How To Remove A Hemi Intake Manifold Part 2

This video is part 2 of a how to remove a hemi intake manifold.

[@garrettwight1027]

Working on a Jeep Commander with the 5.7 Hemi. Blown head gasket. Didn't know how to properly remove the intake manifold until now. Thank you!

[@redhandedreviews3482]

what is the hole where your oil fill tube is? its close to the manifold...mine is missing something

[@57LHemi]

Not sure man, i guess it's just made like that

[@albundyrocks2115]

If you use the EGR block off plates you have to get a custom tune done to shut it off. Otherwise the vehicle's computer will be looking for it...will run rough and probably backfire. Expensive to eliminate

[@57LHemi]

Yeah that's the reason why I kept mine.

[@Sak-zo1ui]

paul dye it isnt expensive to eliminate.

[@captainobvious5993]

It's running like dog doo doo when I go to wide open throttle it cuts out the rpms go up but it won't accelerate at wide open throttle

[@57LHemi]

The mds solenoids can cause that

[@captainobvious5993]

@@57LHemi just had the new remanufactured hemi installed too

[@captainobvious5993]

How do you get the map sensor harness off the intake it seems it's held on by some type of plastic pin or screw

[@57LHemi]

It snaps in and out, you just pull it up and it comes right off

[@sublimechallenger]

Great video, appreciate you posting this. Is there an intake manifold gasket that needs replacement when putting back together?

[@57LHemi]

On my application no. The gaskets are built in.

[@DonnySRT]

Any tips for removing that brake booster hose?

[@57LHemi]

Yeah you can spray a little wd40 at the base so removal & installation are a little easier

[@ronniefrutschi2011]

Say one thing Mopar has remained true. They built vehicles so a person can work on them

[@57LHemi]

True

[@captainobvious5993]

I'm getting a code p1416

[@57LHemi]

It sounds like you mds is failing

[@captainobvious5993]

The code is performance reactivation misfire cylinder 6

[@captainobvious5993]

I have the intake off now it's just getting bad solenoid out new one in

[@captainobvious5993]

How hard would it be to change out those coolant tubes my are looking rusty on my magnum

[@Sak-zo1ui]

Captain Obvious which tubes are rusty?

[@captainobvious5993]

The two that run under the intake

[@axxo702]

Did you reuse the intake manifold bolts? I've read somewhere they use lockpatch on originals and once taken off will need to be replaced.

[@57LHemi]

Yes I reused the originals,

[@austincase730]

Found this video while researching this exact topic. I’m going to be installing a ported intake manifold from MMX soon on my 5.7 hemi. I noticed the foam between the intake and block/heads. Is that factory(I haven’t pulled my intake before)? If it’s not factory I’d love to know where you got it from and the brand if you remember. Appreciate the video it’s going to be very helpful!

[@57LHemi]

Yes the foam insulator is factory

[@garycorbin2789]

I used a gun barrel brush to clean my EGR tube with dishwashing liquid , worked a treat got a massive amount of carbon tartar out

[@57LHemi]

Cool

[@Noclaff]

Hey man, this short series of how to remove the intake manifold is excellent. Well done! I had a question for ya, I used this video to get down into the valley of the motor where there are two holes that are unused. I believe these are to be used with a proper hoisting plate. Do you know what thread size these holes are?

[@57LHemi]

That I'm not sure....

[@captainobvious5993]

My hemi dropped a valve seat upon startup after fueling up

[@57LHemi]

That's not good at all

[@captainobvious5993]

@@57LHemi so I'm removing the intake to get any pieces of metal out before it gets a remanufactured engine

[@57LHemi]

@@captainobvious5993 good deal

[@MrSmm511]

If you only showed how it will take 10 minutes for all the parts please stop talking about things people doesn’t care about like egr etc

[@57LHemi]

I wish it only took 10 minutes but it dosen't. I hope that help

[@winter_in_vegas_]

There’s actually a specific order to take the manifold bolts out and put them back in. This has got to be the worst instructional video ever. “This tube, coming out of here… got to the thing I’m not even going to bother showing to you because you should just know what it goes to.” Literally why I’m on here looking for guidance.