good video....no horsing around with telling his whole life story...he gets right to it...step by step...well done.
@yamahaxs65014 жыл бұрын
Sam is the man! I stored my lower ball joints in my deep freezer overnight, then pulled them out right before I pressed them in. I think it helped a lot. I just did this last month on my C10, well worth it.
@BROTHERSTruckPartsTV4 жыл бұрын
Great Tip!
@anthonysao88302 жыл бұрын
Do I need a brake booster when installing this kit?
@yamahaxs65012 жыл бұрын
@@anthonysao8830 it's up to you. I run mine with a wilwood master, no booster. I like manual brakes much better
@GIGUNS-03415 жыл бұрын
Been following you since shadytree garage back in the 90's
@808chevykev5 жыл бұрын
Damn it! I knew he looked familiar 👊
@lildeena15 жыл бұрын
GI GUNS 0341 I thought his voice sounded familiar
@kensomers8936 Жыл бұрын
Thank you . I am now hooked on your videos . Great explanation. Straight talk.
@BrutusTJustice4 жыл бұрын
Nice job.Great video.It's good to see you still turning wrenches.God bless.
@BROTHERSTruckPartsTV4 жыл бұрын
Thank you sir!
@jefferykaighin70396 жыл бұрын
Great how to video that shows the simplicity when going disc. I wish I had the enthusiasm the instructor has!
@ronstickle46946 жыл бұрын
Sam is the Man!
@MrRotaryrockets4 жыл бұрын
Great Job..I hate to be picky but when you swung the left rotor straight..you had your hand on the tin backing plate and you bent it towards the rotor I have seen this a lot on cars I have repaired..I always bend them back and away from the rotor..because if they rub or a rock gets stuck under them they make all kinds of weird noises..Thanks for the video
@clicks594 жыл бұрын
The correct way to break ball joints and tie rod ends loose
@NorthGaLife4 жыл бұрын
I miss Shade Tree Mechanic.. Memories
@BROTHERSTruckPartsTV4 жыл бұрын
Sam was a great teacher!
@mahdavimotorsports2427 жыл бұрын
Absolute great job!
@jimmysapien99613 жыл бұрын
Yes great job
@marshallmalone38706 жыл бұрын
Nice job!!!!
@BROTHERSTruckPartsTV6 жыл бұрын
Thanks!
@joshuarodriguez845 жыл бұрын
I am starting my brake conversion on my 1965 chevy . The video helps ! Thanks for sharing ! I'm going to do ball joints and tie rods as well . Thanks again !
@BROTHERSTruckPartsTV5 жыл бұрын
You bet! Have fun with the project.
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTVAWSOME Show and Tell 👍🏻 I’ve used the Floor Jack also to take off the Spindles . Just make Sure you have a Motor In the hood . The weight will help !
@shredfast48194 жыл бұрын
I have a 1962 chevy C10 which I will be putting disc brakes on for the front, is there a vehicle that I can snatch the spindle from used that would work for my application, or will I have to buy them new? Or is there an adapter bracket that I can buy instead?
@BROTHERSTruckPartsTV4 жыл бұрын
There's nothing out there that will bolt straight on to the '62, you're stuck buying disc conversion spindles that are specific for your truck.
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTV I Agee - that’s what I am going to do to my 66’ -soon ...
@gboots90093 жыл бұрын
Down the road when parts wear out, are calipers, pads, and rotors available separately? Seems like a nice kit, but not if you can't maintain it. I checked the website and didn't see the parts available seperately, but maybe I looked in the wrong place.
@BROTHERSTruckPartsTV3 жыл бұрын
Yes, completely replaceable using later model Truck replacements.
@JamesWilliams-os5tk Жыл бұрын
How much do a conversion kit cost for a 69 Chevy C10 front disc brake
@BROTHERSTruckPartsTV Жыл бұрын
Check our current prices at www.brotherstrucks.com
@rncboy23 жыл бұрын
What master cylinder did you guys use with this conversion that has a brake booster.
@BROTHERSTruckPartsTV3 жыл бұрын
We use one the ones available here: www.brotherstrucks.com/Power-Brake-Conversions/products/2142/
@rubenfilippus29564 жыл бұрын
I have a 67 C10 truck but it's having small wheel studs.will the big studs fit in the same drum and Axle?
@BROTHERSTruckPartsTV4 жыл бұрын
Ruben, the studs should be the same size? Why does your truck have small studs? Doe you mean it has 5 studs instead of 6? We have conversions for 5 lug and 6 lug trucks at www.brotherstrucks.com
@rubenfilippus29564 жыл бұрын
@@BROTHERSTruckPartsTV it's having 6 studs which 11 mm.i wasn't trying to fit the nuts from Ford f100 but they can't fit.and I tried to fit the nuts from my 67 C10 truck to Ford f100 and they are small
@rubenfilippus29564 жыл бұрын
@@BROTHERSTruckPartsTV I mean the wheel bolt and nuts
@BROTHERSTruckPartsTV4 жыл бұрын
@@rubenfilippus2956 our 6 lug units have 7/16" (11mm) studs, our 5 lug units have 1/5" studs, does that answer your question? If you need more help with this PLEASE CALL US at 800-977-2767, it is very difficult to do technical troubleshooting through KZbin comments.
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTV Exactly
@victoriomontoya11108 ай бұрын
Will this kit fit stock steel 6 lug rims on my 1968 chevy c10? Id like to convert to disc brake and keep my powder coated 6 lug rims and just ordered whitewalls so definetly dont want to change rim size. Thank you for informative video.
@KevinnoelAcosta Жыл бұрын
Buenas tardes muy buen video pero de qué modelo son los mangos o de que año
@mariohermosillo63894 жыл бұрын
No life story for sure.
@reesegagne395629 күн бұрын
Can someone give me some advice, i have a ‘68 k20 4 wheel drum non power brake. I want to convert it to front wheel disc brakes and add power brakes. I have no clue where to start being that nobody sells kits for 4x4 trucks.
@lildeena15 жыл бұрын
website says these won't fit stock wheels. Are these 15 inch rally wheels stock and will this kit work?
@BROTHERSTruckPartsTV5 жыл бұрын
It really depends on the wheels offset when you are running 15". Contact our office at 800-977-2767 and we'll help you sort it out.
@bigbadbrad11005 жыл бұрын
Will 15” rally wheels fit over the 12” rotors?
@BROTHERSTruckPartsTV5 жыл бұрын
The rotors in this kit are 11" and they will fit with a 15" rally. 12" rotors will most likely NOT have enough clearance on most Rally Wheel offsets.
@Bondovw3 жыл бұрын
I have a 68 suburban all stock. Will this kit fit with my original wheels?
@opinionsvary31324 жыл бұрын
Great vid. 😊 Question from Australia mate; *is it the same conversion on the 1977 454 C30 ? Or is it a different conversion? Regards Steve
@BROTHERSTruckPartsTV4 жыл бұрын
It would be a different conversion on a C30. Unfortunately we do not carry that conversion at this time. Sorry!
@opinionsvary31324 жыл бұрын
@@BROTHERSTruckPartsTV that's cool mate. It's great that you took the time to reply. Thankyou 😊
@stupickles51224 жыл бұрын
If I’m doing this on my 69 c10 do I need to do anything to the factory master cylinder/booster?
@BROTHERSTruckPartsTV4 жыл бұрын
You need to change the factory master to a Disc/Drum master that will deliver proper pressure front and rear as well as hold residual pressure in the front. Not sure, but you might be wanting to convert to Power Brakes at the same time. Check out our website www.brotherstrucks.com for all the possibilities.
@stupickles51224 жыл бұрын
BROTHERS Truck Parts thank you
@TomJones00654 жыл бұрын
I know this is an OLDER Video, and it does look interesting but I have a 1970 Chevy Suburban 4X4 and I am looking for info how to CONVERT That from FRONT Drum to DISC. I have done the 2 wheel drives, and THATS ALL the INFO out there anymore. So If anyone can help PLEASE LET ME KNOW! Thanks!!
@BROTHERSTruckPartsTV4 жыл бұрын
As far as we know there is no commercially available 4x4 Disc conversion. Most guys switching pre-1971 4x4's to disc just use a front axle from a 1971 or later truck. Sorry we couldn't be more helpful.
@TomJones00654 жыл бұрын
@@BROTHERSTruckPartsTV Ok, thanks anyway. I was told by one you tuber "as long as its a dana 44 the spindles should be the same, without switching the hole diff/rear end, being as I can NOT find anything with disc front end on it. So I'm kinda in a rut, but time will find a way! thank you..
@luckyhouston10543 жыл бұрын
I'm working on a 72 Chevy c 30 with duallies. Trying to replace the rotors. I suspect the upgrade was already done. None of the rotors I have ordered fit. The rotor itself is too thick for the calipers. Help
@BROTHERSTruckPartsTV3 жыл бұрын
Call our shop and lets see if we can help figure it out. 800-977-2767
@eanherniman92426 жыл бұрын
Wow what a gentleman easy to follow
@edwardnunez2183 жыл бұрын
What size rim/wheel will fit on the 66 front disk brake conversion site only says stock(15”)won’t fit but will a 16” fit?
@BROTHERSTruckPartsTV3 жыл бұрын
99% of stock 15" or bigger wheels work. There are VERY few wheels that won't. We've actually never come across any that don't.
@richardmindiola2655 Жыл бұрын
Where can I get a conversion kit for a 1940 Chevy pick up?
@wayneh87673 жыл бұрын
awesome, remember Sam back from Shadetree mechanic!
@BROTHERSTruckPartsTV3 жыл бұрын
He is a true PRO!
@yamahaxs65016 жыл бұрын
great video. Sam does a great job.
@zzaparniuk43742 жыл бұрын
Will this kit work for a 1965 C20?
@BROTHERSTruckPartsTV2 жыл бұрын
Call our customer service department at 800-977-2767 amd one of our techs will help you out!
@1jjwilliams4 жыл бұрын
I have a 1987 GMC Sierra S15 Mini truck and I'm trying to do a conversion on the rear drum brakes is that a hard task and do you have a video for this type of vehicle 🤔
@BROTHERSTruckPartsTV4 жыл бұрын
We don't do anything for the mini trucks, sorry!
@meza52072 жыл бұрын
What difference does the dropped spindle have from the stock height ? does it make a difference when lowering the truck ?
@BROTHERSTruckPartsTV2 жыл бұрын
2.25" drop
@vvvv-lu8zi Жыл бұрын
What the tie rod end?
@BROTHERSTruckPartsTV Жыл бұрын
Depends on what conversion you are doing.
@benmitchell26426 жыл бұрын
Where can I buy a proportioning valve?
@BROTHERSTruckPartsTV6 жыл бұрын
we have a few options here on our website: goo.gl/KtWYdK
@ozcorr9092 жыл бұрын
Is it the same kit for a 65 as 72 c10 or are they different?
@BROTHERSTruckPartsTV2 жыл бұрын
Different kits. Balls joints, tie-rods, etc are slightly different through the years, so the parts in the kits also vary.
@rojeliopenajr.12776 жыл бұрын
Im gonna be upgrading in the next week to disc brakes All the kits I dont see anyone including a backing plate. Do I really need one? It's for a 1970 c10
@BROTHERSTruckPartsTV6 жыл бұрын
It's not necessary. It was a factory installed item in the 60's-70's and it's not common to put them on when doing a conversion.
@rojeliopenajr.12776 жыл бұрын
@@BROTHERSTruckPartsTV great thank you.
@karenkain91653 жыл бұрын
What factory steel wheel will work with this brake conversion - working on a 65 C10. Thank you.
@BROTHERSTruckPartsTV3 жыл бұрын
Pretty much any of the 15" wheels will work.
@edwardnunez2183 жыл бұрын
So 15” stocks will fit?
@BROTHERSTruckPartsTV3 жыл бұрын
@@edwardnunez218 yes!
@justinjacobson75559 ай бұрын
Holly buying brothers sucks
@coltonostmann2586 жыл бұрын
Couple of questions.... i have a 63 im slowing fixing up, i am interested going to disc brakes on the front. Would i need to replace the original booster? And will the fit 6 lug gm wheels?
@BROTHERSTruckPartsTV6 жыл бұрын
In '63 your factory brakes had a single cylinder master which we always recommend you convert to dual cylinder for safety reasons... so YES, we would say replace the original Booster/Master combo. As for the 6 lug wheels, our disc brake conversion will fit behind MOST 15" factory 6 lug wheels. If your wheels are 14" however, there is almost ZERO chance of them fitting with the disc conversion.
@BROTHERSTruckPartsTV6 жыл бұрын
UPDATE: After a doing a little research regarding wheel fitment, we've found a few variables that make some 15" wheels NOT FIT with the disc brake conversion. Primarily, if your 15" wheel has only 3 "nubs" on the center of the wheel to retain a hubcap then your wheel will probably NOT WORK with disc brakes. If your 15" wheel has 4 nubs for hubcap retention, then it WILL WORK with disc brakes. Thank you for asking, we hope this helps.
@Lichor23696 жыл бұрын
I had to go 16" min went with 17" wheels for my upgrade 6 lug also
@georgecurrier50186 жыл бұрын
How can I convert front drum brake to disk by using Parts from wrecking yard.
@robgaskins81815 жыл бұрын
@@georgecurrier5018 I'm wondering the same thing. I have a 69 GMC, 6 lug drum brake set up. It would be great if I can pick up from a junkyard everything I need.
@Rogue_wyo4 жыл бұрын
these are great, but what about us K vin guys? do you have a conversion for the 4x4s?
@BROTHERSTruckPartsTV4 жыл бұрын
Us K guys (we have 3 here at the shop) only option at the moment is to swap axles. No kits are currently available (Sept 2020)
@Rogue_wyo4 жыл бұрын
@@BROTHERSTruckPartsTV Might look into seeing if 71 and up small bearing blazer stuff would bolt on. I will link a video. would be great to see as a kit from you guys. kzbin.info/www/bejne/jqbMXoB-hLuLba8
@BROTHERSTruckPartsTV4 жыл бұрын
@@Rogue_wyo Yessir, thank you buddy! We'll check into this and maybe something good will come from it. Appreciate it!
@BROTHERSTruckPartsTV4 жыл бұрын
@@Rogue_wyo Tossed this over to the product development guys and they already knew something about this. It sounds like the small bearing spindles would have to be manufactured before a kit could be offered. Otherwise, pre-1970 K guys would have to go out and get a set of spindles from a junk yard, etc before they could mount all the parts for the conversion. This doesn't appear to adapt onto the factory drum spindle.
@Rogue_wyo4 жыл бұрын
ya the video mentioned spindles from g2.
@russlowe83232 жыл бұрын
How long does it take to do this dis brake conversion ?
@BROTHERSTruckPartsTV2 жыл бұрын
Usually about 6-8 Hours.
@Thatdudedoes6 жыл бұрын
Great video! Question for you. Do I need a new Master Cylinder and booster to install this kit? Or will it work with my original Booster/master cylinder? I know I would need to add a proportioning valve right?
@BROTHERSTruckPartsTV5 жыл бұрын
Ideally you should at least change the master cylinder. Disc type master cylinders have a different bore size than those used in a drum brake system. Additionally, most disc type maters cause a small amount of residual pressure to remain in the lines to keep the pads from retracting too far.
@Thatdudedoes5 жыл бұрын
@@BROTHERSTruckPartsTV Thank you so much for the reply! Definitely going to upgrade the master cylinder. You just earned my business. Thank you again...
@bruceleeroy8724 жыл бұрын
Awesome video!
@BROTHERSTruckPartsTV4 жыл бұрын
Thanks for checking it out!
@cameltoeinspector60153 жыл бұрын
do I need a bigger master cylinder?
@BROTHERSTruckPartsTV3 жыл бұрын
You don't need a larger one, but you probably need a different one.
@ar902426 жыл бұрын
Where can I buy this for a 1971 C10 half ton, Long bed, 5 lug?
@BROTHERSTruckPartsTV6 жыл бұрын
We have a disc brake conversion that you can find on our website here: www.brotherstrucks.com/71-72-WILWOOD-DISC-BRAKE-CONVERSION-5-LUG/productinfo/DBU5L25/ Another option is the Complete Big Brake Kit with Power: www.brotherstrucks.com/63-87-COMPLETE-BIG-BRAKE-KIT-WITH-POWER-5-LUG/productinfo/CBBK875/ Please feel free to call us during regular business hours to make sure this is the exact kit that will work for your application.
@ar902426 жыл бұрын
BROTHERS Truck Parts you guys are awesome. Thanks guys!!!
@ar902426 жыл бұрын
BROTHERS Truck Parts one more thing guys, I don't know much about breaks except replacing them, I was wondering if these come with dust seals, I see in the description that it states it has dust caps, are those the same thing? Hey and thanks for the quick response. I wasn't expecting a reply so fast.
@BROTHERSTruckPartsTV6 жыл бұрын
Yes they do!
@grumpy1962R Жыл бұрын
What about the rear
@JP-xg8cd6 жыл бұрын
Great video but I was nervous as all hell when he was pulling the lower ball joint, I kept looking at the spring wondering when it was gonna pop out and him him in the head glad everything worked out great!
@jimmysapien99613 жыл бұрын
Yes you would have to have the Motor in the vehicle to do that !!!!
@neilhounshell28925 жыл бұрын
why did you use 2 different trucks for install ?
@BROTHERSTruckPartsTV5 жыл бұрын
We didn't, it's the same truck start to finish.
@travismcminn98156 жыл бұрын
Fix the backing plate....... bent it at the end of the show
@BROTHERSTruckPartsTV6 жыл бұрын
Good eye!
@6806goats14 жыл бұрын
68 C30 disc brake swap please. Guess I should look into a cross member change from a 73-87 C-30
@BROTHERSTruckPartsTV4 жыл бұрын
Yeah, bummer nothing is available for the C30. Your best bet is to piece one together from a later year model truck like you said.
@mkcap89485 жыл бұрын
Would this kit work on my 66 gmc k1000?
@BROTHERSTruckPartsTV5 жыл бұрын
Our disc brake kits won't work on a 4x4, 2wd only. Customers who have converted to disc on 4wd trucks normally just swap the axle for a later axle with discs.
@mattwoody10893 жыл бұрын
Good work
@BROTHERSTruckPartsTV3 жыл бұрын
Thank you!
@rockyp5446 жыл бұрын
Just had mine done. Pretty trick...love em
@neilhounshell28925 жыл бұрын
should i put front and back and what is the best price to do the job or kit
@BROTHERSTruckPartsTV5 жыл бұрын
Adding front disc brakes is a safety and convenience step that most classic truck enthusiasts do. however, adding rear disc brakes is up to you and ultimately what you want your build to be. As far as install cost, we would estimate it between $400-$750 depending on the shop you choose.
@pdan36766 жыл бұрын
Will this disc brake conversion required Power Booster to assist braking?
@BROTHERSTruckPartsTV6 жыл бұрын
You can do a disc brake conversion without adding power providing you run the proper master cylinder and proportioning valve. However, we would recommend doing both at the same time.
@braveonefightfortheright9055 жыл бұрын
What’s the assembly kit number to order?
@BROTHERSTruckPartsTV5 жыл бұрын
On this truck we used a 6-Lug "Deluxe" conversion, but you might want to check out the other options here and decide what you prefer www.brotherstrucks.com/Front-Disc-Brake-Conversions/products/2139/
@robert.williford5274 жыл бұрын
Do you guys make disc conversion kits for 67-68 3qtr ton chev pu?
@BROTHERSTruckPartsTV4 жыл бұрын
You can convert it to disc, but first you have to convert it to 1/2 ton parts. It's really not that big of a deal, just an extra step for the 3/4 ton guys.
@robert.williford5274 жыл бұрын
BROTHERS Truck Parts ok but I’d like to keep the 8 lug wheels front and back; any advice?
@BROTHERSTruckPartsTV4 жыл бұрын
@@robert.williford527 That can be done, but the specifics of that conversion are too much to get into in KZbin comments. Call our shop at 800-977-2767 and have one of the Tech Guys go over it.
@travisfasano7756 жыл бұрын
My lower castle nut won’t tighten enough to get cotter pin on- can I use ball joint press to tighten down spindle onto joint?
@BROTHERSTruckPartsTV6 жыл бұрын
you'd be better of to back it off a little bit to the next notch that the cotter pin can be put through instead of trying to use a ball joint press.
@travisfasano7756 жыл бұрын
No my problem is during assembly. My new ball joint won’t fit into my New lowering spindle. Like I can’t even thread castle nut at all to get to cotter pin.
@BROTHERSTruckPartsTV6 жыл бұрын
You have the wrong spindle then. They make these spindles with various different sizes/tapers to accommodate particular years of ball joints that were different sizes. It sounds like you have a spindle that's got an early size tapered hole. If you bought them from us then call our Customer Service at 800-977-2767 and let's get it handled.
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTV I agree Omggg
@DaRealArtist6 жыл бұрын
Great video. What’s the torque specifics for the spindles?
@BROTHERSTruckPartsTV6 жыл бұрын
Roger, typical tapered bearings can be manually adjusted using this method: "... in the case of a conventional truck non-driven wheel with a single adjusting nut design, manual setting involves tightening the adjusting nut while rotating the wheel until a slight bind is felt. Then the adjusting nut is backed off 1/6 to 1/4 turn to the nearest locking hole or sufficiently to allow the wheel to rotate freely with some minimal end play. The adjusting nut is then locked in this position. Skill and judgment are required to determine when the wheel binds slightly in rotation." For more on this subject you can visit www.timken.com/wp-content/uploads/2016/10/5556_Bearing-Setting-Brochure-1.pdf Thanks for asking!
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTV exactly
@jesustrevizo31485 жыл бұрын
Didn't he have a show
@BROTHERSTruckPartsTV5 жыл бұрын
He hosted Shadetree Mechanic for 15 years before hosting Two guys Garage, Motorhead Garage and Sam's Garage. He retired last year.
@jimmysapien99613 жыл бұрын
@@BROTHERSTruckPartsTV glad he is taking easy ! I’m trying-to myself