Lithium Batteries for Car Audio? Yinlong LTO Cells LTO66160H 8000 watt capable Battery Bank [4K]

#Yinlong #Lithium #CarAudio
Today we are going to look at putting together a lithium battery bank for car audio purposes. The Yinlong LTO cells have become very popular as they store a LOT of energy and have INSANE discharge rates. Use 6 in series for 12-14 volt systems and add another for up to 18 volts.
In this video I show the components required to set up your LTO bank and talk about cost. These are not cheap, but they save space and weight compared to traditional AGM batteries. They also have an insane charge cycle of up to 30,000 times so they should last for MANY years! See links below for items I purchased for this 80aH bank of LTO (Lithium Titanate) cells I created:
Yinlong 40aH Cells (XS Power Branded): diycentralshop.com/product/40...
Toolmaker Metalworkz custom links (may need to message if they are not on website): toolmakermetalworkz-com.mysho...
6S Battery Balancer: is.gd/ces6sbalancer
Bolt Depot Serrated NUTS! (12mm x 1.75mm): is.gd/yinlongbolts
XS Power IntelliSUPPLY Charger/Power Supply: amzn.to/2YBvbZ2
Variable 10A Power Supply: amzn.to/31178jG
Mazda2284's video on Yinlong LTO Cells: • 13.8v Yinlong LTO 40ah...
Lithium Car Audio Facebook Group: is.gd/lithiumcaraudiofb
Contact for Yinlong Group Buys: / shawn.mayo.984
➡️ Support OSS / Williston Audio Labs for early access to videos: / oldschoolstereo
One Time "Tip" for Video Support: paypal.me/BigDWiz
📒 Show Notes, Video Gear List and Resources 📒
Make sure you are subscribed to my channel so you'll receive notifications when I upload the next exciting video! Thanks for your support and remember to keep it Old School!
Subscribe to Williston Audio Labs / OldSchoolStereo Here: / bigdwiz
⚡ Williston Audio Labs on Social Media:
www.oldschoolstereo.com
www.willistonaudio.com
/ oldschoolstereo
/ oldschoolstereo
--------Cameras and Gear Used To Shoot This Video ------
(Video Gear I Use)
Camera - iPhone Xs Max 512GB - goo.gl/uFHBh8
Samson Go Mic Mobile - amzn.to/2BSAtll
960 LED Panel: amzn.to/2Sxoq3S
Lavaliere Microphone - amzn.to/2Rw5PIw
Sennheiser Wireless Mic - amzn.to/2BSwIfD
This VIDEO was EDITED with LumaFusion on an iPad Pro 12.9:
iPad: amzn.to/2Ancr1W
Software: goo.gl/6yvWss
-------- Test Bench Equipment ------
SMD / D'Amore Engineering Amp Dyno: goo.gl/sJTcf7
XS Power D1400 Batteries - amzn.to/2BPFCKW
XS Power PSC60 Charger - amzn.to/2CHGcfs
Fluke 1000A AC/DC Clamp Meter: amzn.to/2Rw5WDA
Handheld Dyno: amzn.to/2u2EgKV
My Favorite Screwdriver Kit: amzn.to/2x0VzcE
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!

[@hectorortega9131]

U might call your self a Big Dummy sometimes, but you make some of the most educational car audio Videos out there for for sure brotha, let the force and volts be with you..

[@wal]

Just allow me to flub bolt vs nut and Nano vs Newton meter 🤦‍♂️

[@DanBowkley]

@@wal nothing exploded, you're doing aight

[@blackwhip]

I agree. Good shit. I appreciate it! Thank you bro!

[@jasonrapa7298]

Turned out good man, keep up the videos, loving it. 👍🏼👍🏼👊

[@wal]

Thanks for watching and commenting!

[@PoppaTInstall]

Excellent set up for non-charging. I say that's a win for the bank.

[@keving1774]

I love all your videos great job every time 👍🏾

[@BARBELLS-AND-BUDS]

Nice setup Derek, on my wishlist.

[@DiyAllaroundguy]

Nice and clean ! As I was typing my comment you said it! You can get an 80ah bank for about 900 which is damn good I got a friend that spent 3-4 grand on XS lithium 🤦🏽‍♂️ I’m going to share this with him lol

[@JesusSaves86AB]

I figured those XS lithiums were overpriced but damn. AGM for me

[@GTILOUD]

You can build this bank with the xs power 45 which is rebranded yinlong but a 6 bank series is 45ah not 40h same shit Big D has here just 45. Anyways you can get a 12 cell bank of either the 40ah for 900 but the 45ah is 100$ more it's a lil over 1,000$ but that's 12 cell bank 90ah all the bus bars, bolts and balancer from Big Jeff he has both even the 35ah for a lil cheaper. What in the f*** did your friend buy that was 4 bands lol

[@FuckYouTubeCensorship2024]

​​​@@GTILOUD wrong. For one, xs yinlong isnt real yinlong cells. Plus you can get REAL yinlong for $100 less than xs power sells them at sriko batteries or bms batteries websites. Xs power is full of shit, so is d4s lithium, brand x lithium, and limitless. Also 35, 40, and 45ah yinlong cells all have different c ratings. Big Jeff is a ripoff. Do better research.

[@basslife4evr772]

Don't worry BIG D ur still the man in my eyes brotha (✌🏼💪🏼🔈✌🏼💪🏼🔉✌🏼💪🏼🔊)

[@oscarcorazondeleon2316]

Eres el mejor maestro 👨‍🏫 nome pierdo tus videos no saves cuanto te queremos mucho cuídate

[@wal]

Yinlong 40aH Cells (XS Power Branded): diycentralshop.com/product/40ah-lithium-cell/ Toolmaker Metalworkz custom links (may need to message if they are not on website): toolmakermetalworkz-com.myshopify.com/ 6S Battery Balancer: is.gd/ces6sbalancer Bolt Depot Serrated NUTS!! (12mm x 1.75mm): is.gd/yinlongbolts XS Power IntelliSUPPLY Charger/Power Supply: amzn.to/2YBvbZ2 Variable 10A Power Supply: amzn.to/31178jG Multi-Cell Battery Monitor: amzn.to/2YtXWXd Mazda2284's video on Yinlong LTO Cells: kzbin.info/www/bejne/jGioaZuCaLKKja8 Lithium Car Audio Facebook Group: is.gd/lithiumcaraudiofb Contact for Yinlong Group Buys: facebook.com/shawn.mayo.984

[@FATHERSOFBASS]

Can i use these in 2s 4s 8s not only in 6s or 12s

[@wal]

@@FATHERSOFBASS For car audio purposes, 6s for 14-16.5 volt systems. 7s for 18-19 volt systems. I'm not using 12s, I'm using 6s 2p (6 in series, each bank in parallel). I'll have 2 more banks of 6 soon for more powa!

[@FATHERSOFBASS]

@@wal gotcha... So if you odd number it, it jumps voltage???

[@ryry7886]

So is this an 80ah or 480ah? Each cell is 40 so 480 total right?

[@FATHERSOFBASS]

@@ryry7886 80ah... Each six makes 40ah theres 12 so its 80ah

[@kswis]

Lithium is soo cool. Which I could afford it right now, update: I've purchased 72ah of headway, power supply and a bunch of other junk to test and wire them up is here just waiting on the cells. Stoked to stay @ 14.3v when dumping the bass. Thanks for the info. It's all useful fosho

[@MacNifty]

If it's used for powering automobiles themselves and forklifts and other high power machines... for a sound system.. a definite yes.

[@lawrencecoore3569]

Great information for guys like that are newbies

[@justinnelson6552]

It's crazy how far technology has come in just 3 years

[@busdriver1469]

The force is strong in this one😂😂

[@Flozman1982]

Great vid, I had a little chuckle when you flipped the cell over and I said newton-metre at the same time you said "nano-metre".

[@clippingcoils8215]

Been wondering about these lithiums. Your bank looks clean. Great video

[@wal]

Clean like a whistle

[@jasonghering4389]

@Williston Audio Labs. How long are these banks. I'm doing the same thing for my build. So I'm wanting to build a box to sit them in for safety and to look nicer. You have taught me tons of things. Thanks for being so informative

[@SQ_og]

@@walyou still running these?

[@aaronalexander4883]

Thanks for the info good video.👍🏽

[@_ODJ]

NICE! another diy battery build vid on youtube

[@johnpolaski6126]

Happy holidays nice vid ... thumbs up

[@IchoSPL]

Nice video about the lithium cells man, Cant wait to see more tests with them! Just Diz are Nuts not bolts lol

[@psychotikpaisano]

Yoooo. This is smart. I made a "home sound system" from a car audio setup in an mdf enclosure. Oldass Sony single din, 4 speakers, a jl 250/1 and a 12" infinity kappa. 12v comes from a PC psu. And reserve power from a huge lipo pack salvaged from a fried jump starter. The 12v regulated output from the psu will never over charge the lipos but they are in a battery sack just in case.

[@cboyamg]

Fyi nm = newton meter not nano meter

[@wal]

Great catch. Big dummy lives

[@massivehertz3869]

And a 12mm by 1.75 is a standard metric bolt 😉 nothing special.

[@wal]

kzbin.info/www/bejne/qqLHZHuJlNJpibs

[@wal]

@@massivehertz3869 they were $0.95 each at my local hardware store and $0.16/ea at BoltDepot

[@jvsyoutube3298]

@@massivehertz3869 mmyeah, M12 nut

[@murder5000]

Great video. This helped me alot.

[@wal]

😬👍

[@chillcloud9]

Great video! You should do a custom amplifier build series...

[@Van1018s]

Just did 3 of these. 240ah. Replaced all my 7 titan 8 12volt. What a difference. Single 400 amp mechman alt. Ext regulator. Charge at 15.8-15.9. They will hold 15.1-15.3 for a minute with about a 1500amp current draw. So 500amp per bank. After about a minute it starts slowly dropping, but it’s rarely playing for more than 10-20 seconds at that volume. They also recharge fast. Back off the volume they are back at 15.8 very quickly. I could not more highly recommend these. I did 240ah with very nice bars. Each end accepts 10 sky high oversized 2/0. Total cost $3225. $1075 per bank. Great video big D.

[@GTILOUD]

Do you have any links to where you purchased all of your stuff the bus bars the cells the balancer

[@Van1018s]

@@GTILOUD I bought them in premade 80ah banks from CES. Much easier. Looks a lot nicer. Balanced and ready to go when you receive it. On any search engine type in ces 80ah. First thing that pops up.

[@evilinside5984]

@DrMichaelPetty- Im not doubting your experience with the Titan 8, but were they the PWR= power, or RSV= reserve? Also maybe something was not right in your setup, or the New Titan 8 PWR batteries are much better now? Because i just recently seen a test, where only 1- Titan 8 S6 PWR (10Ah @ 75c!) battery was used (only had a 6amp charger hooked up for the test), and it only dropped 1.8volts (16.0v to 14.2v) and powered an amp to 11,400 watts R.M.S. On the Smd amp dyno, with a 1,000 amp draw! The test bigdwiz ran in this video above, with the 2 banks of 40Ah YinLong Lto, (so 80Ah total), dropped from 15.0v to 11.0v with a 500Amp draw= 1/2 the amperage draw, and more than twice the voltage drop! And only made 5800 watts on the dyno.

[@evilinside5984]

@DrMichaelPetty- That 400 amp alt. charging @ 15.8v supplys 6,300 watts all by it self, then each bank of 80ah yinlongs support 6k, so x3 or 240ah= 18k of battery power, and 6,300 from alt. Power, for a total electrical power output, that would support 24k. The Xs power 6S Titan 8 PWR, charging @ 16.6v with a 400 amp alt., would only Require 3 of these tiny batteries ($799 x3= $2,397) to maintain 16v, with a 1500 amp draw.

[@savage6394]

That thing looks sick!

[@wal]

Thanks bro 👌

[@kingtice22]

Would love to see you do a test on a 90ah cmax bank

[@fletchermusician3365]

Thanks for this Video Derek, it was educational for me... those that pick over a word wrong or nit pick lol need to take a chill out pill LOL no body is perfect.. we all make mistakes... which were corrected .. FFS :-)

[@jarlingesandvik9883]

This battery dont burn thats good.

[@midnight873]

You sir are the best

[@WillProwse]

Nice!!!!!

[@wal]

Thanks Will 🤙

[@b1782w]

? For both of you guys...would the lto be superior to lfp FOR CAR AUDIO (read that lto has faster charge/discharge rate)

[@UrAvgBasshead]

I went with JY 45.6 ah’s with 240a, 1 bank of XS power super caps, 2 15’s DC Audio level 5’s, 2 Crescendo 4k’s strapped while driving I don’t see under 14v. But I like these cells. Maybe switching in the future to CES 80 ah. Thanks big Dawg for the video. Excellent job.

[@HardKnocks160s]

Go with the ces 80ah its worth it ihave a 250 ces alt. Nd don't drop below 14.2. Full tilt Then climbs back up to 14.4 On a synergy wfo 5k at half ohm in 110+ degree. Heat when the cars been runnin g for a while im happy with my ces 80ah. Feels good playing full tilt on idle not dropping below 14.2

[@UrAvgBasshead]

Dbuilt Series thanks for letting me know. That’s awesome to hear even in hot weather. In Ohio we’re hitting 90 degree while driving I’m in the 14’s full tilt. It’s when at idle I drop to 12.8 to 12.2. How do you do at idle?

[@HardKnocks160s]

@@UrAvgBasshead at idle im at 14.3 14.2 full tilt. These lto cells are bad ass well worth the money gained more volume i used to only play at volume 56 clean on a pioneer x8800bhs. Now i can play to volume 60 clean had to re set my gains and volt meter when i switched to the ces 80ah. I used to have 2 northstar agm nsb31s in the rear droping to like 13.2 13.4 at idle almost full tilt while driving around 13.8. 14.0. Now im at 14.4 14.5 full tilt driving once im fully warmed up.

[@UrAvgBasshead]

Dbuilt Series what charger do you use and how often do you charge your battery?

[@HardKnocks160s]

@@UrAvgBasshead i haven't recharged this new ces 80ah i just installed it today i have. A Noco 26000 to charge it later on if i need to it should get the job done

[@ToolsOutsideTheBox]

Interesting stuff! I just spent nearly $400 for the group 31 UltraCap instead, after watching EXO’s video on it. I already own the Maxwell ESM and love it. Wish I knew how to convert it for this

[@201231]

Do you like the ultra cap

[@neildeatherage2269]

@@201231 I recently purchased that Ioxus cap opting for B-stock for 200 vs 400 (a couple days just about every vendor reduced regular price of 400 to 300) which only had some scratches and a little chip on the plastic seem. Purely cosmetic and honestly can't believe that cut the price in half. At any rate I am literally obsessed the cap it is unreal. I can't believe they don't seem to be gaining the traction they deserve. Running 2, 1k monoblock amps with factory premium amp (650ish watts) while charging my phone on a AC/DC converter with Heater/AC full tilt, windshield wipers on, and no perceivable voltage drops, lights dimming, and subs hitting so much harder maintaining consistent power with hungry continues trap bass lines. I literally almost want to purchase another one just in case mine gets stolen or breaks for some reason and they sell out (noticed some websites B-stock is getting low). But I figure with a 10 year or whatever it is warranty by the time the thing goes out whatever is available will be better or perhaps smaller which would be welcome. I still might buy another one while I can get one for 200 bucks for a christmas present or something. Father has a diesel truck that needs 2 batteries and a ton of juice to start so while not a basshead like me could use one of these and only 1 battery and not get stuck somewhere like we did the other day. Have a 5k amp on the way thats happy at mid 12 volts (sure you can guess which one that is) and just going to use my current 120 amp alternator (big 4 of course) and one XS AGM battery sitting next to the cap (have new LA battery under the hood, no isolator no issues) with 100% confidence. Just get one but please leave one B-stock left me me haha

[@dimplezztorres6966]

Dude perfectly explained

[@wal]

😬👍

[@jeremyhall9346]

Great video. Excellent video. However I would use nylock nuts and flat washers.

[@floydbeard5073]

Fancy looking big D I love it.

[@wal]

👌😜👍

[@808pathfinder]

when you do a draw test the cells will go back up slowly when in use,It had a big draw from the start so when voltage drop the amps go up .am using Headways but I want this setup now to go with my 1500F 16v, super caps ;)

[@HifiVega]

Very cool!! The custom electric 80ah battery is a steal when you include all the factors you mentioned.

[@m3rk201]

First

[@jorgepizarro3327]

@@m3rk201 try 2nd..😂🤣

[@m3rk201]

Hifi vega is a car audio god not the same lol im the first mortal haha

[@HifiVega]

m3rk201 I’m more like car audio fool lol

[@sterlingslayden5285]

So we are waiting for that classic hot rod to be fully electric when you're done teaching us about battery storage. If you wouldn't mind can you discuss the glass battery?

[@TheTimshady337]

Nice setup. I have some prismatic LTO's 20ah though

[@Jpilgrim30]

You can find 12mm x 1.75 nuts at the auto parts store. A lot of ford trucks and SUVs used open face nuts that size for lug nuts. They even have serrated washers built on to them as well.

[@wal]

They were MUCH cheaper at BoltDepot, even after shipping

[@varqtube]

Awesome vid, Dereck. Question...At the end of the 1st bank and the beginning of the 2nd bank (between cell pairs 3 and 4), it looks to continue to be series'd. If both banks of 6 are in parallel, where is the + to + and - to - relation? Just trying to gain a little knowledge here. EDIT: Never mind, I see what you did. My turn to be a Big Dummy, lol!

[@aprilarenivar5691]

Can you run the stinger isolator runing agm and lithium?

[@otisjwhite]

You should put a slim foam or cardboard between the cells. Just a safety suggestion just incase a cell overheats and bursts because of BMS malfunction from overcharging.

[@Djmambo77]

Hi Big D. So what are your thoughts? are these good for playing music with the engine off for a while?

[@chuckfarley5415]

Ok so. Just to add to the parallel charging info.. You need to be careful when charging in parallel. Each cell needs to match as closely as possible. Not just in capacity but their impedance, IR (internal resistance) needs to be the same as well. If one cell is lazy, the parallel board is averaging the sum so others can take too much. I would cycle all of these probably 3 times then check what each cell accepts in capacity and what the IRs are. If they differ +\- 2%, don’t parallel them. This is much more crucial with other chemistries but still relevant here. Especially going in my vehicle. Anyways... Love your channel Big D... keep that shizz up 👊🏼.

[@mitchellroberts7954]

I agree. We're generally talking about minor tolerances but it can add up and be catastrophic over time. Less of a problem with caps, but lithium fails in a much worse fashion (unless you can somehow manage to seal the vent on the cap and turn it in to the.. you know).

[@CORZER0]

Did you not notice the balancer he used?

[@recon440]

Also, I would like to add that for car audio applications there are effecively no BMS modules that can efficiently sustain the current draws we may see (400A+). As such, nobody really runs the BMS in the car audio world. I would like to see a retest of this battery bank without the BMS.

[@timhoover1416]

I guess as a person who does not know much about batteries, you did not see the gigantic bus bars that you connect to the amp. The BMS he was using did not control the flow of current from the battery, it only maintains the balance of the cells to each other. I work for the sister company to Yinlong that actually licenses them the LTO to make these cells. I'm an engineer, so I know what I'm talking about. There are BMS modules that will run the power through the BMS, don't buy one of those for high power applications like car audio.

[@KuntalGhosh]

No need for bms. Just use a cell balancer.

[@catch22frubert]

@@timhoover1416 There are definitely stand alone BMS units that can handle 500 amps continuous. Daly makes a 500 amp smart BMS that can do 500 amps continuous and I believe well over 1000 amps burst, and the BMS settings are accessible and adjustable. I've seen them for Lifepo4 batteries, but I haven't looked for an LTO BMS yet, but I'm sure they are out there. You are right though, the BMS would be a constant parasitic drain on the cells, and not desirable, even with the extra safety it provides. LTO Cells are already really safe and can take much higher Voltage than most car alternators provide, so I can understand why most people only run an active balancer with a 6s setup of LTO. Battery hookup has a nice little setup of LTO Cells for $200 that would be perfect for automotive duty, but I think I would probably want a 2p6s version of this setup, so at $400 plus balance board and some kind of Case, it's not so cheap anymore. It's probably still worth it though, just because they will outlast the car you put them in, but that's an argument you couldn't win with some people with a different viewpoint.

[@tomasexteriors]

​@@catch22frubertthank you for sharing this was very interesting sir 🤝 can I ask you a question please?

[@BearMeat4Dinner]

Great video. New sub here!

[@darrellw22]

Great video great info.. im thinking about getting some Yinlong lithium but i keep hearing if u drain lithium off all the power they are trash after that and they can't be recharged after all the power has been drained. Dont know how tru that is? 🤷‍♂️ i appreciate u Old school keep them car audio test coming in .👍🏾 oh and can u pls see if u can do a test on the new Taramps MD 12k .5 ohm version thanks. Til next time Im outter heeeeeerrrrrrrr🏃‍♂️🏃‍♂️🏃‍♂️🏃‍♂️🏃‍♂️

[@David_Poole]

Very cool idea. Ive been contemplating lithium for my newest build.

[@riordonmohamed8717]

Love this test. Can you also test the xs power xmax? Just curious because no one has done it yet

[@gettinthrewlife76]

Oh soo nice BigD👈😎👉. ✌️out from Cali 😎

[@wal]

😜👍

[@Exorcism47]

I'll be good with one bank (6 cells) and stock 120A alternator for 2k RMS?

[@BARBELLS-AND-BUDS]

Is this still current as far as what people are using the Ying Long LTO cells? If so, is the price the same? I'm glad you mentioned in the video not to use an AGM with these because I was considering building one and having the AGM under the hood to the small one and have this in the back

[@loudjunkey4206]

Great info on battery’s great video 💪🏽👍🏼👍🏼

[@mikecasey3055]

Thanks for the video! I’ve been looking for a place to buy these yinlong.

[@wal]

Diycentralshop.com also linked in video description and pinned comment 😊

[@mrjbooker4123]

@@wal where can purchase the battery monitor and is it necessary to get a big alternator while using these batteries?

[@kingrpriddick]

Looking forward to the LiFePO4 video, I'm wanting to do a headway build right now if I can find enough room.

[@mkloudsql3285]

Did u ever get the build, howd they work out

[@kingrpriddick]

@@mkloudsql3285 nope, I've stayed lead acid :( maybe one day.

[@TimberTrainer]

I heard the LTO cells are fire safe. It's always a good idea to place batteries in a safe location, but perhaps these don't need a firewall. Not much information on these. Good point about not using these in the same circuit as standard car batteries.

[@ford1546]

do you use stainless nuts? I think it's important. magnetic metal also on the battery. Do you not reduce capacity when you series connect?

[@jaredappleseed7037]

Anthony Jude is the man 👍

[@spider6837]

That's great to see. The bandwagon on yinlongs is ridiculous. It can work with alts. But comparing 40ah to 40ah. I'm glad to know my 80ah spims are doing better than yinlongs

[@workinprogressharris6416]

spider6837 spims?

[@spider6837]

@@workinprogressharris6416 spimhp08 cells

[@74midwestbass74]

YES SIR!!! I NEED SOME lithium!!!

[@wal]

Links in video description

[@mikelincoln2984]

psychiatric treatment?

[@marcusstanford2574]

Full tilt looks like a better deal being in a case for $1099?

[@mattroadfeldt9012]

So really appreciate the video content you put out. Would it be possible to see how long the yinlong LTO will last with multiple back to back use of a 5k-ish load like you showed in the video? Until you get below 13.8v? The listed manufacturer cell average (6 cells 2.3v in series)

[@wal]

I will show more LTO in the future

[@mattroadfeldt9012]

@@wal I look forward to it! I really appreciate the video content you do produce. Especially this one dispite the mistakes. Thank you for the hard work!

[@gervinsbatista5717]

What is the best charger for the house? How many amps do you recommend?

[@georgeowen2083]

Also you can buy some pretty good size lithium batteries from used medical equipment supply places.

[@richardzan4077]

I have been doing tests on these batteries for 2 years. The problem that these batteries after charging up to 2.8V are quickly discharged automatically. In addition, each cells does not charge correctly. So at the moment of electronic calibration you will lose the total battery voltage. So, after a whole day of calibration, you need to recharge them again. I have batteries of the same company as you. I approach these batteries sold by individual Chinese shops are waste (bad somehow) from a large company - Yinlong. To buy good batteries, you need to apply directly to the manufacturer

[@Hotecce1]

Ok. so if you had 4 or more banks, and kept them fully charged using a 300+ amp alternator, would it be more than enough to power a car audio system, compared to having 4 or more lead acid batteries. Im thinking of using these lithium cells to replace the heavy car batteries, to save weight, and more so, space.

[@jake19xx]

Did you ever do a video of the headway cells?

[@deeznutz9998]

Great to see that you used Metakworkz accessories instead of the over-hyped and priced played-out SMD crap.

[@wal]

Toolmaker is here in NC as well

[@Basshead40]

@@wal I used em for my 64ah 38120 battery terminals. They look fantastic.

[@Geerladenlad]

Powah!!

[@blackflworer]

Im new with the lto, so i got my self 45ah yinlong bank. Is it safe to use it with stock 90a alternator ? I manage to charge it up to 14.6. I use 5k amp on it and i never drop under 13.7...13.8. Is it safe for the alternator to charge the bank and not overheat or burn since i heart lithium haves lower resistance ? I use only balancer for the bank, my car is old and haves no bms i think.

[@303nitzubishi4]

So if they rest above 14 volts then I'm guessing you will need a standalone 16 volt alternator to charge them in an automotive application? The oem 14.4-15v isn't going to be high enough potential to push current into these once they are near full charge

[@sHoRtBuSseR]

Buddy is running 2 80ah CES batteries and a 370 amp alt. Charging at 15.3 drops to 15 full tilt and slowly goes down from there. Long demos no problem and charges back very quickly. 2 12k amps at half each

[@wal]

Great feedback. I’m getting 2 more banks

[@sHoRtBuSseR]

@@wal can't wait to see it. I really appreciate you showing the setup.

[@InvictusMedia]

That looks like old school Hifonics connectors on that balance board.

[@Swenser]

Are these cells really explosionless/fireless? Please test and short one out for us.

[@WAT3VATVUSA]

I Have A Question 3 Northstar AGM31 PRO Vs. 1 Northstar SMSAGM480 Which Is Best with JS 390a Alternator ???

[@Lazerchicken69]

so take my agm out from under the hood and run my main power wire to this to start the car and all?

[@bassboyful]

yes you can

[@GuNNeR2SicK]

Whats the best charger for yinlong lto?

[@mattplachter5200]

So how much power did the amp do on the agm bank?

[@macalla1996]

okay well I'm question if you're willing to answer it good Sir 1. Do you connect this the same exact way you would connect a secondary battery? 2. Substituting this for a secondary battery along with a battery isolator with it. 3. Do we connect this the same exact way? Power wire basically 1/0 from the lithium + all the way to the battery isolator + into the front of a battery front main battery + So once we cranked the vehicle over (depending on what you're charging voltage is) Will it put for example 14.8v to both battery and lithium cells. I'm just going to use my vehicle as an example. I have a yellow top optima upfront d-35 I was going to buy a secondary D-35, I'm a fan of Optima batteries pretty-much old School technology. Anyway if not a I was going to buy a nvx 10 farad capacitor instead? I'm pretty much upgrading my sound system. With a CT sounds 1000.1 and a CT sounds 80.4 total amperage draw would be about 140 amps I think? Along with 135 amp alternator, 1/0 big 4 wiring job. I number this that way there is no confusion. I'm probably wording this wrong but I'm sure you probably know what I mean?

[@thecman26]

Wow, that spensive as hell! Let's see if it can supply the juice enough for a Rockford Fosgate Punch 150HD at 1/2 ohm stereo! :O

[@wal]

😝👍

[@magicmikebangin15s64]

Without even breaking a sweat.

[@tankdog03ify]

I think they to be duty cycled a couple times.. they should recover and fight back sum, try that test again with sum charge going into them

[@charlesphillips1642]

Lanzar 250x4 on 100ah c max and played for an hour no drop in voltage on

[@MrZX1409]

Can you give me the dims for that 80ah dual, I would like to add that to my tour pac on my motorcycle plus is there any limitations on mounting orientation I may have to lay on it's side?

[@ze_german2921]

I was told by XS Power that a Balance board was not required for these cells.

[@zacharystevens8527]

If they don’t want to be paired with agm batteries is that for an extra battery or for the main battery too?

[@treveonalexander5452]

Main battery but not under the hood you would do a battery delete and place the yinlong away from heat

[@theodoresignal]

The 6s charger has been sold out for a while. Any other options

[@evronetwork]

Nice idea to replace the car battery, make it more of a car-battery shape and use that for standard car battery, it should last longer, start car faster and be lighter

[@nebraskaninja1984]

Don't want to put that under the hood though.. especially if you live where it gets cold

[@evronetwork]

@@nebraskaninja1984 just put some material to keep it warm, heck nowadays car manufacturers do that for the regular car batteries

[@nebraskaninja1984]

Still won't handle -30 though is the sad part. They make battery waters though.

[@beardedforlife3740]

@@nebraskaninja1984 do you realize how cold -30 is? Most of the lower 48 states rarely ever see -30 if at all

[@nebraskaninja1984]

@@beardedforlife3740 it does where I live there are plenty states it does Still a great battery. Not knocking it. But they make block and battery heaters because of the cold already lol

[@billyjarvis27]

Is there any special way to hook theses up to the alternator? Or is it the same as a standard battery? I’m still learning bout these so don’t rag me to hard lol

[@image91]

Hm. Looking at switching over to these but so far all the claims of 5000w & 4000w per 40ah bank seem to be false. Also seeing that you mention that they are optimal when charged to around 15.6v. Considering I charge at 14.2v , would you recommend these? Looking to run around 10,000w on bass & 5,000w on mids/highs with a 250A alt. Will either be running 120ah lto & a 1260f super cap bank or 160ah lto. Not sure which is better. From your experience, any advice? Thanks & keep up the great work bro.

[@youngprince6731]

How do you add the monitor on the 6s balancer board ? And what is the other two jacks on the balancer board is ?

[@ralph72462]

Hi need help finding someone who sells the hardware like you have on this video on the LTO cells. I love how hearty those bus connections look. Do you sell these items. If you also sell the LTO cells that would interest me also. Any advice would help just bought some of these cells on Amazon to try out but they bring no hardware at all.

[@o.gwolverine8189]

I guess if you need a consistant voltage for for an extended amount of time like an spl comp they would be ideal but for a daily driver tho lasting four times as long there also more than four times expensive than led acid marine set up.

[@beardedforlife3740]

You sure about that?

[@HS786UK93]

That’s was quite disappointing when it came to the amp dyno. You sounded disappointed aswell. Maybe you could charge the bank up and do a dynamic run? Interesting experiment nonetheless. Appreciate the informative videos as always. 👍

[@wal]

I was a bit disappointed honestly, but I’ve also ordered more cells 😝

[@stevemaniaci4750]

Now kidding almost need like 240 ah which is a couple grand. Stuff Isnt cheap. For sure.

[@HS786UK93]

@@stevemaniaci4750 I currently have 160ah in my car with approximately 16k of amps. And get 0.1v drop.

[@FuckYouTubeCensorship2024]

I had 80ah bank handling 9k clamped just fine. Charged at 16v and dropped to 15.8 at full tilt. Switched to plananno now though and more than doubled system wattage.

[@jaiminbhatt2570]

I want to build 48 volt battry pack for my Ebike How many cell i needed ? 18 is enogh ? Also worried to get 48 volt BMS.

[@Dimofon]

420A alternator +200 ah lto 2pc sq q1-3500.1d bridge to 0.8 ohm. 12+kw clipped 15.5v drop to 15.0v 💣

[@neverenoughaudio9887]

With that charger did you charge after assembly or before you assembly

[@MrMrgarry]

Any company supply these to New Zealand?

[@Petar120]

How long can this battery last on average if pushing 1500w apm without being charged by alternator coz i have stock and don't really want to buy new one?

[@MrRey007]

So what happens when you are traveling? will the alternator overcharge lithium batteries if you drive around for long periods of time?

[@beardedforlife3740]

You always have to use a voltage regulator with an alternator. Some come with an internal regulator and some use an external regulator. What the regulator does is help ensure the system stays at a desired voltage without overcharging

[@GrimmReapa]

So we need some one to make a relay that cuts the connection to the agm batteries when not in use.