I have an easy solution to ice dams. Turn your thermostat down! Put on a couple of sweaters it works every time.

On the vehicle battery disconnect, im pretty sure it should be on the negative cable.

clearn your van dirtbag

This charge fast mines is talking long

Hello, my brother, I have a problem with a 2005 Jeep Cherokee. When it goes at 60, emergency mode appears, the gear sticks at 3, it says check engine, and when the engine is turned off, it returns to D. What is the solution and what is the problem?

Nothing worse than watching a guy work with one hand. Spend the $5 and get tripod or something

I would like to find a way to locate stolem bottles even though I told the local gas supplier they were stolen they still want to charge rent or me pay for them, I thought they should have insurance for such occurances.But this is my first time down this road having something leased that gets stolen

you mentioned picking up bottles out of the dump and trading 2 smaller ones for 1 bigger one at the welding supply if I understood, then who owns the 1 large bottle? it still belongs to welding gas supply co and you have to lease it??

I love these old timey productions. Periscope Films any day of the week.

Thank you so much! The tire was changed. They didn't put the spare back after fixing it. 👍🏽

I have to believe that some effort to clean up dirt & grime especially around the shower drain would have been helpful.

A very good video, I just got my NLP14 this week and will be cutting out the back of the battery box next. An FYI for your watchers, order the battery Noco factory direct. It is the best way to get the 5 year warranty honored should you need to. With their promo code it was also cheaper than most anywhere else.

Life saver! Thanks !

Those noco batts are not lithium ion. They are lithium iron phosphate (LiFePo⁴). Be aware of the difference

THANK YOU SO MUCH

No spare tire in the Wk1 Jeep SRT8

277k miles?

Just attempted mine. Number 6 sheared off. Number 2 is so tight I don’t want to risk it. I’ve decided to leave them in there and run with four working.

I must have watched this pair of videos about 10 times over the years as I planed to do this job to our '96 Roadtrek. I finally got around to doing it this spring. This video helped a lot, so thanks. The service manual pages were useful since I only have the manual for the pickup and the suspension is different. It was also good encouragement and let me see all of the parts of the job before I got into it. It was a bit harder on our van because we have the 4 ton axle and the parts are hard to find. I had to press the bushings and joints out of our old control arms. The upper control arms with the thread in joints are a real pain. I wasn't able to get them to budge with a wrench and ended up pushing them out with a press and then screwed in new ball joints. Even though this is a big job, it's not that bad. If I were to do it again it would go much more smoothly 🙂

Thanks for the video. I just used a pronghorn to hold my battery in the modified box. Plenty strong!

Been around this stuff quite a long time and you are far better to lease bottles, they take care of re-certing them and all maintainence and you are never without a bottle to use as long as you pay the lease.

I'm in the process of removing my turbo to get to the oil cooler in the valley. Have you gone that far? I'm just looking for more help to make it less pain full. Its buried in there pretty good.

Shit. It is hard to use. Have to stop and change every time

So you gotta use the old gasket mine was leaking so bought that gasket made the dang thing leak on opposite side lol bought another gasket figured I was putting in wrong thanks helpful

Could you have used a crowfoot??

Your talking abunch of bullshit man we aint worried about done of that bs in arkansas

Hitting the pin multiple times just mushrooms the bottom of the pin, making it harder to remove even when the knurled part of the pin is clear. When using the tool, tighten the bolt very hard against the pin, then hit the bolt upwards with a hammer (one hit only), then tighten the tool again, repeat. The bolt applies a huge force on the pin, and a further tap with a hammer shocks it.

AC Fan Rumble is caused by leaves in the Blower Housing. It's an easy removal under the Glove Box to clean out 😎

Hello so i am charging my battery more hours then it says on the manual but 25% , 50% , 75% LEDs are still solid and the 100% green light is pulsing on and off even thou it should be solid long time ago .

Can't see how the o rings are installed, due to poor lighting.

You put the title as removing the generator bu in reality you reality you shifted the generator.

never ever jack up on dirt. even with jack stands. if any of the jacks dig into the dirt over time and the vehicke becomes uneven, bad things can happen

please fix your seized pressure regulator and battery monitor connections. What about the water system? Otherwise knowledgeable video

Thanks man. This helped me with my 08 civic

Geez the wrong gasket

Thank you very much, Mister Rivett! ❤

I swap on purchase as a rule to get current hydro dates. Many LWS are casual about the little cylinders so long as they've no arc marks etc. Blank neck rings are common to milsurp cylinders which of course you can exchange when they need hydro but those tend to disappear on the east coast so you may end up with a marked cylinder in return. NONE of the welding supply rules are actual laws and merely reflect over a century of industry consolidation. Another note is you'll still see ancient Linde cylinders marked with swastikas and that is NOT at all related to the Third Reich but was a mark used before WWII because it was a good luck symbol for thousands of years. They are NOT WWII surplus either. Many are stamped with a square to alter the mark. CO2 cylinders besides being useful for MIG welding are great for seating tire beads (get the correct regulator!) and the usual off-road "power tank" uses.

April 2024 I’ve just followed your video to the word and done the exact same upgrade with my Stagepas 400bt. Which means I can gig with it this weekend and I don’t need to haul the big rig out in the car!!! Thank you so much 👍👍👍

I see your video, I'm thinking about this kit or 3580 in master kit, I can't decide, I like this one better, but it doesn't have a great extension, what do you think?

When all else fails read the instructions! Lol

Call LiftMaster tech support. They will send new logic boards for free if you have issues.

1. Wrong gasket 2. Change the o ring on the fitting, protruding the back of the cooler block. Its plastic, and they leak. Now, a pro tip, if you're tracking down a pesky oil leak that is around the starter area. Pull your crank sensor above the starter and replace the O ring.

Follow the 10 commandments and repent from your sins. Jesus loves you!💙

Diesel jeeps have the W5j400? Thats a different level than the W5a580

What the fuck did you diagnose? He didn’t do anything but a bunch of bullshit talking find something else in life to besides make stupid videos.

Hi Stephen. I just found this video while thinking about building something similar. Question: have you had the chance to use the Stiles Herman roller? If so, do you have a video of the tool in action?

What type of sand do you use?

All gasket will seal with what you have......... just time to harden. And you climate is to cold for the product to work. Weeks your climate. Australia hot 40c i still wait a week. 100 percent over done. Will not brack of in your filter. The more time you have and patience is better. God bless mick Australia

BOC stands for British Oxygen Co

Watching folks do that crap on the ground makes me glad i have a 2 post car lift.