228cc Stroker Build 23HP Tillotson

We build a stroker honda clone! Starting with a Tillotson 225cc racing block, we add a 0.040" longer crankshaft, bumping this high compression engine up to 228ccs of displacement. This is no doubt one expensive mini bike engine, but it makes an incredible amount of horsepower and torque in a small, lightweight, brand new, and reliable package. There's no official number on how much horsepower this small engine makes, but Taylor at Go Power Sports is expecting 23-24. Small engine performance has come a long way in the last 5 years!
Thanks for Watching!
Facebook: goo.gl/VR6mh2
Instagram: bit.ly/3T8njaF
----------------GO POWER SPORTS PARTS IN TODAY'S VIDEO---------------
228cc Tillotson kit: bit.ly/2zQCG3w
Go Power Sports: bit.ly/3QKyODE
NEW MERCH: www.cars-cameras.com/
Equipment we use: www.amazon.com/shop/carsandca...
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. CARS AND CAMERAS, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL CARSANDCAMERAS CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Cars and Cameras makes no representation about the sufficiency of any safety precautions and equipment used in this video.

[@motoman22atgmail]

3:02. Put the case in the oven, make it hot. Put the bearing in the freezer, make it cold. Bearing falls right in...

[@StupidEarthlings]

+100. That's bearing 101 right there. And isaac, ya really shouldn't "hammer" any bearing anywhere. ;)

[@ghomerhust]

yep, i was just thinking they should get a little mini fridge in there for bearings. thats now my family has done it for years

[@JEGARAGEOFFICIAL]

Really! The bearing just falls in??

[@motoman22atgmail]

J&E Garage ok ok ok, it goes in SO MUCH easier that it seems like it falls right in. Better?

[@larrytaylor2903]

@@JEGARAGEOFFICIAL Yes, with the proper temperature differential, they just drop in. No big deal.

[@harryfritter8266]

You could buy a retired shipping container, 20'-40' they start at like $1500. And put it on the other side of the shop. Then you could place it about 12 feet from the building and build a roof/carport in between. Then you'd have outside covered workspace and secure storage too. Love your videos!!

[@theupscriber65]

I built a 16x12 fully enclosed gazebo for $500 including floor joists and roof.

[@rpietros]

@@theupscriber65 what did u use plastic wrap for roofing?

[@theupscriber65]

@@rpietros LOL I do wrap the interior with plastic wrap during the winter! And the roof is transparent (tinted) roofing panels from Menards. So it's more of a 3 seasons room. The walls are prefabricated (purchased used from Craigslist for $300). I also already had a pre-existing slab so I just had to build footings up from there for the floor joists. Here it is kzbin.info/www/bejne/hqrGiYGXa9iqfKM

[@stykytte]

@the upscriber You actually went and filmed it. I never give the haters the time of day in YT comments, but you went and delivered proof. Nice one.

[@LifeWithJay22]

kzbin.info/www/bejne/iorTaIadhMR5qLc

[@Bri-tg6xr]

I really appreciate how you guys utilize each other's skill sets, I like KZbinrs who all contribute to the video. Far too often you never see the guy behind the camera and it's one main person doing all the work even though the videographer and editor needs to be recognized as well. Nice work!

[@matthewf1979]

That’s a great power to displacement ratio. Especially for a pushrod, two valve, carbureted engine.

[@BGmovies.]

Hoo g ga jhfyf hoo eh hd nag eh r FX didto di at eroplano nga daw ang imo nga gusto mo kaunon kay nagutom nagid nag tangla sa langit sa langit sa eh hd sa hi normal e

[@perfectcell7995]

@@BGmovies. one more time in English plz

[@zuestoots5176]

@@perfectcell7995 something about looking up and airplane. Google cant even translate whatever the fuck that shit is

[@IllegallyAcquiredKIA]

You should see the 70cc 40hp moped engines they can build

[@funkydunkygaming]

Bruh you ever heard of dirt bike engines?

[@Lejackal]

Why am I so addicted to this channel..42 years old always been a tech guy not an engine or car guy....but recently anything in the maker genre has me addicted....this channel being one of my guilty pleasures....

[@ZaddyZach83]

I can tell they will have a fun time at the track with that engine 🤣

[@catsbyondrepair]

Till it blows up😂

[@tjlabbee7856]

Tech tips from Isaac... I like it!

[@R4MP4G3RXD]

Yeah but the he goes on to grind the crank and the camshaft 😂😂😂

[@BryanthePlumber]

The reason I like this channel so much is this is still how I build stuff. I dont have fancy equipment, I still hammer my bearings in with whatever I can find same as you guys. But in the end, the product speaks for itself. Lots of character, and something you can be proud of.

[@edh7492]

The engine builds are what got me hooked on the channel and a big part of why I keep coming back. Proper tuning, smaller but the same rules apply. Fine work gents.

[@calvinwright1816]

You can also build up the area around the valves on the head with weld, to reduce the volume, and increase the compression. Between shaving the head a high compression piston a thin valve gasket and building up the extra area with weld, You can get the compression high enough It will sound like real dirt bike. And have power for days, some stock dirt bikes come with 13: 1 compression So you should be able to get close with a built motor. Something I hope to see in the future! Sweet little build you got there 👍🙂

[@AutumnsAdventure15]

Isaac is like a teenager in these videos. He was so happy when jon said that he had icecream sandwiches!!! I think you have to find something that helps keep you young in this world. I've been building my 5 year old daughter a few mini toys to play one. She has a rocket. An atv. I'm working on her "chopper" mini bike right now. Then taking a pedal car and making her a drift car!! Love the videos and keep on building!!!

[@CarsandCameras]

Just a few years ago it was impressive to make 12 horsepower with off the shelf parts with one of these small block Honda clones, yet here we are in 2020, making nearly 24 horsepower. Where do you think the upper limit of reliable power will be for these Honda Clones? This is an expensive engine no doubt, but you can’t beat it for size, potency, weight, and simplicity. A predator 420 would tick a lot of these boxes, but it weighs over two times more than this engine, and it’s almost double in physical size. A similar situation goes for a smaller dirt bike engine- small(ish), not really light weight, and significantly more expensive than this setup (for a new engine). I’m not knocking big block Honda clones or dirt bike engines, I just think it’s really interesting how far these small blocks have come, and how they’ve carved a distinctive place for themselves in the world of small motorized vehicles.

[@kristianellis1858]

Well said and amazing.

[@googleitdepartment1371]

greaat video

[@brennensbuildsmoore5537]

Hell yeah, I just made a race mini bike and it is amazing, you guys helped me with what to do for building it

[@quevicular]

I think youve hit the limit otherwise you would have to heliact the block in some places so it wont grenade

[@brennensbuildsmoore5537]

Update, I blew it up 😂

[@trecedaves3159]

Y'all motivated me. I am pulling the trigger on a used kubota diesel out of a tiny lawnmower tractor. Going to build a vw bus monster truck. I have all the metal and several old carts to scavenge parts from. Using a old honda trx tranny to have reverse. Plan is more baja look but monster size. I've watched your channel since video 5, and got more and more motivated to build this. My grandson isnt old enough yet, he is on a 3hp kart right now. But it gives me time to fab everything and let my son try and break it so I can make it safe. The motor is the last piece of puzzle, I was planning on using 2 honda 13hp engines i have but the diesel will be more then enough. Not going for screaming fast, just capable. May end up 4x4 still as the donor trx is a 4x4.

[@samsvintageoutboards6847]

Holy crap!! That things gonna fly!

[@ghomerhust]

that motor sounds NASTY! with a good torque converter, itll for sure RIP

[@samsvintageoutboards6847]

Josh Hust yeah man!

[@samanthafox8273]

When can we buy official Cars & Cameras Ikescream sammiches?!

[@ghomerhust]

oh hell, take my money

[@user-st7rq3sn7v]

sponsored by ice cream sandwiches..........

[@motoman22atgmail]

Tag Blue Bell in this! Best Ice cream Ever Period

[@johnclary729]

@@motoman22atgmail So good that people didn't even care when it was contaminated by listeria and killed some people...

[@abehemry5972]

Sound that out and it sounds really bad

[@megoingfast]

I want an ice cream sandwich now. And, to Dyno your engine on my Dyno.

[@koljag5]

They should take a trip to your dyno some day, I wonder what kind of numbers their builds would put down.

[@lawnmowerdave]

Was about to start working, but then you guys uploaded! Thanks for the consistent videos!

[@ericr9953]

Thank you guys! Back to the basics. 4 mins in and I feel like it used to be.

[@TSGEnt]

Wow guys. A pallet for an engine table, hammer and a sprinkler valve for a bearing press, a Gatorade bottle for a fule tank, and John as the engine mount. You guys do have a lot of fun, don't you?

[@tomhudson1409]

Love your videos, you guys work so well together, cheers!

[@davidkirk-hahler2016]

You guys have inspired me to build a go kart. thank you so much for putting out sum amassing content

[@nathanberry0073]

Love your channel keep up the great builds.

[@hayimhere9604]

Quick and dirty engine table Old episodes: radiator on a bucket New episodes: they build a wooden table

[@YeeThirty]

Great build guys! Nice to see you moving up and doing a bare block build!

[@noahthegodgaming8515]

Love you channel bro! I have bought a 30 series torque converter and a a performance exust for my mini bike thanks to you guys! 😁

[@trevornelson7524]

Awesome video guys.

[@davesonsadventures474]

Awesome build fellas! Great job..

[@thomashoffmann3380]

Love you guy's engine build videos!

[@nhenderson2094]

Love the fact that you guys are keeping this channel backyard friendly with the diy table!!

[@jamesconley297]

Put a tillitson 355a carb on it and run it on alcohol guys if you really want to see it come to life. The last race motor I built was a 5HP Briggs big valve .80 over with flattop wiseco piston horstman 4.485 billet rod. Ran a 11tooth horstman two shoe racing clutch with 8500 stall springs. Man that thing had the torque and HP. It would walk the dog and pick the pups now. Last race my dad ran it busted a new billet sprocket hub on a 1 1/4 live axle now that’s some torque right there. By the next year there were no more tracks to go race at that were close enough to us so we decided to sell and so we did. Had lots of fun racing back then especially more so with my dad. We ran in a class called outlaw class. It’s were you took yard karts built the engines and set them up to handle on a dirt track. The last year we ran the class together we had our karts set up to look like lil mini outlaws with the offset wings on top of the roll cage. Gosh guys I could go on and on. Keep up the great work.

[@sheldonhall4572]

Nothing better than a fresh new motor firing for the first time. Cant wait to see it on the mini bike lol.

[@toadinthehole8085]

Listening to you roll off the modified parts like a boss, was music to my ears . Flat top piston 😁

[@adamtaylor5591]

You guys are the best small engine tubers out there!👍

[@xxgoldantraxxx8461]

Love yall vids keep em coming.

[@elnacho15]

The quality of the vid is a lot clearer I like it

[@crackerjack9608]

oh this engines gonna be beautiful

[@srcobra50]

Man that thing is gona fly. Can’t wait to see. Keep up the great work guys. I’m gone be building myself a stage 3 predator soon. Might get me one of those frames too.

[@JTHuntsman]

That Ice cream bit 😂 awesome video guys! And I’ve been watching for years. The chemistry between you guys is what makes it!

[@milk7036]

Sure do like me some of these engine builds, gives me some inspiration to build one heck of a motor my own.

[@charlesnelson2201]

Nice engine guys. Good going

[@hammerT2997]

Hell yeah good stuff

[@fishinkarts2865]

Yeah that thing on a mini bike is going to be AWESOME!!!!!!!!

[@kcraig51]

Sounds good. That thing was dancing the whatootsie idling on the table!

[@rustyjunk1997]

So glad u guys finally built a table!👍

[@sawyernanook3964]

Sick engine shops looking good

[@tbonebraden9322]

Love the vids👍🏻

[@TheDr.Magnum]

Cars, Cameras, and Ice cream 😂

[@user-st7rq3sn7v]

Not just ice cream..... but a *sandwich*

[@wyattsutphin]

Congrats for the shoutout on yesterday's Klavan show. Glad im not the only DW subscriber here.

[@everythingenginenate966]

Thanks for doing more things on Honda clones!! Friends come and go, but Honda clones never end!

[@lokedog916]

you guys are hilarious, love your videos

[@terminalpsychosis8022]

Wow that is a pretty motor. Awesome piece of engineering there. Sounds awesome too. She's got a cam in 'er!

[@wyattcum5.4]

Great vid boys

[@loosescrewlab3605]

sweeet awesome vid thumbs up !!!!!

[@crazypowersports4020]

Great vid 👍.. love ur channel

[@googleitdepartment1371]

great video

[@Vaioman67]

Doors look great!! Nice table!

[@kennethdispain1807]

Sweet sounds really good 👍 guys

[@justjesse16]

Tech tips with issac. I love it. Very edufunctional vidjya and a lil nitrous thumper on a go cart would be swweeeeettt

[@brentlittlefield2099]

Right on right on right on 🚀

[@yelnatswaltuo]

Love the shade tree techniques.

[@daprankstagangstas2251]

That Bike is going to be a beast with that engine

[@mlbaranowski]

I just built one of these two weeks ago. Only difference is I went with a bigger cam. It has amazing torque and power.

[@hook86]

That thing sounds murderous. Can't wait to see it mounted on a bike!

[@10gaugesbelow]

Yeah 10 seconds in. I love the cheap and quick table! When you need a table you build one!

[@Hazinclayton_007]

Nice art ike!

[@billsfanmc1786]

Cool build guys I am currently build a no suspension off road go kart with a snowblower engine I’m also using snow blower tires should look cool you guys inspired me

[@vojtechgombasan4659]

Yes, you are very good youtubers. I love you

[@octane613]

Man I love ike, dude is such a gem.

[@glockchicken8695]

Finally a good mini bike build

[@christopherhoward2139]

Gosh, that thing is a little beast🇺🇸🇺🇸

[@christophervtec762]

I felt that icecream sandwich moment in my heart 👌 they're amazing 💯

[@aydanangus]

Once the baja truck is done you should make the dingo into a budget version. 150-250cc dirtbike swap, shocks. Posibly a rear end. Just a build idea. Fellow dingo owner that could use some inspiration to get it running and or mod/swap it.

[@killingtime6793]

Absolutely. Hell yes.

[@SportbikerNZ]

That ice cream sandwich cracked me up. I really like seeing these engine builds. So shiny.

[@wogelkrafts]

You had me on the icecream sandwich! GOSH I love those!! 🥰

[@mykee426]

Beast. I really love the monster truck. Put the stroker in it 😎

[@PureCountryof91]

That is a solid table though. I'm pretty impressed

[@josiahw3219]

Wow that's a sweet motor

[@FukTheGovernment465]

Last time i checked they had a Gas ENGINE. Motors DO NOT run on gas...

[@jsswitch8784]

I’m excited for the next Mini Mayhem and Busch Beach! I’m close to Fayetteville, NC and just got a Coleman CT200U EX in really good condition for $250. Can’t wait to ride with y’all!

[@drakrazerclaw5146]

That stroker sounds wicked, can't wait to see the finished product. You may get your wish on seeing 30hp come October, I'm in the process of building a NHRA Pro Stock inspired pocket bike.

[@mitchellfrechmann599]

That thing is gonna do friggin wheelies!

[@speckledjim_]

Back of the net boys 👍👍

[@RandyB1973]

GOBs of torque!

[@twocvbloke]

I like how the music used for the table build was reminiscent of the Tool Time theme from Home Improvement, pretty apt given the engine's getting More Power!!! :P

[@ghomerhust]

-grunts in Tim Taylor-

[@JesseBMotors]

Engine sounds mean 👍🏁

[@slickrickmotowrist1358]

Now this is a video 👍

[@jordonc3379]

That thing sounds like dyno-mite!! hellz yeah! Cant wait to see a mini bike that does 80mph lmao. Show me then I wanna build one. I might be older but I never stop loving going FAST!

[@jarekmace1536]

I'm seeing that table getting modified into a test stand. Mostly just need to rig a fuel tank on a stand with an on/off valve and a throttle grip mounted with a short cable for testing the carb. Add a few holes in the top to keep the engine from walking during start-up and testing, and it's a winner.

[@jasonpetrich4141]

Guys the ice cream edit was very cool 🥶 😎 the videos are awesome, when are you building the mini big rig and lowboy trailer!!!!!! A feller can hope 🙏

[@mikeymike3240]

Do like Allen Milliyard does, he uses his gas barbecue at about 116 degrees, piston liners, bearings etc just fall out or pop in. The man is absolutely amazing, he is a mechanical genius and makes everything he needs in his garden shed, everyone should subscribe to his channel. The man cuts engines in half with a hacksaw, gauges things with his eyes, really, you should watch him.

[@discingaround]

Ike looks like a franken doctor in that intro clip. Here's to some better working surfaces in the shop this summer!

[@daArchitect-]

It's alive!!!!!!!!!!!

[@rileyzandol3150]

Do the freezer and heat gun trick on the bearing next time! Heat the block a bit on the bearing bore and put the bearing in the freezer. You might have to use a little propane tortch to heat the block too. The aluminum will expand a lot and you can just drop the bearing and ensure the bearing is seater all the way.

[@zachblalock9446]

I got my first go karts because you made them look so fun and they are

[@mikenike776]

gotta love the ice cream sandwich I want one now lol

[@cdp50359]

Love to see as mud motor ! ! !

[@rednecktv9105]

Y’all are great you tubers and I just wanna say hi

[@dockmasterted]

Before you forget, ..... You should mark the date you built the "TEMPORARY TABLE" ..... So that years down the road we can look back and see it still sitting on the "TEMPORARY TABLE"! ... lol@me

[@abbeyclapp6259]

Ike always says let me show you how to do it which is why I listen Ike is a🐐

[@joesloan4865]

I made the offer i guess your not intrested. I am the guy that came to one of the earlier events a busco beach. Im the one that was in a golf cart and my son was on a bike. I bought you guys lunch with a 100 donation and never got a thank you. I guess i shouldn't expect any different. Keep up the videos they are great and we enjoy them. Thats why i wanted to try and help you out. I mean its not a big expensive welding table but its a 4foot wide and 9 feet long and a 1600 pound capacity. Good luck guys and maybe you will get what you need at your new place. That is over the top cool