My compressor regulator is at max. My inline regulator is at 100 psi. My paint gun set at 30 psi drops all the way down to around 25psi when compressor is off. While the other regulators are still reading high. Wtf
@UndergroundPaintKingСағат бұрын
Sounds like you may have a issue with your regulator at the gun
@brunocristan704711 сағат бұрын
Can you continue to spray normal afterwards? Dumb question and i think know answer but bout to tackle a whole car with same gun and setup. Been creeping al your videos 😂
@UndergroundPaintKing5 сағат бұрын
Not a dumb question at all but yes you’ll be able to spray normal after setting your spray gun up like this
@joecunic370813 сағат бұрын
Whats the best setting with this gun spraying single stage
@UndergroundPaintKing13 сағат бұрын
The best setting is going to be determined by the material you’re spraying, it’s best to do test panels before spraying your project to see what works best for the materials you’re using
@MrPontiacfever20 сағат бұрын
I finally put mine together and having problems setting my air pressure.It keeps dropping to 0 and goes to 20 it won't adjust to the number i want.Is the regulator on my gun defective or user errror.
@UndergroundPaintKing20 сағат бұрын
It could be your regulator
@pigeonsofusa4262Күн бұрын
good job, so before you spray are you clean car with degreaser or acetone?
@UndergroundPaintKingКүн бұрын
Thanks I appreciate you and I usually use grease and wax remover
@gabrielcortez3053Күн бұрын
Does it matter if the adapter is short or long ? I have a short one for my drizzle d1 gun
@UndergroundPaintKingКүн бұрын
I would test it and see how it works, I would think that it would work for it
@gabrielcortez3053Күн бұрын
@@UndergroundPaintKingmine is looks like Your gun with the threads still showing, on your black widow did your experience any issues or leaks ? If not I think I’m fine with the sc2 adapter
@gabrielcortez3053Күн бұрын
Currently have the s2c adapter just fyi
@UndergroundPaintKingКүн бұрын
@@gabrielcortez3053 I didn’t have any leaks but you can always test it with some paint thinner etc. to see if you have any leaks
@user-xj4jh8ho4xКүн бұрын
My first car was a 1985 Buick LeSabre and it had the gold keys. It was my mother’s car and when I got my driver’s license, dad got her a new Crown Victoria and she tossed me the keys and said “suppers in the oven, your daddy’s taking me to get my new car”
@UndergroundPaintKingКүн бұрын
That’s a 🔥 story 💯 these cars are a great car to have ❗️
@sgtrickards5683Күн бұрын
Saw that gun yesterday. The Black Widow. That black and red color combo always hits. That was one of the reasons I picked up the A610.
@UndergroundPaintKingКүн бұрын
Those are my colors, they definitely look good and are both great spray guns
@MrPontiacfeverКүн бұрын
Wat up big dawg my question is did you cut out the filter in the pps cup to spray primer and sealer.I think im ready to paint my first vehicle.
@UndergroundPaintKingКүн бұрын
I keep the filter in when spraying primer and sealer Mr. Pontiacfever
@MrPontiacfeverКүн бұрын
@@UndergroundPaintKing Preciate it Fam
@UndergroundPaintKingКүн бұрын
@@MrPontiacfever you’re welcome 💯💪🏾
@Flowingwater02 күн бұрын
Thank you for your dedication to us. And keeping it honest.
@UndergroundPaintKing2 күн бұрын
You’re welcome and I appreciate you 🙏🏽💯
@Clasicks_662 күн бұрын
Good shite bro
@UndergroundPaintKing2 күн бұрын
I appreciate you checking it out 🙏🏽💯
@charlestoncreighton30402 күн бұрын
Much love n respect brother We appreciate u 🖤💫
@charlestoncreighton30402 күн бұрын
I appreciate you 🤚🏿🙏🏿
@UndergroundPaintKing2 күн бұрын
@@charlestoncreighton3040 and I appreciate you 🙏🏽💯
@heightsgolan87422 күн бұрын
been using autobahn clear for years and it is just as glossy. for about half the price.
@UndergroundPaintKing2 күн бұрын
Glad to hear it’s working out for you!
@sgtrickards56832 күн бұрын
I told you about the trailer I have to paint if you remember. It's for a friend. The trailer has a 6X8 bed, but it's 14 feet from the back to the front. He also wants the wheels painted. Considering I have experience, what should I charge to paint it? I told him $400, but I would like to know what you would charge for the regular guy coming in looking for a Rustoleum job. I'm still using a spray gun, but I'm painting it outside on a tarp. He doesn't want to spend much money. He already paid for the paint.
@UndergroundPaintKing2 күн бұрын
I honestly don’t know what you should charge to do the trailer, I don’t know what you have to do as far as prep work but I think 4-$600 is a good price range
@sgtrickards56832 күн бұрын
I bought the Fortress 27gal 200PSI air compressor today from Harbor Freight. They even gave me a free air impact gun. $120 gun. SMH. They're stepping up. I think I'm set now. I think the A610 will run fine. Been watching your videos. Thanks for always hitting me up in the comments. You're bringing back the love I had for painting in my Air Force days. I'm gonna work on building myself a nice spray booth next. Thinking about flipping utility trailers to grab some extra cash. Work my way up. You do good work, bro.
@UndergroundPaintKing2 күн бұрын
I appreciate you SGT Rickards and you got a nice package deal 💯 let me know your thoughts on the A610 and I hope the channel continues to be helpful to you in anyway possible ❗️Welcome Back💪🏾
@user-un5my5bw4j2 күн бұрын
I have a 155 and a 715. They both are outstanding and i use the 715 more for clear than my Devilbiss DV1-C clear gun since the output is twice as much with as fine as atomization. The white derlin piece in the back of the nozzle is not a gasket its a bushing. The gasket was between the nozzle and gun body
@UndergroundPaintKing2 күн бұрын
Yeah I agree that they are very nice spray guns💯💪🏾
@DD-gd3fr2 күн бұрын
Good info thank you
@UndergroundPaintKing2 күн бұрын
You’re welcome, I’m glad the video was helpful 💯
@davelock31662 күн бұрын
Thanks, man!
@UndergroundPaintKing2 күн бұрын
You’re welcome Dave❗️
@georgespangler15172 күн бұрын
Question,, what pressure are you spraying base and clear at with it?
@UndergroundPaintKing2 күн бұрын
I normally spray base at 26-28psi and I spray clear at 30 psi
@georgespangler15172 күн бұрын
@@UndergroundPaintKing Thanks, about where I am looks like in vedio your getting less over spray,, have you tried the black widow HTE yet,, it's hard to beat for clear puts out a 12 in even fan and amazing results
@UndergroundPaintKing2 күн бұрын
@@georgespangler1517 yes I’ve tried it, I have the 1st and 2nd version of it
@georgespangler15172 күн бұрын
@@UndergroundPaintKing ok,, love my blue spectrum HTE for piece spraying base and clear but when I'm clearing a whole car I'm going for the widow HTE. You do good work my friend.
@UndergroundPaintKing2 күн бұрын
@@georgespangler1517 thanks I appreciate you 💯❗️
@georgespangler15172 күн бұрын
Great gun sprayed 30 cars with it and only one had to be buffed, but the black widow HTE can't be beat on clear, l use spectrum HTE for base and widow HTE for clear and putting out show quality
@UndergroundPaintKing2 күн бұрын
I agree that they are great spray guns that put out quality finishes!
@headsuptv68852 күн бұрын
Big gal 😂
@UndergroundPaintKing2 күн бұрын
😂
@erniesolis63633 күн бұрын
Very nice
@UndergroundPaintKing3 күн бұрын
Thanks, I appreciate you checking out the video!
@deankay44344 күн бұрын
Spraying at 75% overlap, 35PSI at inlet but air pressure drop thru gun puts it at 10-12PSI at the cap. This correct. As far as orange peel in the clear, that could be sanding prep (400g for solids, 600g for metallics, 800 for pearl two part base). Plus increase pressure like you said, slow down movement, correct temp on reducer, or flow coat (Double Clear). Spray inner clear, called inter-clear by some manufacturers, but 3 coats, let sit to shrink if time allows for 5-7 days. Then wet sand at 600g, clean & spray high solids or European Clear for 2 coats (Charge Extra) but if done right, no cut & buff! UV protection package raises to the top of clear, wet sanding removes it. This shortens the life of the paint job. (Tech Tip; Spray inter-coat clear for use under flames, scallops and other graphics) otherwise you may get a haze between clear coats. "SprayAway" does this over vinyl decals and pinstripes sealing then in. Great review of this spray gun. The R500 is sold by several companies as seen on Amazon, even $88 for gun and 4 tips, caps and needles. Thanks. ASE Master tech since 78.
@UndergroundPaintKing4 күн бұрын
I appreciate you leaving the great tips and advice 💯💪🏾
@johnjenson57384 күн бұрын
I was curious about the amount of time that it would take to continue with that hood would you consider sourcing another hood ?Thanks
@UndergroundPaintKing4 күн бұрын
The hood could be fixed but I honestly would look for a better hood instead of fixing this one
@williamdennis95764 күн бұрын
What cup set up are you using ? I had a painter at a body shop give me 3m pps cup and liners but I can’t seem to find an adapter to fit the do you have any suggestions thx
@UndergroundPaintKing4 күн бұрын
Here is a shorts video I did on the topic, hope it helps kzbin.infoPty3u1ky__U?si=SvDCTmzDTr6GPldZ
@williamdennis95763 күн бұрын
Thanks for the info I ordered and it worked out perfectly your videos have given me the confidence to be able to do some painting I’ve done my old Harley with a rattle can
@UndergroundPaintKing3 күн бұрын
@@williamdennis9576 glad I could help with the videos 🙏🏽💯
@phordguy5 күн бұрын
Top notch UPK - my favorite color for sure and great finish - Very classy
@UndergroundPaintKing5 күн бұрын
Appreciate you checking it out Phordguy 💯💪🏾
@user-yx4yd7ho8g5 күн бұрын
What size tip did you use
@UndergroundPaintKing5 күн бұрын
1.3 tip
@JimEarns5 күн бұрын
Thank you for getting this info out. No one else has explained it or has had any idea about part numbers. 3M site is ridiculous to navigate. Liked and subscribed 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
@UndergroundPaintKing5 күн бұрын
I’m glad I could help Jim and I appreciate you for subscribing to the channel 🙏🏽💯
@rogeliogamboa76446 күн бұрын
Sir, thank you for very important information - very helpful for a DIYer
@UndergroundPaintKing6 күн бұрын
You’re welcome and I’m glad the video was helpful 🙏🏽💯
@davidbryant58756 күн бұрын
You give me away to sand bondo and old paint down quicker been using a dewalt regular sander tired of going through so much sand paper on one panel. Thanks buddy!
@UndergroundPaintKing6 күн бұрын
You’re welcome and I’m glad I could help 💯💪🏾
@m.akbart38406 күн бұрын
I'm a beginner and I'm getting the porphis 155 that I watched you use in the other vid. Hey Underground King, will the porphis 155 work well with a 5 HP 20 gallon compressor?
@UndergroundPaintKing6 күн бұрын
It depends on what you’re doing, I think it’ll work well for doing small projects but attempting a overall paint job will be challenging
@m.akbart38406 күн бұрын
@@UndergroundPaintKing OK, I'm painting a car and I intend on doing it very well. I want a spray gun around 100-150.
@UndergroundPaintKing6 күн бұрын
@@m.akbart3840 The 155 is a great spray gun and I recommend you do panel by panel if you do the entire car
@sgtrickards56836 күн бұрын
I subbed, bro. You do good work.
@UndergroundPaintKing6 күн бұрын
I appreciate you subscribing to the channel 🙏🏽💯
@sgtrickards56836 күн бұрын
Have you ever used an inflatable booth? What do you think about them? Are they worth the cash?
@UndergroundPaintKing6 күн бұрын
I do have a inflatable booth and they work and can be worth it in my opinion but like everything else, there are pros and cons to it
@sgtrickards56836 күн бұрын
@UndergroundPaintKing ok. Ok. I'll do some research. Do you have a video about it? Do you have a favorite brand? What should I look for? Maaaannnnn, bro...I really appreciate the quick response. I'm trying to get back into painting, and you're helping guide me. I know I ask a lot of questions. I don't mean to annoy.
@UndergroundPaintKing6 күн бұрын
@@sgtrickards5683 here is a video on one from Vevor that might help you get a idea of what to look for kzbin.info/www/bejne/sKuVco2NmM6iiJIsi=7lza5ECUY3NYtzu7
@sgtrickards56836 күн бұрын
@UndergroundPaintKing thank you. For real.
@UndergroundPaintKing6 күн бұрын
@@sgtrickards5683 you’re welcome!
@stewiegriffin9446 күн бұрын
Shiiiiiiiiiii
@UndergroundPaintKing6 күн бұрын
Appreciate you checking out the video!
@charleshutchings93557 күн бұрын
I just watched this video after ordering this gun today. I was mainly looking to see how to set the gun up, but it turns out you used the same compressor my brother has. I have to repaint the hood on his truck using single stage paint, as he is totally against base/clear after it started falling off from a bad repair job a body shop did on it after a wreck. I painted it last year with Rustoleum spray cans, but it's peeling in one place. I decided to get this gun, and strip the hood, then put good paint on it. Now I have to go watch your video on setting up the compressor. Thanks for the videos UPK!
@UndergroundPaintKing7 күн бұрын
Glad to hear the videos are helping out 💯💪🏾
@rongamble98847 күн бұрын
I sprayed some FC740 over the weekend with the black widow gun
@UndergroundPaintKing7 күн бұрын
What’s your thoughts on it?
@rongamble98847 күн бұрын
@@UndergroundPaintKing I honestly can really tell a difference between it and the FC710 I'm getting ready to step up and spray some CC200 on next car
@UndergroundPaintKing7 күн бұрын
@@rongamble9884 nice 💯
@rongamble98847 күн бұрын
@@UndergroundPaintKing I'm trying to step up on all my products with Sherwin Williams I stopped using FP410 primer and paying a little more to start using SU521 so much better and it works great as a sealer also
@UndergroundPaintKing7 күн бұрын
@@rongamble9884 it’s always good to start with the lower grade stuff and work your way up to the better stuff in my opinion
@jojoglemond7 күн бұрын
Very nice, you've given me confidence to pull the trigger and do it myself.
@rogeliogamboa76448 күн бұрын
Sir, thank you for a very helpful video - I have a 5 CFM compressor with 50 liter tank and was hesitant to buy a quality HVLP gun in case my compressor wouldn't cope up - but it seems it won't be a problem - thank you again
@UndergroundPaintKing7 күн бұрын
You’re welcome and I’m glad the video was helpful!
@sgtrickards56838 күн бұрын
I gotta get myself a larger compressor. I have a 6gal Bostich. SMH.
@UndergroundPaintKing8 күн бұрын
A larger compressor will definitely help depending on what you’re trying to do!
@sgtrickards56838 күн бұрын
@UndergroundPaintKing I have a small trailer I gotta paint here soon. Like a mower trailer. Nothing crazy. Looking at a 29 gal. I have the a610 gun.
@corygene64778 күн бұрын
How long did you let the 1st base color dry before you taped it off to do the 2nd?
@UndergroundPaintKing8 күн бұрын
I normally wait 30 minutes to a hour
@birdslappy8 күн бұрын
would this setup also handle smaller clearcoat jobs like it does with laying paint, like fenders, doors, a bumper?
@UndergroundPaintKing8 күн бұрын
It should be able to handle small jobs for you!
@birdslappy8 күн бұрын
@@UndergroundPaintKing Nice! Thanks for the reply! I'm thinking of using a 20 gallon compressor with a LVLP to paint a whole car section by section to make sure I have enough pressure. From my understanding doing a whole car in sections is the way to go when using a compressor under 60 gallons to give it time to refill right?
@UndergroundPaintKing8 күн бұрын
@@birdslappy that’s a good process but it’s possible to paint the vehicle without having to wait for the tank to fill also
@birdslappy8 күн бұрын
@@UndergroundPaintKing okayyy nice! Thanks again! Love the vids
@UndergroundPaintKing8 күн бұрын
@@birdslappy you’re welcome and I’m glad the videos are helpful ❗️
@TXprimeFishing138 күн бұрын
I need your help…… I need to remove Buffer Swirl Marks that someone put on my Brand New Toyota 4Runner TRD-OFF ROAD PREMIUM in the Underground Color. I would like to get a Cordless Polisher so what do you recommend? Thanks for your help!!!
@UndergroundPaintKing8 күн бұрын
If you have access to a Harbor Freight, I would look into a Bauer Cordless polisher, that should work out well for you
@TXprimeFishing138 күн бұрын
@@UndergroundPaintKing ok, thanks for your help!
@UndergroundPaintKing8 күн бұрын
@@TXprimeFishing13 you’re welcome!
@thedogefather9 күн бұрын
dang bro looks great! hope to find someone in kentucky hook me up with quality paint work like that. working on my 98 next year get top done maybe new paint /pin stripe
@UndergroundPaintKing9 күн бұрын
I appreciate you checking out the video and good luck to you on your project 💯💪🏾
@lesliwells54339 күн бұрын
ONCE AGAIN THE UPK HAS DONE IT AGAIN, AND AGAIN, AND AGAIN, YOU CAN COUNT ON THE UPK THE PEOPLE'S CHAMP ❤
@UndergroundPaintKing9 күн бұрын
Appreciate you Lesli💯
@lesliwells54339 күн бұрын
@@UndergroundPaintKing WORD UP YOU THE MAN UPK
@lesliwells54339 күн бұрын
ANOTHER GREAT VIDEO UPK,IF YOU MAKE A MISTAKE, JUST FIX IT, LIKE THE UPK DID,PEACE ❤
@UndergroundPaintKing9 күн бұрын
Appreciate you Lesli, peace ❗️
@yeayeasautoadventures9 күн бұрын
I sure like those old montes king
@UndergroundPaintKing9 күн бұрын
Thanks JoCo, I hope I can get them back to glory days ❗️
@philipbaker23029 күн бұрын
You know I always like your videos.
@UndergroundPaintKing9 күн бұрын
Thanks Philip, I really appreciate you ❗️
@larrymurphy6139 күн бұрын
Nah bo we need that info talk that talk
@UndergroundPaintKing9 күн бұрын
I got you Larry 💯 I appreciate you checking out the video ❗️
@SteffsGarage9 күн бұрын
Just tried this system instead of my devilbiss dekup and the spectrum is awesome and a third the cost
@UndergroundPaintKing9 күн бұрын
Glad to hear the spectrum system worked out for you ❗️
@PutUp36510 күн бұрын
Damn dragging on.. like listening to my mom tell a story, just get to it dawg.