Complete In-Floor Heat & Boiler Installation!

[@BenjaminSahlstrom]

Hope I was able to help you on your project! If so you should check out the sales acmetools.pxf.io/9gRWRy on Milwaukee, Dewalt, Makita, & more at ACME tools. They're a fantastic family owned company and many times have the very best tool prices out there. By using my affiliate link you're helping me keep making this content for free! If you think I earned a tip (even $5 helps!) you can send that here: www.paypal.com/paypalme/bensahlstrom Also check out one of my favorite tools on Amazon: amzn.to/4cCaqik You guys are awesome. As an affiliate I earn from qualifying purchases.

[@ajcmutech]

I just wanted to say that I am one of the top rated radiant design boiler installers in western Colorado, (not tooting my horn by any means) and this probably the best video I have seen!!! I have been doing boilers for 30 years, been to hundreds of hours of manufacturer schooling, and installed boilers integrated with geothermal, radiant staple up, slab on grade, radiant staple down with gypcrete, and warm board installations. I have done small boilers up to 2 million btu boilers. Very nice Job guys!!! I love Rinnai as a tankless, but use Weil McLain or Lochinvar for my high effeciency and combi boilers, but everyone has their favorites. I have recently become an instructor for a college in Grand Junction, CO., and am using this video to show one of my classes how this works! Its long, but accurate, informative, and interresting. Keep it up guys!!!

[@greaterdesigns1]

This is not meant to be a sales video or an ASMR video. This was absolutely perfect for content and explanations. You do an incredible job not stumbling across your words. Great quality content Ben!

[@BenjaminSahlstrom]

Thank you!

[@muh_mahdy]

😊😊😊😊😊

[@kpulay]

Thanks! I appreciate the pride you take in your work!

[@BenjaminSahlstrom]

Thanks for the tip!

[@rodm5830]

I like the long format because of your ability to communicate without a bunch of needless jibber jabber.

[@petersantamaria9374]

Benjamin, I wanted to thank you for the information you provided with this video. After searching for weeks, I finally concluded this was the path for me. Came over to YT, searched for the solution I envisioned and there it was, clearly outlined by you. Wonderfully done: detailed, documented, and comprehensive. Thank you so much!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@patrickg875]

Probably the best in depth video I have seen yet. You do an incredible job explaining this stuff

[@abbswinston4258]

I have no plans of ever getting this done (I can only wish), but for some reason I find it so satisfying just to watch and in no way am I bored due to the length. Glad I find your page because your prior video I watched was how to wire a new circuit which was exactly what I needed. Thank You for your videos.

[@Okipouros]

as a mechanical engineer, I did 1 installation my self. Ofcourse designed everythign in Solidworks, and had such faith, that even pre-drilled the mounting holes. Everyting fitted great, didnt cut twice anything, and even did some funky 45-degree to to 45 degree turns, instead of 2 90s when I had to go up and right. Every time i see it, I get some satisfaction

[@haroldhughes1261]

MILWAUKEE Just wrapping up my own 3 zone installation; heading to filling the system. Your effort certainly gave me some new insights and I am appreciative. Cheers!

[@Ergmerphany]

I've stumbled across your videos on a number of occasions, and each time they have proven to be just the information I need. Thanks Benjamin!

[@Shifffyy]

Way to go Ben. It makes me happy to see young people passionate about their trade. I hope you’re always able to find that spark

[@jaywmeinen]

Thanks to Josh and your young apprentice, Oly! I can’t believe that I watched the whole 2:55 but I found it fascinating. I really appreciate your workmanship and attention to detail.

[@fooflateka]

Dude. You the man, man. I wish you were in my state. Peace of mind hiring someone who knows what they are doing and with integrity.

[@adamgrey268]

I'm glad this kid knows how to negotiate. Good parenting.

[@jamesderry3573]

MILWAUKEE. Keep up the great work. Prefer the long format . Always very helpful. Thank you Ben.

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@dennisleazott718]

Ben . . . this is the radiant heat installation video I've been waiting for! Thank you and I love the long format. I have a 2 level barn with attached garage that I will be installing RH inot this summer. The detail you provided has filled in spaces left out of the many other videos I've watched and will be a huge help to me. You rock buddy!

[@nieldcreek2098]

Milwaukee… I’m really enjoying the schooling I’m receiving here. I would like to mention (because you asked) that I would prefer 45 minute videos instead, simply because I watch on my phone and it’s hard to adjust the time bar on such a long video, as I stop and advance or rewind to review certain sections. I do enjoy your professionalism, and this video will be quite valuable in the future as I attempt a diy installation in my future home.

[@jeffhorton742]

MILWAUKEE That video was awesome! Great to see that boy getting a head start on earning a decent living one day. I hope his Grandad is around to see you doing great work as well.

[@brendenkelly3861]

As an apprentice, your videos are extremely informative and useful to me, thanks!! Channels like yours make the trades much more accessible to us younger generations and that is ultimately going to help our entire culture because we will have more trade workers!

[@jjleda7324]

I bought a 1961 ranch style home. It had a oil fired boiler with baseboards. I replaced the whole system. I went with a combi boiler and installed radiant floor heat. I used a different style system called ultrafin. It doesn't attach to the floor, but is suspended 2 inches below the subfloor. We absolutely love it. Unlimited hot water, and nice warm floors. And I did it all myself. The only problem that i have, my local building inspector can't approve it. He states that the installation is correct and I did nothing wrong, but homeowners can't install their own boilers. Thankfully, I have no intention of selling. Great video. I did watch it all the way to the end.

[@micheljansen85]

Euro fella here, I have a 160m2 (1780sq ft) living area. UFH and design temp -7,2c. Brick house built post WW2 (1952) when the area i live in was given to Netherlands (German again now). Cavity wall insulation, mostly dual and some triple pane windows. Roof still needs to be done. Heating it with a 12kw air-water heatpump (vaillant arotherm plus) and the whole system pushes the water on just 1 large internal pump that can move 2m3 of water per hour. Indoors temp is 20c (68F). Pinched the supply upstairs on the manifolds as you showed so its alway 15-16c (59f) in the upstairs area. Bathroom is the only solenoid managed area, mornings and evenings its 21, rest of the day its a setback to 18c. My heatpump runs weather compensated so it automaticly adjusts the the supply temp. Once a day, by using a diverter valve, it heats a 300 liter cilinder for domestic hot water which i‘ve put on a circulation pipe that runs 6.30am-9.00am and 5.30pm-7.30pm so near instant hot water at the tap/shower. The thing i love about my system, was the ease of install for a non-plumber like me. The large main runs and technical room i planned in copper (press), the rest in pex(pressfit). Ended up making it all in pex due too the low temps it sees. Max temp for heating is 32c and domestic hot water is 55c And i agree sharkbite‘s only use should be emergencies, and even then copper/steel press is usually just as fast and gives a permanent repair.

[@johnnyseegs]

Channel Locks…always have been, always will be. I really liked the long video/full install format. Someone mentioned that it’s a bit of a pain to scroll chapter on a phone, which it is. But having access to a full install AND be able scroll chapters…pros outweigh the cons. Great content

[@BenjaminSahlstrom]

One way that's easier to "scroll" is to click on the timestamps in the description instead of dragging back and forth.

[@GambleGodOfWar]

As a 1st year HAVC student & apprentice in Canada I have to say that, This right here is Great a refresher. Love your content as it is very helpful, as to others this may be a whole lot of mystic work mumbo jumbo but it is quite simple when you break it down to brass tacks. It truly a pleasure to watch you work and listen to your commentary almost like a podcast/ Yet I find it interesting as some of your Gas and Building Codes are some similar and some are different. Koodos, and you have my subscription for more content

[@jackofalltrades5199]

MILWAUKEE! It’s a pleasure to watch your work and listen to your commentary. The end result is exceptional and you should be very proud of your attention to detail. I’m now retired, but I can tell you without patting myself on the back that you remind me of me in that area. my wife says it’s my German blood. Lol God bless you my friend you’ll go far.

[@nahuiollin13]

MILWAUKEE great video. Took me three days to get through it but it was great. You are a craftsmen!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@guloguloguy]

.....WHOA!!!!!!! AT ~2:30:45, YOU MENTIONED THE "BEND-RADIUS", BUT, THEN MEASURED ACROSS THE "LOOP's DIAMETER", AND CALLED IT " ....~14" BEND RADIUS".... YOU NEED TO DIVIDE THAT "14" IN HALF, TO GET THE ACTUAL "BEND RADIUS"!!!! DO THE MATH!!!...

[@sac2376]

MILWAUKEE - I just completed the same project on my new house. 3 zones, one for the basement floor and 2 in the living areas. I used mixing valves to regulate the temperature of the in each manifold/zone. the living area is standard wood framed with the tubing between the plywood using the same aluminum plates you stapled to the bottom of the floor. For domestic hot water I installed a heat exchanger in the primary heat loop. Using a flow switch I turn on a pump that sends heated water thru the exchanger to heat the domestic hot water.

[@prizedcoffeecup]

So I was just watching this because it came up in my feed from the overnight videos I play for noise while sleeping, and noticed you also have a Fit! Love these little nuggets so dang much, lol

[@BenjaminSahlstrom]

The Fit is AWESOME. Mine is a a manual which is super fun.

[@indeedgrasshopper]

MILWAUKEE Great video. Thanks for making it. Been thinking about adding radiant heat to my downstairs for a long time and this (plus your previous video on the topic) seems to have covered much of what I'll need to know. This is probably the longest KZbin video I've ever watched and I enjoyed it. Can't explore all the nerdy details without taking the time. Thanks again!

[@WORM1100]

MILWAUKEE! This video auto played after one I was watching. I watched the whole frigging thing because it was put together in a way that kept my attention and I just had to keep going. Good job. No leaks was the most impressive part. Huge thumbs up for teaching the kid, he'll be the best help you can find by the time he's 15 years old.

[@ranbymonkeys2384]

What a perfect example of what happens when you take pride in your work. Everybody knows that guy (those guys) that don't give a flip about what they do at the workplace, imagine them doing work like this. Ya right. That looks insanely good, like a work of art. You sound young, I thought that kind of workmanship was long gone.

[@melissalaird2006]

I love the longer format,,,,, I just have to find the time to watch it all..... I also loved the full length video you did on hooking up an electrical panel. I told a friend of mine about it that was building a house with absolutely no experience and when I saw his panel I could tell immediately that he watched your video.

[@lossless4129]

Dude I just can’t express just how much I appreciate your teaching, pace and style

[@AlecTurner]

MILWAUKEE ... broski I learned more from your video than working with a HVAC tech for months. Excellent my brother.

[@RHHE-hj3om]

I'm not a builder nor even close to being a tradesman. Soldier by trade...not used to building but tearing and blowing stuff up. Splendid video, explanation and show & tell. It makes me much more comfortable to have this installed in my next build.

[@ChrisLogan-d1b]

Absolutely fantastic video. I watched the entire thing while working on boiler plans. Thank you for all the detail work and time you spent filming and editing! Thank you!

[@ericmartinson8910]

MILWAUKEE; It was truly awesome to watch the craftsmanship and the thorough explanation of your boiler install What was even more impressive was teaching your son to be proud of his work, people have lost pride and workmanship and it’s truly wonderful to see

[@laurakogen7215]

Amazing video. Thanks so much for posting this content. So useful to be able to see everything from start to finish with all the detail and the list of tools and products.

[@branthebuildor9480]

MILWAUKEE. Great video. I really do like these long format videos much more than a summary. Keep it up!

[@Ymh860]

You went the extra mile! Now this is a tutorial video, i felt like i was the helper on the job 🤣

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@laurijorgenson6683]

MILWAUKEE You’re amazing, my fellow Minnesotan! I learn so much from you and I so appreciate you. Great videos. You are worth a long video. It’s like watching an awesome television program about DIY except better since it’s you. Thank you so much. Your work and content contain so much pride in craftsmanship, not to mention love for your family. Beautiful job, Ben. Quick question- do you have to worry about dissimilar metals and a reaction with copper going into the stainless manifolds? And way to go Josh! Loved what you did.

[@BenjaminSahlstrom]

Thanks for the tip! No, it's not a concern mainly since the heat transfer fluid will reach a neutral PH unlike a potable water system. It's very normal to go from brass, to copper, to black iron, stainless steel, and so on for boilers.

[@banderson5144]

Been watching your channel for a long time and I love watching these long format videos.

[@dennisf.macintyre117]

Milwaukee tools quality seems to me the quality of your work and attitude! I enjoy all three!

[@Plumb-Papa]

Amazing video, love the full in depth walkthrough!

[@georgekolos5255]

My "hat" off to you young man. I'm 30 yrs in HVACR trade so far and could not imagine such job to be done more professionally. I also started off by becoming my dad's "helper" I'm 46 yrs old now and I imagine you followed my path A couple time saving tips if you don't mind. Teflon and pipe dope are totally overkill for such. Relief valves are only 30#s. Stick with pipe dope only/ wipe excess off. Prime PVC vent lines prior to gluing. Here in Chicagoland, inspectors look for the purple primer to be seen on every joint easpecially outlet that has acidic condensate. Way too many failed joints with no primer I have seen. You have more isolation valves on this system than most. No need for extra valves to isolate EX tanks. I have cut and thread black pipe and soldered copper pipe up to 4", silver soldered and braze stuff up to 4" Now I press up to 2" copper whenever I can. Just as good as soldering I believe. Many videos on you tube expieremented pressing with gasket removed. Turns out it not the gasket that makes the primary seal. Think about all them dielectric, flange, etc. Where rubber is seal that almost never start leaking There is real skill involved with doing such easpecially when trying to braze 2" copper to SS. There are no quality sweat fittings of any kind these days :( I use Brdgit solder exclusively. It can bridge small gaps. We call all such tools here Channellocks! We set expansion tank air pressure before installing to intended operating pressure. Never heard if setting 2#s below? Expert tips given on an amazing job! Keep up such work! One day believe me that you will no longer care if you put some pipe wrench scratches on some pipes ;)

[@ranbymonkeys2384]

As for the last comment, I highly doubt it and unfortunately for me, that makes everything else that you typed irrelevant. It's the fact he cares about the little things is what makes what he does, PERFECT!!

[@smalldogbigdong6975]

@@ranbymonkeys2384 easy buddy, your going to disregard everything he said for one thing he said. But all the stuff George Kolos is solid. As your right the little things that are Not overlooked make for quality work. That said Time is money and scratches are a non issue. Like my old foremen would say, Ta-ta-today junior today

[@Nihilumbra]

Титаническая работа 👍, отличная подача материала, техническая и качественная речь. Спасибо Бенджамин 😉 крутой формат 😎🇷🇺

[@mnbeardie]

MILWAUKEE! When I saw the Menard's run, I had to figure out where you are. Good to see a fellow MN tradesman on here. Thanks for a quality walkthrough.

[@tgraham360]

This was a great video! I chose to watch this over something on Netflix even. I put my system in back in 2015 and watching this reminded me of that. I really appreciated your narration and education and also your attention to detail. I also was very deliberate on which direction I was soldering my fittings to make sure the pretty side was out. I've tried to record myself doing projects and it just doesn't go this well so nice work with that as well. Definitely gained a new subscriber here!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@maintenanceman1015]

Great video . Something that helped me later was once I got it running smoothy I wrote settings in the manual where they had the suggested settings I put mine . Had a boiler short cycling to find that when they came in to test the unit they change the target set to 180 when is was to be 160 hence trip high temp. Had air unit heat not working at 67 to find outdoor senor had failed and default was 70. No AC outdoor was 80 senor failed senor default was 60. Great video editor and links listed below.

[@jeff-w]

37:00 I have that exact furnace you mentioned and I had to replace the secondary condenser a few years ago. The unit was about 15yrs old when it failed. It breathes external air. The guy who sold me the parts was surprised it had lasted that long.

[@SHarris64]

Love the long format videos. Great information. Most comprehensive video I’ve seen on a hydronic system. Thanks!! 👍🏻👍🏻

[@chrislarson3123]

What a awesome video! Absolutely great attention to detail, GREAT JOB!

[@bobbijesus8435]

Milwaukee. I Appreciate your time and knowledge. This is motivation for many of us!!

[@mcd5082]

Excellent video Ben! Loved the whole project in one video!

[@georged.sutcliffejr.4489]

Fun job! One comment - I found that placing a ball valve before the expansion tank. This makes replacing the expansion tank very quick and easy. They do "go bad" over time so being able to change it without losing much water is nice.

[@SureRon]

It’s a safety thing to not have a ball valve prior to expansion tank but I agree it would be better.

[@georged.sutcliffejr.4489]

I agree with SureRon that it could be a safety issue sotTo prevent the valve from being turned off accidentally I remove the handle and hang it near.

[@kgsails7102]

@@SureRon The expansion tank isn't a safety device so it can be isolated. Once a system is running, or after it's been turned off for a few hours, the water is no longer expanding or contracting so the expansion tank isn't doing anything.

[@kozmyqmynd]

You are a bad man Ben l thoroughly enjoyed watching you work and l admire your work even more, you absolutely rock!!!. Here l am looking for a video about my mini split ac unit, stumbled across your video and l could not stop watching. It was even more fun watching you teaching your son, which reminded me of my dad I. He he always had me either watching or helping him work and as a result I'm very handy today with DIY projects, saving myself tons of money and feeling very accomplished when I'm finished. Keep up the great work man I'm a huge fan 😃👏👏👏

[@brandonrogers7942]

i will add though i like how you use simplicity with this because that is definitely the way to go good job man great video

[@seancorcoran5172]

Great video Ben! I must remember that "Safety Squint" technique you demonstrated myself 😉

[@ProudRight]

Thanks!

[@BenjaminSahlstrom]

No problem! Thanks for the tip!

[@codyhodkinson8338]

This guy is top notch love his videos! I’ve learned so much idk how he knows it all! Good work sir!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@bluesteel48]

MILWAUKEE. Great content. Very well presented.

[@Greenpointins]

Amazing work attention to detail you’re clearly an an expert and artist!

[@MGPackers]

Can't wait brother! I would not know where to start.

[@eddiereichel9354]

First video I watched of yours.. that's one heck of a boiler system. Your kid is a hoot. Can tell you are a awesome dad

[@nohands3255]

The additional info and long content is great

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@jaywmeinen]

MILWAUKEE You really do nice work. Perhaps the most amazing thing is gluing all that PVC and not having any purple primer showing!! No matter how careful I am, I always manage to have some primer showing. Of course, I’m no professional.

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@slicknick8713]

MILWAUKEE, GO VIKINGS. I'm also a fellow Minnesotan. Great video sir and enjoy ur content. Keep up the good work and Keep living the dream good sir

[@AlecTurner]

BENJAMIN you are an excellent teacher my friend. long-form video for the WIN!

[@eugenkaranxha5053]

Soldering is the most guaranteed way to do pipe constructions you know it will last as long as building stands

[@trevorreece6999]

My Bronco was down, the wife was at work and I was borrowing my moms tt convertible in the middle of winter. I loaded the carseat and went to menards to rebuild the failed cast-iron sink combo water closet drain. Thank god I did not need a long stick.

[@tim8215]

MILWAUKEE tools are great, love that pex crimper you have. We're building a house and Im going todo the radiant system, thanks so much for the detailed video!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@justinweberg4083]

MILWAUKEE! Great video as always! As a fellow Believer in Jesus Christ, I so greatly appreciate your content and Spirit-filled manner in presenting work videos! As a pastor of a small, rural church, I have been greatly assisted by your content on many occasions as I work on our building projects, and serve different folks within our congregation and community. In fact, one of your videos this past summer (full panel replacement) came in answer to prayer as I was helping my father-in-law (a missionary to Mexico) work on replacing his panel here in the States. I wasn't confident with dealing with shared neutrals, and you addressed it and answered my questions as if you were here working with me! While I hope you benefit financially from taking the time to record, edit and post your videos, I want you to know that you have been a blessing to me personally, and to our ministry in New Hampshire! God bless you, Brother!

[@BenjaminSahlstrom]

That's so awesome! I am very thankful for the unique opportunity of being able to help people for a living and pray that I am able to be a witness for Him even on simple things like repairing miscellaneous things. Keep up the good work in New Hampshire!!!

[@sheppardfun5360]

Love this, good work sir! I am chemical engineer, this content is fuel for my soul. If I win the lottery, I’m flying you out to do my house!!!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@Babula134]

Best like always. Thank you for your work

[@melissalaird2006]

MILWAUKEE! Loving all the detail. Finally someone took the time to show me the correct way to solder pipes!

[@ajfreeze215]

This was awesome!! I just paid a KZbinr to design a system for me. If I had found this video first…….Either way, I’m still money ahead. Your video sure makes me feel more comfortable about the plan I have moving forward……..after I get my new gas meter……

[@BenjaminSahlstrom]

Glad I could help!

[@TheMrMauwie]

Very cool video! Maybe interesting to hear from a european perspective: We are moving more towards heat pumps and ultra low temperature heating (25-28 celcius max) using no gas (just electricity), for those applications we go for 16 to 20 mm tubing at a 10cm heart distance (

[@stephanm5493]

Lots and lots of information. Thank you,, you’ve given me the proper confidence in installing my boiler. Cheers 👍

[@BenjaminSahlstrom]

Fantastic!!!

[@dylanwood7810]

Milwaukee, I just started doing industrial hvac, and I'm now more convinced than ever that I want to be a boiler guy

[@dylanwood7810]

Also, personally I wouldn't have put the T on the exhaust, since the exhaust is going down, some of that exhaust is going into the intake, which can dirty up the flame sensor, and cause ignition faults, that condensed gas is acidic.

[@bwlyon]

Wow, now that’s an installation!

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@SpicyLlama_]

I'm a mechanic by trade, but this was a great video to watch. You're like the Rob Dahm of HVAC.

[@exp2023]

It comes standard in Korean homes. It's rare to see such a large area. It's really cool work.

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@RetiredSignDude]

At 32:00, besides the length of the unit's life- consider that all the in-home air that is used for combustion is necessarily replace by air infiltration from the exterior.

[@ComingUpNextTime]

The tip I got out of her, the manifold for the pressure test and removing it with the zip disc to reuse later. I hate building those. Thanks!!

[@wernerberry7800]

Super great video, buddy! Thanks so much for sharing! 👍👌

[@amytaylor1054]

Hello there , how are you doing today?God bless you!!!❤

[@danielgeng2306]

That was an excellent install and tutorial video! Very impressed by the young gentleman (Olie spl?) helping out towards the end!

[@m1geo]

MILWAUKEE - Keen to do something like this in the UK. Currently sitting in my house with clunky radiators and old gas boiler! 😁 Looking out at the snow! 😁

[@jessemull3018]

MILWAUKEE. WOW good video. From a master craftsman and contractor(retired 30 in field) good job

[@BenjaminSahlstrom]

Thanks 👍

[@wpherigo1]

MILWAUKEE - pretty awesome video!

[@monochromatech]

No idea how I found you, and I live in a house where this is totally impossible to recreate.... So why the hell am I watching 2 hours of this? Sweet video man. Love long content that's informative, and makes me feel like I could complete this job when I build my custom house.

[@neadomtucker]

Great work!! I made it to the end! I would love to see a design or set of drawings. Great work BEN!!!

[@codyhamilton7822]

Milwaukee I love the long videos because it's awesome!!!😁😂🤣

[@stevenpringle7813]

Outstanding work and video. Very well done.

[@MannistoCay]

Milwaukee, Ok Ben you sir are a rockstar. We're just about to install an outdoor boiler system to our heating system here at the Cay and I think I may need to go back and redo our local "professionals " work. Excellent info and editing, job well done. Mark from Mannisto Cay.

[@michaelbarbone9310]

Great assistant.

[@michaelbarbone9310]

This was a great video, Ben !

[@inspector8572]

Milwaukee, it’s perfectly normal to get a slight rise in a hydronic system after fire is applied. Even though you have purged all the free air from the system there still is dissolved air in the fluid which will separate or degas over time. Great job and the system looks great. The valve with bleeding port @ the expansion tank is also recommended because those tanks need to be replaced over time as well have to be checked annually for their initial pressure setting. God Bless.

[@morgangrisby8107]

I did a similar thing for running electricity when I was 15. My garage only had 1 3-gang outlet box, and one for the door opener. I had some wire, so I went in the attic , ran my wire, then poked it through the ceiling and got an extension cord repair end (bit more safe then your thingy) and just used it as an outlet.

[@M-Dash]

I love how precise and 'tidy' you choose to work... anything otherwise would have driven me crazy! 😄 Life is in the details! Awesome job! Thank you for sharing with us! 😉

[@varneysr]

MILWAUKEE, great video Ben. Beautiful work!

[@BenjaminSahlstrom]

Awesome! Thank you!