@gvega19783 ай бұрын
just bought one today, mine didn't come with the ground wire off the leg, only the one off the board. What i do in that case?
@FitnessEquipmentHelp3 ай бұрын
If you are missing parts then you can contact member care or the warranty holder in the area in which you live.
@prple60313 ай бұрын
My crossbar does not reach each of the sides
@FitnessEquipmentHelp3 ай бұрын
Loosen the bots at the bottom of the upright. They should be very loose during assembly. Then tighten them when instructed in the assembly instructions.
@waydav1s3 ай бұрын
I would think that the resistance is "calibrated". Change it manually and you will screw up the calorie counter. In order for accurate calories to be known, you MUST know what the resistance is by measurement via either a know calibrated reference point OR real-time via a strain gauge. This will ALWAYS be a issue the older the machine gets because the magnets lose their strength over time. I am dealing with this exact issue on a bike my wife has. I need a way to know how much measurable force is being used at a given resistance and read the calorie count the machine gives. Then adjust the resistance to match the calorie count using formulas to convert force to calories. The trick is: WHAT do you use to measure the force? A motor, Strain gauge, A digital scale with peak hold connected to a pedal and rotated? Hmmm....
@FitnessEquipmentHelp3 ай бұрын
Thank you, this is correct. At the beginning of the video it does indicate that this method can be used to calibrate the resistance too a watts meter or other device also. There are many instances of users however that are just wanting to make adjustments for a variety of reasons, and rather than paying for a technician this video shows how those adjustments can be made by the user.
@supercoolsteel3 ай бұрын
My display won't light up at all It just keeps beeping no matter what I press
@FitnessEquipmentHelp3 ай бұрын
this sounds like the magnetic safety key is not on the console or the key switch in the console is faulty.
@duke83893 ай бұрын
This video is horrible! The title is totally misleading and only says to watch another video to replace resistance motor to deal with the resistance motor problem!
@bobbysmitty87833 ай бұрын
Why won’t the bolts on the fans come off when using a socket wrench?
@FitnessEquipmentHelp3 ай бұрын
The bolts are on a spinning axle you may need to hold the fans and therefore the axle from spinning before they will come loose.
@bobbysmitty87833 ай бұрын
no matter what I do the axle spins
@HeelMario3 ай бұрын
What kind of oil can I use for my Nordictrack treadmill?
@FitnessEquipmentHelp3 ай бұрын
The manufacturer recommends Icon/iFIT performant lube. it is the only lubricant tested for these products. it should be available at www.iconservice.com or your local distributor of NordicTrack products if outside of the US.
@breanne43493 ай бұрын
'PromoSM' ✋
@bobbysmitty87833 ай бұрын
what if my side shields don’t slide off after removing the screws?
@FitnessEquipmentHelp3 ай бұрын
I would look for additional screws. The two sides connect together and connect to the frame. Some of the screws that hold the 2 pieces together are only on one side which makes keeping track of where they are a little tricky.
@mindlab780ab63 ай бұрын
What if it’s missing a crossbar from the packaging! How do I get another one from the manufacturers?
@FitnessEquipmentHelp3 ай бұрын
Contact member care by reaching out to the number in your manual or my.ifit.com if you are in the US. If you are outside the US. contact your local member care office or your authorized distributor (where you purchased it). A replacement part can usually be sent out pretty easily.
@mindlab780ab63 ай бұрын
@@FitnessEquipmentHelp thank you so much
@llopez32014 ай бұрын
Since ive had my s22i, ive had to do this numerous times. No longer working and now stuck on "erasing", the updates are killing these consoles yet we are forced to fit the bill to replace.
@FitnessEquipmentHelp3 ай бұрын
The best way to keep the console working is to perform regular updates as they become available. You may have to do several updates once you do a pinhole reset to get caught back up. If you are covered under warranty or a service plan the cost of parts should be covered if you have a manufacturer defect.