Thanks. The top bolt still gave me hell.... But what a blessing having you show me the way. Right on.

My window is going up slow then stops... i think I could get away with just doing the motor only. Why spend money on other part

Thanks for your video it helped me with shifting. But the key is stuck in what is this piece called.

When i start compressor air with oil how fix it please tell me

quick question, from what I see one red wire is connected to the alternator 2nd red wire is connected to the coil harness, where are the other 2 black wires connected too? and if the ground, do I just connect it to the ground 102 bolt?

🎉🎉🎉🎉

I have a 2015 Chevrolet Traverse and the frame on mine broke at the top. This video is the only one I have found that shows the disconnect tabs for the old plastic frame. The most difficult part is the front. For the driver seat front plastic frame there is a metal push connect tab that once that is unlatched from the front plastic frame allows the driver seat front plastic panel left lower side to partially come off/move forward towards the front of the car. This allows enough gap to allow the old side panel to slide off/forward from the flat plastic post that is on the front panel frame. Looking at the new side panel like he said it would look like a screw that would hold the front side panel to the front frame. That is not the case as the flat plastic post on the front panel frame slides into the slot on the new side panel front. At the same time the two plastic latch clips on the new side panel slide effectively side ways (moving towards the right side of the car or towards the passenger side) into two slots upper and lower on the front panel. Torx bit #30 is correct size for removing the seat belt latch case screw in order to take apart the seat belt upper and lower to get it through the new side panel. I order a new side panel from Ebay (item number 114518080091) for $24.24 shipped: www.ebay.com/itm/114518080091 A good idea while doing this job is to go ahead and replace the electric seat switch too while you have it all apart. Seat switch also from Ebay for $18.03 shipped: www.ebay.com/itm/125297634560

We always used paper to hold the bolt in the socket.

How did it work after you polished the plastic tab?

Removing the shift linkage is hard to do but you just glossed over it

I’ll be trying this

Thank you !! I’m dealing with my buddies 2016 Canyon. Replaced the converter seal but it is still leaking . I removed the trans again and bought a new converter but I want to make sure the old one is leaking .

Tin foil works well to hold bolts in sockets too.

It works!

Just saved me a ton of money with this video!!! Thank you for posting!

Cuantas pulgas se habrá comido este patito y el perro como diciendo sacame todas que no quede ni una.

Thanks for uploading. I think this is the only video on this for the traverse that I've found. This is something I have to do on my driverside. This is a good video to get me in the right direction. Thank you!

Fixed my truck thanks

Video difficulty 2 real life difficulty 100000 😅

Ahhhh the struggles I went through to get it off 😂 after an hour I finally got it popped off.

Disconnect the trim...but how? If you don't do it right plastic will break. (bad engineering) There are may ways to remove plastic trim and every trim piece is different.

You forgot to show how damn difficult it is to take the old plastic off is. Great job

thank you. you are the very first person i have ever seen to actually show us which chip needs to be removed!

lol, wish i would have watched this before i made mine. it took prob a half hr before i picked .11 great video. will help others that can't wait a cpl days. i ordered some but was in the middle of a job and needed mine. 7 bucks on amazon with head gasket. Thanks for a great video.

So what part do you change to fix this problem ?

Impressive. But then yiu have to put fender liner back on.

About the most useless video I haver seen!

Wow…that was impressive! After watching half a dozen videos on this procedure I thought it was going to be next to impossible, but you gave me some hope! Thanks

The hard part of this is the front connector of the side panel. To bad you skipped that part.

Thanks this video helped me get my truck running again

Thanks u da man got me back on the road

Good camera work !

<3

Thank you for your video. My Buick Enclave is broken on both front seats. The tape is really ugly and I’m ready to replace. Thanks again for the information.

Awesome sir. Thank you 😊

I wish you could show how you got the front part off

The funniest thing is, while rottys are quite heavy dogs, they can be surprisingly agile and sporty for how they look. Ive even had one jump around 5-5.6 ft before! Fascinating.

Negev desert, awesome video!

Would this work on a 2015 spark base model radio?

Would this work on a 2015 spark base model radio?

That’s awesome. Thank you.

So you didn't show how to the plugs you said you's a pic but there's a couple of them not as easy as it seems but thank you for your info

Neat trick going in through the license plate bumper hole. Of course if the button on the outside fails, you could use the fob or button on the overhead console to open the hatch. I just replaced the glass release button on mine. Thankfully I could pop the glass with the fob, not sure how else you cold do it without drilling / breaking the trim panel.

Is it me or does this piece brake every 5 years 🤔

His mind was on the ball not the fence...

He don t kill the duck, animals are better that humains ! Just his ball , bonne journée

I have a different compressor but same system. Watched tons of videos and only this one could really helped me out to solve the problem. ZANKS A LOT AMIGO!!!

Lol, so he can get over, but he can't come back with the ball 🤔

More of a jump than a climb !

This random buddy of his, a duck. Wonderful