Audi A3 8P ABS, ESP and Steering assist lights on. Multiple faults... Fault finding and repair.

[@mardina1a]

Same problem in everywhere in the world, bad repair attempts and then problem occours.it's good that you are working on both electronic and mechanic repairments.thanks for that video and informations about trouble codes.Best Regards.

[@LMAutoRepairs]

👍👍👍 Thanks, for watching and for your comment!

[@speckwartburg]

Excellent video thanks Louise. There is no Happy New year without you. THX

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@petecurran3995]

Had this on my Touran and weirdly it caused a dpf regen cycle ever time engine switched on. Where's the logic? Dang VAG! Great vid 👍

[@LMAutoRepairs]

🤣 No logic... 👍👍👍

[@johnf3278]

I always say it. It's great the way you fix things rather than replace.

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@CarsExposed]

Top work Luis great info as always the abs sensor pin could easily been missed if you don’t have yours eyes peeled 👍👍👍

[@LMAutoRepairs]

Absolutely... Attention to detail... Thank you for watching and for your comment! 👍👍👍

[@einfelder8262]

Top work from you too - you commented 6 months before the video was posted.......

[@CarsExposed]

@@einfelder8262 Luis has a Patreon ... if you sign up you can see the videos before it’s published on KZbin , Luis has probably a year worth of videos in advance 100 videos or more www.patreon.com/LMAutoRepairs 👍

[@DodgeCity111]

Some people are misserable, leaving a car over with 10miles range left in the tank. Great fix again.

[@LMAutoRepairs]

LOL I had worse than 10 miles left... believe me...😋 Thank you for watching!

[@nighthawkviper6791]

The sensor should be a line of code in software but they made it a mechanical part that will ALWAYS wear out as it is in the wheel well (LMAO) that is always jostled around from terrible roads(especially in Murica). The sensor makes the front right headlight turn off after 2mins, and the sensor with installation is around $400. 🤣 Degenerate 20th Century morons with their mass production garbage. Every single car ever made is a piece of filth designed to fall apart to make mechanics and dealerships Trillions across the Earth.

[@terminaldiagnostics5576]

Luis what makes them abs ring touch the sensor is corrosion build up behide the ring forcing it outwards you can get the ring for about a tenner did both on my vw golf same set up nice video buddy

[@LMAutoRepairs]

Thanks! 👍👍👍

[@mehdiguitoun6821]

Well, just have to say thanks a lot, it's quite challenging to fix and explain the issue at the same time, only that buzzer is really annoying lol, otherwise great job @LM Auto

[@LMAutoRepairs]

I can't stop it... lol Thank you for watching!

[@Nypartcannon]

Lm auto The super hero we all love fighting the war against part swappers and bandit garages

[@LMAutoRepairs]

It is difficult sometimes though...😔 Thank you for watching and for your comment!

[@neilmurphy845]

Yes I don't know how people like him cope with it sometimes

[@Nypartcannon]

@@neilmurphy845 how do you mean friend ?

[@neilmurphy845]

@@Nypartcannon the way customers bring it to a cheaper person to"fix" it and then bring the car back to the car back to the first guy more expensive lad to fix it because the guy that was just throwing the parts cannon and being a hack installing junk arftermarket dormen parts couldn't fix it as Louis maintained aswell never ever throw parts at stuff always test and verify the wiring circuits and connections are good first I learned that from Keith and Ivan and Eric O

[@RoadRunnerMeep]

Good thing to watch, I own one of these cars now ha. I'm sure I'm going to find multiple faults I don't know of yet

[@LMAutoRepairs]

😊 🤞 Thank you for watching and for your comment!

[@shieldselectrical]

Excellent video presentation and informative narration. Thank you for posting such helpful informatiom

[@LMAutoRepairs]

☺️ Thanks! For watching and for your comment! 👍👍👍

[@MrConspark]

End position -3.5% is the actual position, should be 0% Good video, I have same vehicle needs the sensor changed. Cheers😊

[@PaulysAuto]

Excellent work Luis as usual. Boy they really did a number on that poor speed sensor. Trying to catchup on videos and my goodness am I behind 🙃 Hope all is well with you and your family 👪 Keep doing great things as I know you are! Thanks for sharing your diagnostic experience and approach with us brother!

[@LMAutoRepairs]

😊 We are all good! Hope you are as well! Thank you for watching and for your comment! 👍👍👍

[@timmehlittleloud2251]

Good video as usual. One thing I would say is you were fortunate that the Autel showed the bad sensor waveform. I've had 0778 code, or whatever, and calibration not work because of the tiniest glitches you could imagine. VCDS scope feature usually shows them but sometimes only properly scoping the sensors shows the problem. That's the reason the car needs driving in a straight line for a while, so the computer knows there are no glitches in the wheel speed signals. Until then it instructs the under wheel computer (or if the angle sensor is in the rack and connects straight to the ABS pump it just disregards it) to kill one of the 5v feeds to the steering angle sensor (there are 2, one for transmit IRs and other to the receive IRs - can't remember which one it kills but 7 diodes for each and 2 supplies, 10 pins). This is an underhand way of doing it by VW. There is no explanation anywhere of why the calibration fails - especially when sometimes there are no codes. And the steering to the left then right procedure for the calibration is done right to left to set the limits. Don't you just love German cars 😁.

[@LMAutoRepairs]

😊 👍👍👍

[@dumisanishelembe8056]

😮

[@thejazzvibe9157]

Love your channel brother, Helps me out on the regular. Thanks

[@LMAutoRepairs]

😊 That's great to know... Thank you, for watching and for your comment! 👍👍👍

[@thejazzvibe9157]

@@LMAutoRepairs Hi Bro, I have a question if I may, If I had a faulty brake switch, would it interfere with calibration of the steering angle sensor?. Basically I changed the ABS sensor on a Audi a3 2007, I cleared the code and reset the module, Immediately the steering went 20% heavier. Before that I also replaced all disc n pads and pumped the pedal a few times all the way down, I was thinking maybe this caused the switch to fail. Now I cannot seen to recalibrate the steering angle sensor and the ESP warning is on. Cheers Mate

[@LMAutoRepairs]

Possible... ESP related components are all kinda linked... Fix whatever fault you have and try the calibration again...

[@thejazzvibe9157]

@@LMAutoRepairs Hi Bro, you were spot on, Replaced the faulty ASB sensor and recalibrates the steering angle sensor. It worked and adapted fine. Now the steering feels fine again. Glad it wasnt the brake switch, its located in the servo,

[@LMAutoRepairs]

That's great! 👍👍👍

[@andyamanda5777]

very good ! (again and again and again with you ! ) Well done. My garage reopens tomorrow :(

[@LMAutoRepairs]

👍👍👍 Thank you for watching and for your comment!

[@bitwyipodrozesamochodowetv2995]

Ciekawy film. Mój zdechł na akumulatorze a po naładowaniu pokazał błąd Esp. Na taniej diagnostyce nic nie wychodzi. Sprawdzę jeszcze może jakieś wykresy. Co może być?

[@robiannace6522]

Awesome video I actually just purchased a Audi A6 with only 96000 km on it. Only a week in and I'm having some driving issues. I kinda noticed when driving last couple days but got really bad last night driving home. Down the road and all of a sudden my ESP came on and says see manual along with tracking control symbol along with check engine light. Car runs very rough at idle and shaking as well. Like it's running at only 3 cylinders..

[@LMAutoRepairs]

Scan the car... The logged faults should help you to narrow the problem... Thank you for watching! 👍👍👍

[@robiannace6522]

@@LMAutoRepairs yes I'm taking it in tomorrow to get it looked at. Talking to the guy at the car lot and he said it's a normal probably for the German cars to have either plugs/coil packs gone bad.

[@LMAutoRepairs]

Possibly...

[@the_retired_mechanic]

The magnetic abs rings on the wheel bearing rust underneath and swell up to close the gap with the sensor. Seen that with the live data after the fix wasn't exactly the same on both sides. Aftermarket ones are terrible for this. Hope this info is of use to someone watching. Happy new year my friend

[@cuthburtyes9529]

Happy new year Mr L may God bless you with new and extraordinary ideas and skills to solve car problems . Thanks.

[@LMAutoRepairs]

Thats common on BMW...

[@the_retired_mechanic]

@@LMAutoRepairs yes the rear ones on bmw which have metal slots have the same problem

[@huragandelphi759]

sometimes if the sensors don't want to get out, I just burn them away with a burner 😁, good job👍

[@LMAutoRepairs]

Is also a good option... never had to go that far... lol Thank you for watching and for your comment!

[@-DC-]

You'll never be out of work diagnosing Audi's 🙂

[@LMAutoRepairs]

😊👍👍👍

[@fuzzs8970]

The car forgot Christmas date. Thanks for sharing your work. Nice work by the way

[@LMAutoRepairs]

LOL Was not Christmas when this was done... 😊 Thank you for watching and for your comment!

[@bunsoft2]

Really nice video as usual. Thank you Louis!. Have a great new year!

[@LMAutoRepairs]

Thanks! You too... Happy New year!

[@CarsExposed]

I know where he gets his coffee 😊🤣🤣 Back to the video 👍

[@LMAutoRepairs]

🤣🤣🤣🤣 👍👍👍👍

[@Faizal_Khan]

Lol I have that same Sony stereo, same car and the same power steering problem with these same lights showing. This can't be coincidence 🤣

[@LMAutoRepairs]

😊🤣 👍👍👍

[@agentmarky5493]

😂😂Back in the day a main dealer wouldn’t plug the motor in if a after market stereo was fitted !! Cost many vas 5054 heads !!!

[@LMAutoRepairs]

😋 👍👍👍

[@roxanneabbott8424]

Luis excellent job as always!!

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@jgeorges3061]

LUIS, Thanks for what u do and all the information you sharing with others HAPPY NEW YEAR brother and prospers for 2021 and beyond. cheeeeeeers

[@LMAutoRepairs]

Thanks! Happy new year!

[@craig84downunder]

Nice job, I'll have to lookout for a broken Audi to fix

[@LMAutoRepairs]

😊 Thank you for watching and for your comment!

[@neilmurphy845]

You won't have to look to far I'd say I hate new cars why do that if it's an abs fault why does it turn on to steering light and esp as well

[@LMAutoRepairs]

Because the ESP system needs the ABS working to function properly... 👍👍👍

[@neilmurphy845]

@@LMAutoRepairs a that makes sense

[@gerardgillioz6121]

Very good explanation. 👍

[@LMAutoRepairs]

Thanks! 👍👍👍

[@maksympt1]

very helpful and good explanation, thanks

[@LMAutoRepairs]

☺️ 👍👍👍

[@mrgrumpy5116]

good video, well done with the fix, they should all be that easy. let's hope it's going to be an easy 2021 and a really happy new year

[@LMAutoRepairs]

Agree! Happy new year! 👍👍👍

[@kinggordon7288]

Hi Luis can the ABS cause the transmission not to change all the gears its a vw jetta with a 09g transmission??????

[@OldSkoolNiche]

I had this same issue, luckily only changed the sensor & bearing and all 3 dash lights went off & power steering is back

[@LMAutoRepairs]

That's great! 👍👍👍

[@OldSkoolNiche]

@@LMAutoRepairs Great Video i would be lost without this & mechanics suggested steering rack haha! But because i saw this i insisted its only the abs sensor & possibly abs ring / bearing thank you!

[@LMAutoRepairs]

👍👍👍

[@sharonebbage1189]

I've got all them lights on my golf mk5, it's come as the brake pressure sensor as 1 one of them

[@LMAutoRepairs]

Is pressure sensor external or built in inside the module? 👍👍👍

[@sharonebbage1189]

@@LMAutoRepairs not sure, trying to locate it

[@LMAutoRepairs]

If it is internal to the module, a replacement module/modulator block is probably your best option... I never managed to find those internal sensor for sale... 👍👍👍

[@paulsikora5623]

hi LM great content has usual.take care

[@LMAutoRepairs]

Thanks! 👍👍👍

[@beluxauto5968]

Nicely done as always and the rewind kit that you bought , you can´t afford to not have this .

[@LMAutoRepairs]

😊 👍👍👍

[@james-3778]

I may have missed it but was the cause of the steering angle sender just a lack of basic setting due to the other faults? Probably my favourite videos so watch. I learn so much. Im a service technician and would love to do the stuff you do

[@LMAutoRepairs]

Yes... basic settings... Thank you for watching and for your comment!

[@mirasurmaj583]

Is this problems can case heavier steering wheel ?

[@LMAutoRepairs]

Don't think the ABS sensor causes that... Perhaps you have something else... Have you scanned the car?

[@nemanjadzombic6101]

Thank you for another great video!!!

[@LMAutoRepairs]

Thanks! 👍👍👍

[@shahmnnsn]

After changed the sensor do we need to reset the code or it will go . The speed / abs / parking assistance sensor for a Vw touran

[@LMAutoRepairs]

I would clear the codes... just to make sure... 👍👍👍

[@shahmnnsn]

Thanks 👍

[@shahmnnsn]

@@LMAutoRepairschange both rear abs sensor with parking assist sensor . But parking/ revers sensor doesn’t seem to be working . No fault on dash . Any idea how can I test it . It’s a VW touran . Thanks

[@CP-ip6dq]

Very good job and well explained

[@LMAutoRepairs]

Thanks! 👍👍👍

[@mikael8650]

How did u set up the stereo???

[@edgardodizon6434]

Hello I got a problem with steering assist also tried to erase fault code and after it works again after few days red light and alarm for steering assist come back and lost steering assistant completely hope you can give me advise to fix it. I'm from Philippines with audi a3 2007 1.6 sportsback almost same as in your video.thanks

[@LMAutoRepairs]

What is the code that is coming up? That should give you some direction... 👍👍👍

[@omareid8166]

Thanks my friend Really it is usefull and informative Continue doing this

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@ALADDIN9999]

So all your problems have been solved when you change the two ABS Sensor ? Right ( sorry i'm French my English is not top top , thanks for the help i got the same problem with my A3 )

[@LMAutoRepairs]

Just the rear... Thank you for watching!

[@redeyejedi3095]

Any idea why some of my sensors do not come on/ show on dash? PDF regen no longer came on since a year then I recently checked oil level, to my shock no oil and also no oil warning light. Audi a3 1.6 TDI. Thanks

[@redeyejedi3095]

Warning lights *

[@va7052]

I had a few of these.In my case its always been a bearing problem. Lucky Luis....

[@LMAutoRepairs]

👍👍👍

[@RUBZZZ29]

Don’t know if this will help but my Audi A3 1.6 2011 it had over 16 faults listed, had all the fault light on, speedo meter was stuck on zero and petrol meter was fucked. Turns out it was just a fuse issue!! And the car works fine now. zero faults

[@shifty2755]

What blew the fuse in the first place though? They don't blow by themselves?

[@RUBZZZ29]

@@shifty2755 car wash

[@khancross]

22:40 for calibration will it be enough to start the engine and stand or do I need to drive?

[@khancross]

Did not worked with my 8P, tried many times at different times

[@roblet5047]

Brilliant info in this video, I have got the same lights on my dashboard after an engine change. The scan said abs module was faulty so changed it but still got the lights on. It seems I can only sometimes access the Can Gateway and only sometimes recognises abs and steering assist modules. Do you have any ideas. Thank you.

[@LMAutoRepairs]

Check wiring etc... everything that's been touched during the engine swap.. Could be damaged wires, etc... Thank you for watching!

[@roblet5047]

@@LMAutoRepairs hi thank you for replying, I have checked and double checked cables and fuses but know it is easy to miss, will check again. I am learning with Vcds, will check live readings on sensors incase any have been damaged. Your channel is the best I've seen and I have learned a lot already, a real pleasure to watch. Earned a sub.

[@LMAutoRepairs]

😊 Thanks! Yes, it is easy to miss... Check connections and connectors, pins, etc... 👍👍👍

[@roblet5047]

@@LMAutoRepairs 😁🙏appreciate that, I will get onto it tomo. Thanks again 🙏🙏🏴󠁧󠁢󠁳󠁣󠁴󠁿

[@ranabirgahir462]

Hello have Audi A3 2002 diesel, can you tell me where the injectors are

[@LMAutoRepairs]

Top of the the engine...

[@tedankouil2356]

Hi mate I have an Audi A5 2009 when I turn on the car everything works fine but after some seconds when I’m start driving the speedo goes to zero abs epc esp lights came on and shows me also brake warning contact workshop. If I turn off the car everything goes to normal but after a while is doing the same thing. I was on audi yesterday. They did a Dignostic and they couldn’t find any faults because they told me that my ecu has been upgraded. and when they try to find the faults the computer is crushing and doesn’t show any fault. 1 another guy told that the gateway and the wiring has been changed. I have no idea what the problem is but I have saw many videos of you and u find solutions for everything. If u are in london or near the London can u book me an appointment please 🙏 Thanks

[@LMAutoRepairs]

Hi Scanning the car will be essential... That's the first thing... Can't believe audi can't scan it, unless there is an issue with the module itself... 👍👍👍

[@tedankouil2356]

@@LMAutoRepairs with what module? They told me that the ecu has been upgraded and when they try to scant it the odis doesn’t response. I went to 2 dealers no one could scan it..

[@LMAutoRepairs]

With the ABS/ESP obviously... as it is the one that is reporting the faults... Has been updated? Who updated the module then?

[@tedankouil2356]

@@LMAutoRepairs I don’t know the car has a lot of parts from rs5 brakes callipers wheels I don’t know what they have done to the car I have bought it like this. Is possible to book with you?

[@Cannamaine]

Hi! @lmautorepairs. Love your content! I have a conundrum. I recently picked up an 06 A3 3.2 VR6 DSG. With a brand new oem mech unit. My issue is: on very wet days (after heavy rain) the car will drive fine but then flash PRNDS when coming to a stop light or stop sign, issuing a Traction Control light, ABS light and check engine light. Turn the car off and on again and quickly place it into manual 1 and i am able to get going again. The lights eventually all go away once the weather dries up and i am able to drive perfectly for hundreds of miles. Car has a brand new bosch reman alternator, newer battery, new rear brake switches, the new mech unit and service. Any help would be so appreciated you have no idea! 12 codes total, relating to abs, epc, tcu not communicating with ecu etc. but when dry, no issues!

[@LMAutoRepairs]

I would guess water is getting somewhere where it shouldn't...☺️ 👍👍👍

[@Cannamaine]

@@LMAutoRepairs that seems to be exactly the case, just cant figure out where? I checked the input plug on the transmission intself seems to be free of frayed wires. Getting a code for output shaft speed sensor concerns me though…

[@mikesabin8568]

So you have to have all four wheel speed sensors working in order to calibrate steering angle sensor?

[@LMAutoRepairs]

Yes... As is part of the ESP... Thank you for watching!

[@agentmarky5493]

And more. Yew rate sensor and sqib also tied in.

[@LMAutoRepairs]

Correct! 👍👍👍

[@johnf3278]

Advice...can you tell me if the Chinese honda HDS HIM tool is any good and worth buying. Thanks

[@LMAutoRepairs]

I never used it... I mean, I use HDS, but is with the Autel J2534 box.... If you work a lot with Honda, I would say is worth the investment... Thank you for watching!

[@pirateship69]

Great video well explained but I don't understand why you got negative feedbacks

[@LMAutoRepairs]

You can't never please everyone... Thanks! For watching and for your comment!

[@mdaltaf9325]

Hi bro.my car also has the same problem.shall I change steering angle sensor or only abs sensor .I have a fault code Rear left Speed sensor.hope to hear from you asap.many thanks

[@LMAutoRepairs]

Hi Check that sensor first... If faulty, replace it and go from there... Thank you for watching!

[@ADDAUTOMOBILESERVICES]

👍happy new year

[@LMAutoRepairs]

Thanks! Happy new year!

[@Carlosmartinhox]

Hello friend, I have a polo 9n3 1.2 12v, it happens that when I'm driving at least once a week an abs, steering, airbag warning appears... I turn off the car and everything returns to normal. I detected error P0600. I've seen the fuses, new battery, alternator charging 100%, I don't understand why🙄

[@LMAutoRepairs]

Is that error code on yhe engine ecu? 👍👍👍

[@Carlosmartinhox]

@@LMAutoRepairs Yes is the only error that appears on the p0600 scanner. I turn off the engine, turn it back on and the steering light disappears, they only come back after 2/3 days...

[@LMAutoRepairs]

Any codes on the ABS or on any other modules?

[@Carlosmartinhox]

@@LMAutoRepairs Thanks, I'll check this out better...😅

[@vwaudiservisvaloni9181]

You are Doktor i love your work

[@LMAutoRepairs]

😊 Thank you! 👍👍👍

[@CihangirOTOLastik]

Hi. Is Autel able to calibrate the steering angle sensor? could you do that Can he bring it to the 0 position.

[@LMAutoRepairs]

Yes... it does... Thank you for watching!

[@CihangirOTOLastik]

I am using Autel. The Vw steering angle sensor could not be calibrated to the zero position. Have you ever tried Wv calibration with Autel? thanks.

[@LMAutoRepairs]

Yes... have considered a bad sensor?

[@fahmiali4618]

Where about you based please I have a same problem with my audi a6 thanks

[@EvolveAutoFix]

Which model of Autel you are using bro..?

[@LMAutoRepairs]

Hi MS908P Thank you for watching!

[@tedankouil2356]

Error code 00597 any idea what’s going on?

[@Wandal.7]

I have problem with my esp. 01423 error with G200 sensor... Any ideas ?

[@LMAutoRepairs]

Hi Check wiring... if everything OK try basic settings/calibration... Otherwise replace it... Thank you for watching!

[@Wandal.7]

@@LMAutoRepairs IT a duosensor under seat ?:)

[@autobilisim3240]

My car peugot 508, esp abs lights on when i turn the steering wheel please help me my friend

[@LMAutoRepairs]

Scan the car and go from there... Thank you for watching!

[@autobilisim3240]

@@LMAutoRepairs Is there a place where I can contact you ?

[@LMAutoRepairs]

You just did...👍

[@autobilisim3240]

@@LMAutoRepairs I did

[@autobilisim3240]

@@LMAutoRepairs what can I do now

[@bombaclatskibidi]

hi sir please we need help about bmw transmission

[@mobreyngambi1052]

Nice one bro

[@LMAutoRepairs]

Thanks! 👍👍👍

[@CANDiagnostic]

Top work

[@LMAutoRepairs]

Thanks Mr. Nathaniel! 👍👍👍

[@CANDiagnostic]

@@LMAutoRepairs tse1.mm.bing.net/th?id=OGC.de7349a9e255ae2125054db435cd462b&pid=Api&rurl=https%3a%2f%2fmedia.giphy.com%2fmedia%2fgPHeI6pe9zBHa%2fgiphy.gif&ehk=8aMsnQZ47dQs4k3vCuhxD2Q8hzghzWzcDU%2foV5IAZT4%3d

[@ryanh3285]

My Audi had loads of fault codes because the rear pads needed to.be changed I replaced them and they all went away. I find one issue on an Audi sensor can bring up loads of unrelated fault codes.Not just old Audis either same with my friends 2015 a3.I won't be buying another one.

[@allenschaeffer1675]

Having issue the vw tiguan here

[@emekaonyedire5053]

Your cars are always right hand drive where is your location sir?

[@LMAutoRepairs]

Location...UK Thank you for watching!

[@autovagauto6329]

Muito bom trabalho

[@LMAutoRepairs]

Obrigado! 👍👍👍

[@electronic7979]

👏👏👏

[@LMAutoRepairs]

Thanks! 👍👍👍

[@bg5225]

Thank for the video, I have this Christmas dashboard and fixed one error that was 40% of the magnet ring was gone. However I have the issue of a different wheel showing double speed compared to the rest of my wheels. This makes it so that the abs will not working untill I get this resolved. Have you experience this before?

[@LMAutoRepairs]

No... not that I remember at least... But again, check reluctor ring, and sensor... You swap sensor from left to right to test... if you don't have a scope... 👍👍👍

[@thelastofadyingbreed5890]

My A3 3.2 Quattro has a ESP fault doesn’t scan and Quattro isn’t working on power on the front wheels. Also to mention I just got the rear hub bearing done and it happened a couple weeks after. Anybody body has any advice ? Thank you in advanced

[@LMAutoRepairs]

What you mean it doesn't scan? Without a scan it can be a bit difficult to get any clues... But might worth go through what has been touched during the work done... Just to make sure everything is plugged in etc... Thank you for watching!

[@thelastofadyingbreed5890]

@@LMAutoRepairs I definitely will I’m going to recheck everything when the weather clears up

[@LMAutoRepairs]

👍👍👍

[@paulvw533]

it looks like the front brake pads are fitted with the inside pad on the out side as it has the metal location strips on the outside, these usually fit inside the caliper piston... i assume this is why the brake pad wear indicator is not attached as the wear indicator wire is fitted to the inside pad .. and now the wire will not reach.. total bodge up and the owner should be advised not to try to fix the car as they have no mechanical knowledge and could lead to an accident..

[@LMAutoRepairs]

On this A3, the outer pad also has the metal clips... the clips are fitted on both pads... I never touched the pads, and you are now the second person mentioning that... so I did a bit of research, and quickly fount that information... So, looks like the pads where installed correctly... Thank you for watching!

[@neilmurphy845]

Why would someone do such a hack job a speed sensor isn't expensive and for a few pounds more comes with the brake pads and why does it beep is it because the scanner is communication with ABS module

[@LMAutoRepairs]

Yes... some cars don't do nothing... some just flash the lights... audi also beeps...🤷‍♂️ Thank you for watching!

[@4642mati]

Super 👌

[@LMAutoRepairs]

Thank you! 👍👍👍

[@lawsonthursfield6950]

Great in-depth video Luis as always , I have subscribed to you patreon but can’t seem to access it . Payment is showing gone in the bank . Would appreciate it if you could possibly help

[@LMAutoRepairs]

OK... thanks! Which pledge did you went for?

[@lawsonthursfield6950]

@@LMAutoRepairs £3.00 ( £3.60 with vat )

[@LMAutoRepairs]

Yes... that should give you access to all my posts... Just make sure you logout and log in again...

[@dineshkarki8322]

Sir P0602 and P0610 code on mazda 2004 help me

[@LMAutoRepairs]

Hi What is the background of the car? Those codes are usually referring to programming and coding issues... Thank you for watching!

[@dineshkarki8322]

@@LMAutoRepairs can i reprogramming via ktag/

[@LMAutoRepairs]

Depends on the ecu... if ktag supports it, and you have a good file to do it, yes... 👍

[@dineshkarki8322]

@@LMAutoRepairs thanks for your advice

[@dineshkarki8322]

@@LMAutoRepairs sir can I buy mazda 1.6 bk original ecm file?

[@nazkhan9353]

Can i have your contact need you to work on my audi similar issue

[@TheMis2ryameen]

Hay brother Can you do mine?

[@matushodor4725]

👍

[@LMAutoRepairs]

👍👍👍

[@aymenmohamed1134]

👍🏻👍🏻👍🏻🌷

[@LMAutoRepairs]

😊 👍👍👍

[@ashnyc90]

Please put the seat belt on so that beeping stops

[@LMAutoRepairs]

I will... next time...😋 Thank you for watching!

[@plamenm1641]

Good ol' english rust....

[@LMAutoRepairs]

😊😋 👍👍👍

[@robertdowler8188]

7:20/25:08 pads are in wrong lol

[@LMAutoRepairs]

🤷‍♂️ Dunno... I never had them out... Thank you for watching and for your comment!

[@einfelder8262]

I would have checked the other 2 wheel sensors - chances are the same idiot has done the same thing to them as well. And he'll be back soon for injectors, dragging the last dregs of fuel complete with crap out of the tank :)

[@LMAutoRepairs]

Hope not... nearly 1 year an did not came back... so looks promising...🤞🤣 Thank you for watching and for your comment!

[@macmac9140]

Ban all sensors 😂

[@LMAutoRepairs]

🤣🤣🤣🤣

[@dh1474]

Play at 1.25x speed and thank me later!

[@LMAutoRepairs]

🤣

[@shifty2755]

VAG group cars aren't as good as they once were.

[@LMAutoRepairs]

😊

[@bitwyipodrozesamochodowetv2995]

Ciekawy film. Mój zdechł na akumulatorze a po naładowaniu pokazał błąd Esp. Na taniej diagnostyce nic nie wychodzi. Sprawdzę jeszcze może jakieś wykresy. Co może być?