Fog Lights on with High Beams (All Lights Mod) 2014-2019 Silverado Sierra Tahoe Yukon Suburban

Link to kit: boostautoparts.com/products/6...
Please note, some trucks may have a solid brown wire in pin 10 rather than a brown with white stripe. Always reference off of the pin locations, NOT the wire colors. If you have any questions please contact us.
This wiring kit allows all of the lights to be turned on simultaneously when the high beams are activated on 2014-2018 GM vehicles. The kit is extremely easy to install and takes less than 10 minutes following our installation video. This is known as the all lights mod and the 6 high mod.
After install your lights will function as follows:
Low Beams Only- Only Low Beams will be on
Fog Lights Only- Only Fog Lights will be on
Low Beams & Fogs- Only Low Beams & Fogs will be on
High Beams- Low Beams, Fog Lights, & High Beams will all be on (GM by default normally turns off the fogs when in high beam, but this kit solves that)
Fitment:
2014 Silverado & Sierra 1500
2014 Tahoe & Suburban
2014 Yukon & Yukon XL
2015 2016 2017 2018 Silverado & Sierra 1500/2500HD/3500HD
2019 Silverado & Sierra 2500HD/3500HD
2015 2016 2017 2018 2019 Tahoe & Suburban
2015 2016 2017 2018 2019 Yukon & Yukon XL
Check our KZbin channel or website for videos covering other model years.

[@boostautoparts]

Link to kit: boostautoparts.com/products/6hi?GM%206hi&Comment&KZbin Please note, some trucks may have a solid brown wire in pin 10 rather than a brown with white stripe. Always reference off of the pin locations, NOT the wire colors. If you have any questions please contact us.

[@christophf3527]

Just upgraded my 2018 Tahoe and it was the solid brown but like you said once I went off the location, I was good to go. Apparently the brown with white is the horn and makes the horn honk when you turn the brights on lol , but easy fix after I went off location. Thanks, works great!

[@AllThingsMech]

For everyone complaining about this mod not working or the horn going off, etc - you need to pay closer attention to the video. Do not simply go off of the wire colors, you absolutely have to find the correct pin locations. GM uses several different vendors for their electrical plugs. The body control module and associated connectors could have been made by JST, or TE/Tyco. Doesn't matter what year, make, model, etc your truck is, you could have two identical 2018 Silverados sitting next to each other, same trim package, features, everything...and the wiring harnesses could look completely different depending on which manufacturer's parts were used on the assembly line that day. You need to go by the PIN LOCATIONS, not the color of the wires.

[@boostautoparts]

Correct, always go off of pin location as primary reference!

[@JonathanRodriguez-rg9zj]

I can confirm this just did this on my 2015 chevy Silverado 1500 the wire he mentioned which is brown and white I didn’t have I had it all brown but I went with pin locations and everything worked out!

[@Firewalker688]

This is awesome! I have done a similar mod in the past but it required a relay install, reaching into some tight spaces and cutting your hands to shreds while on my back on the ground. This is crazy easy. I just ordered one! Thank you!

[@RickPoff01]

Great mod and a five minute job. Thanks!

[@boostautoparts]

Glad you got this upgrade installed in 5 minutes! Have a great day.

[@mitchchandler8101]

The wire positions were correct but the brown with white stripe was solid brown on my 2015 Silverado (brown w/white stripe was in a different position). Fog light indicator on instrument panel is not lit with high beams but fog lights are on. Nice job on the video!

[@boostautoparts]

Hey Mitch, Thanks for the feedback. We always recommend going off of the pin locations as primary reference as GM does change the wire colors from time to time. It is normal that the fog light indicator does not light on the dash. Thanks! -The Boost Auto Team

[@wannarunem]

As mentioned down below my 2018 Silverado 2500 the 1st wire was brown with no stripe. Following pin position worked even though with colors were different than the video

[@anthonydevor01]

My colors were different too - first was straight brown and the second was to me violet with a brown/gray stripe following the position he gave

[@tpmac323]

Thank you for this video. I've wanted for years to be able to do this. I just went to the website and ordered one. Now, though, I want to know about the light bar in the grill. LoL That is the next thing I want to do. I have the exact same truck (and grill). I'd like to know how you found to best mount it.

[@Dany_4129]

My wires were just brown on my 2017 Sierra all-terrain but hooked it up this way and works

[@simonbattle468]

Same on my 17 denali

[@user-er2uu2eg2o]

Just ordered, heard good reviews, let’s give this a shot!

[@boostautoparts]

You won't be disappointed !

[@user-er2uu2eg2o]

@@boostautoparts And you was right, Just got New LED Headlights and Fog lights. And it’s Poppin! Luckily on my 2014 Silverado wire color were the same! The Shipping was quick and I’m very satisfied! Will buy again for my next Truck!

[@boostautoparts]

@@user-er2uu2eg2o Awesome, happy to hear it!

[@kylespaid5878]

Does this work the same with the 2019 Colorado ZR2 Bison with the AEV bumper/fog lights?

[@boostautoparts]

Yes it should.

[@michaelherring8852]

I know this is for all 6 but is there a way to use this kit so it would only activate all 4, I.E. low and high lights only? I have a light bar that is wired to my fog light switch and don't want it and the fog lights coming on when I activate high beam switch.

[@boostautoparts]

Hello, Please reach out to our technical support team to check on this. Thanks,

[@hdrolling]

Great video, I should have watched the whole thing the first time! If you connect the circuit the wrong way it turns the highs on with the fogs all the time, ask me how I know.....

[@jakesmith8366]

If you get the wrong wire and turn the high beams on, the horn goes off. Ask me how I know. Lol

[@ajsullivan2559]

@@jakesmith8366 Which wire was the horn?

[@jakesmith8366]

@@ajsullivan2559 I am not sure of the color, but it was the one right above the correct one. It's been a while since I did it, and that's been many beers ago, so my recollection is a little fuzzy.

[@jpimpala]

jake smith hahah. Thats awesome

[@kevin86670]

So if I have my fogs and low beams on then switch to high beam the fogs will just stay on right?

[@boostautoparts]

Yes

[@justinturbo4323]

So after this the low beams and high beams and fog lights will be on at the same time. 2nd question could you just link the 2 wires together with some spare wire?

[@boostautoparts]

Yes they will all be on at the same time. You can't just use a piece of wire - if you did that anytime your fog lights came on your high beams would come on, which is not what you would want when you're using your fog lights in a foggy situation.

[@tommyvillareale6172]

Which of those wires were the day time running light?

[@boostautoparts]

The DRL was not tapped in this video.

[@thisoldmansreviewsandhowto79]

I have a question I have auto high beams on my truck. To have the auto high beam work I have to shut off my driving lights will this kit still work with my truck?

[@boostautoparts]

Yes - your auto high beams will still work and the fog lights will come on with them. You just cannot manually command the fog lights on (no need, this does it automatically)

[@donniegroff23]

I have a 2017 suburban with the automatic high beam feature. Does this mod effect this feature?

[@boostautoparts]

This integrates OK with the feature you're referencing (GM calls it Intellibeam). The only way Intellibeam is deactivated is if you MANUALLY activate the fog lights. If you simple let the Intellibeam auto-activate it with our kit it will work just fine.

[@robertedgemont]

The jumper is working correctly like it should but the fog light indicator light on my temp gauge goes out when the high beams are turned on. The fog lights are still on, but the indicator light goes out. Is this ok? I have a 2017 Silverado LTZ.

[@boostautoparts]

Hello, Yes, it is normal for the dash indicator to go out. The fog lights should stay on as you mentioned, but the dash indicator will go off. Let us know if you have any further questions.

[@robertedgemont]

Thanks

[@turboz28]

On my 2016 Silverado LT with the fogs off they come on when the highs are on. Is this normal? I don't always want both on.

[@boostautoparts]

This kit will have the fog lights on any time the high beams are activated.

[@ajhill3495]

Just installed it, on a 4x4 Z71 Silverado I had to use the solid brown wire( not the one with white stripe) otherwise a service 4x4 system error appeared, also my horn would activate with high beams lol.

[@boostautoparts]

GM unfortunately changes up the wire colors, so we always recommend going off pin location as primary reference as you found out.

[@ericswinty14]

Ran into the same issue thanks for the comment immediately solve the problem

[@krisstanford8598]

Thank you. I searched for the brown with white wire and never found it. Maybe Boost needs to hire you. Their directions were incorrect.

[@iycephoenixx4249]

​@krisstanford8598 They were going of pin location, the colors were simply what their exact vehicle was working with

[@tuleman]

well i just installed mine on my 2018 silverado but the wires were brown and purple no stripes however location of wires were correct works good. now it just needs to get dark

[@adama5419]

I second this one, my 2018 Silverado also had Brown in position 10 and I guess I would call it purple on the other wire. Again watch pin position not wire color ! Works great !

[@HawkeyeThomas]

Read comments first 🤦🏼‍♂️ turns out my horn works great when I flip my brights on 😂😂

[@mondo9.2.5]

@@HawkeyeThomas lmaoo

[@richwr33]

Followed installation perfectly and all works but when I turn on my high beams my horn goes off and it dosent stop sounding until i turn the brights off.

[@boostautoparts]

If you have a 2014-2018 vehicle and your horn is sounding whenever your high beams are activated you are connected to the wrong pin location for pin 10. Some trucks are known to have a solid brown wire instead of a brown wire with white stripe, so confirm your connection is on pin 10.

[@richwr33]

Boost Auto Parts thanks for the response, but if I remove the tclip wont the wire i had clamped it to now be cut?

[@boostautoparts]

@@richwr33 It will not be cut; the insulation will be slightly stripped. You will want to place some electrical tape over it. Feel free to contact our technical support team at [e-mail] for further assistance.

[@Andykruger_]

I should have read this comment lol. Pretty comical result. In my 2017 silverado there is a brown with white "3 pins from the right" vs "3 pins right" very easy to mix up

[@joshuaschaffer8346]

Mine had the solid brown wire. Worked great.

[@christianbonacci]

Will my fogs and headlights come on with auto on with this mod?

[@boostautoparts]

This modification only gets the fog lights to come on with the high beams.

[@brandondimmitt8467]

I just got my order thanks. One question my truck has auto highs. When fogs are on it doesn’t do auto. Will this make fog lights stay on and all auto functions work??

[@boostautoparts]

As long as you don't manually activate the fog lights, your auto-high beams will still work. Further, when your auto high beams activate they will also activate the fog lights with this mod.

[@brandondimmitt8467]

@@boostautoparts ok but they won’t be on with the low beams? Cause dogs only come on when the buttons pushed w low beams was just wondering if the auto would work cause it doesn’t when the fog button is pushed. But I think I got what ur saying.

[@boostautoparts]

@@brandondimmitt8467 They won't come on with low beams. Give us a call at 765-831-2830 with any questions.

[@ronpope1950]

Pay attention to the wire locations, not the color codes. If you don't the horn will blow, I know. Very easy to do if you get the locations correct.

[@boostautoparts]

Yes, wire color may vary so you should always go off of pin location as primary reference.

[@Guillotines_For_Globalists]

Does this kit still allow the fog light button to turn the fog lights off, or is the button rendered useless after performing this mod?

[@boostautoparts]

The button will not change anything when the high beams are on - if the high beams are on the fog lights will always be on (there's no override)

[@Guillotines_For_Globalists]

@@boostautoparts I see. I believe I am confusing the two kits you sell which each connect pin 10 to 2 different wires. The other kit is for aut- fog lights. I assume that keeps the fogs on with the marker lights regardless, correct, but also allows the fog lights to be on with the high beam lights as well?

[@boostautoparts]

@@Guillotines_For_Globalists Please reach out to our team at [e-mail] with this question and your VIN so they can let you know how it will exactly work on your specific vehicle.

[@Guillotines_For_Globalists]

@@boostautoparts Both kits say they are compatible. GM all lights mod (this video) and GM auto fogs mod.

[@pjm8866]

Can I piggyback the fog lights on all the time kit also? 2019 gmc 3500

[@boostautoparts]

Yes

[@taylorcain1693]

What do you do if you tapped the wrong wire? How do I get it off?

[@boostautoparts]

There is a latch on the side of the tap that can be disengaged to remove the tap. Then you can relocate it. Place a piece of electrical tape over the old location of the tap for safety.

[@seanpen95]

Can you still toggle the buttons and switches so that you can have the high beams on and the fog lights off?

[@boostautoparts]

You cannot. After this mod, the fog lights will ALWAYS be on when the high beams are on.

[@seanpen95]

Thank you

[@turboz28]

If you add a switch in line with the jumper you can deactivate the mod.

[@Guillotines_For_Globalists]

@@boostautoparts How in the demonstration is the user having just low beams without fog lights if that is the case?

[@boostautoparts]

@@Guillotines_For_Globalists This mod triggers the fog lights with the high beams, not the low beams.

[@andy956gcc]

Just installed it on my 2015 GMC Sierra.. Followed the video but my horn was going off after I put the high beams on.. Did a bit of a research and for my model it was a solid brown instead of the brown with white wire..

[@thatdeaddude1]

Just installed mine and have the same issue. Gonna change it and see what happens

[@boostautoparts]

@@thatdeaddude1 Given your horn is sounding whenever the high beams are activated, you are connected to the wrong wire for pin 10. Some trucks are known to have a solid brown wire instead of a brown wire with white stripe, so please confirm your connection is on pin 10 (go off of pin location, not wire color). Please relocate your tap to pin 10 and the issue should be resolved.

[@egcoupe1994]

Does this work on a Denali model too ?

[@boostautoparts]

Yes

[@jsison1991]

Does it give any errors or warning lights?

[@boostautoparts]

No

[@SevenFiftyNorth]

Is anyone aware of a mod to turn your fog lights on automatically every time you start up the truck?

[@boostautoparts]

Our auto fogs mod may be what you're looking for. Check out this video: kzbin.info/www/bejne/h36sl3-ZfsR3gKc

[@anthonydevor01]

Wire it to ignition power

[@masonhatten736]

So mine seems to work but the service 4wd light comes on every time I start the truck now

[@boostautoparts]

That certainly isn't typical and is likely just due to unplugging the BCM while the battery is hooked up. Give our support team a call at 765-831-2830 for assistance.

[@MrReesesantiago]

will this work for a 2014 gmc terrain

[@boostautoparts]

It will not unfortunately

[@pr11me_]

do you have one for toyota corolla?

[@boostautoparts]

Unfortunately not at this time.

[@joerivs80]

Have anything for a 2018 Jeep Renegade Trailhawk?

[@boostautoparts]

Not yet, sorry!

[@joerivs80]

Boost Auto Parts any intentions? And if not, is there any other company you’d point me in the direction of?

[@boostautoparts]

@@joerivs80 Not at this time, but it's something we will look into in the future! We are not aware of a company doing these kinds of mods for Jeep Renegades at this time. Sorry!

[@joerivs80]

Boost Auto Parts thank you

[@zackmcdonald563]

Will the fog lights still work with the low beams on ?

[@boostautoparts]

Yes, if manually commanded on. If you want them to work at all times in low beam mode check out our auto fogs mod.

[@epowell01]

@@boostautoparts Can you stack these mods?

[@boostautoparts]

@@epowell01 Yes

[@Viking690]

You guys should be updating your video. For that brown wire if the horn goes off with the high beams.

[@boostautoparts]

If you have a 2014-2018 vehicle and your horn is sounding whenever your high beams are activated you are connected to the wrong pin location for pin 10. Some trucks are known to have a solid brown wire instead of a brown wire with white stripe, so confirm your connection is on pin 10.

[@scottbuchanan9657]

@@boostautoparts howndo you know what pin 10 is?

[@boostautoparts]

@@scottbuchanan9657 The connector is labeled in the corners. If you have any questions reach out to our team at [e-mail]

[@buenasnoches4428]

Will this work with low beams and fogs too? Or just high beams

[@boostautoparts]

Just high beams.

[@user-nc4sr5io6q]

It is normal that when I turn on my high beams the fog lights come on too??

[@boostautoparts]

Yes, that's the intention of this mod.

[@wesleyfowler8363]

17 Sierra it is brown wire and brown wire purple stripe

[@boostautoparts]

Thanks for sharing!

[@ShadyTreeRepair]

Same pin locations but to help yall, on the 2015 chevy silverado its an all brown wire not brown with white stripe. Otherwise your horn will honk when high beams are on 🤣

[@boostautoparts]

Yes, good advice! We always recommend pin location as primary reference. Sounds like the factory ran out of brown with white stripe on the day your truck was built.

[@LSSWAPTHEWORLD710]

Will this work on a 2013

[@boostautoparts]

Yes, but it's a different video. Check it out at the below link. kzbin.info/www/bejne/aHq1kH2gr7trZtE

[@nikostorm4399]

Did not work i did the brown wire w white strip to brown wire w purple stripe, high beams on fog lights off

[@boostautoparts]

Go off of pin location as primary reference as wire colors may vary. If you have issues reach out to [e-mail] and our team will get it resolved ASAP.

[@pepepepepe33]

You said 2018 in the video, what about a 2019 in the old body style? Like in the video

[@boostautoparts]

This will work for 2019 LD 1500's, and all 2019 2500/3500's.

[@bighitstepside]

Why the fuck would you use t taps?!?!?!?

[@gsettlemyre]

Just seen the mod, my question exactly, why?

[@pop5.508]

Hello, can I contact you on Instagram if possible? Because I have a question about how to install fog lights

[@boostautoparts]

Email [e-mail]