5R110W Common Problems.

[@jackmehoff1565]

Thanks for the video Gary I always learn something new when I watch your videos god bless you

[@mrflinstone2553]

@@jackmehoff1565 it feels like a 2nd - 3rd slight hard shift

[@مواطنتعبانوضايج]

Thank you gary for every video you make I'm learning from you

[@GaryFerraro]

Thanks for watching

[@stevohmelike]

Thinking of rebuilding mine when I remove the engine to go over it. I will be referencing your video to make sure I have my complete kit prior to any tear downs. I don’t like start anything and be missing anything, for example the manual valve. I like to have all the ingredients for the sandwich.

[@GaryFerraro]

Sounds good, i do not recommend you open the pump, you need special tools to line it up. If you do decide to work on the trans let me know, there is a certain way it has to be filled, also clean all surfaces(engine block where it meets the bellhousing) and run extra ground wire to the trans

[@mwyson4095]

My trans feels like a faulty solenoid. I'll be driving along and all of a sudden it pops out of gear and pops back in. Very weird. I see that a lot of online stores sell solenoid kits. I was hoping you would talk more about solenoid failure. I reprogramed my trans for towing then I had the reverse delay you discussed.

[@KBS117]

Wow, where are you located? Question. 2003 f350 4x4 lariat 6.0 diesel. Locks up when put in drive. Go to 3rd and it takes off in 3rd and shifts out ok from there. Tow/haul light starts flashing and it will take off in d without locking up. But it still takes off in 3rd. Pcm command to the computer will not show any gear but 3rd, no matter the gear selector position. Max gear allowed however, changes correctly with gear selector lever. I just put a new pcm in, and it's doing the same thing. Pulled the pan, no metal and fluid is clean. Fan however is going nuts, going off and on, once tranny is warm. Reverse works as it should. I get voltage changes on all solenoids except c. It never gets voltage or builds pressure. Also when driving down the hiway and it shifts out of 3rd into the higher gears, the pcm gear command goes blank. When you stop, and it downshift, it will show 3rd again. 1 and 2 is never used, at any time. 2 codes p2703 friction element apply time, p0703 gear ratio incorrect. I think it's getting hot and engaging the fan after driving it 30 or 40 miles. Fluid is still clean. Truck sat 17 years in a storage facility over estate issues. Has 88k original miles. Everything else on the truck works perfectly, no other codes on anything. Truck looks new and was protected from mice..

[@josefranciscohdez3054]

Thankyou Gary for all that knowledge your share with US Definility all those tips Will be helpfull . Thanks again and god bless you and family .👍

[@billk5727]

Thanks for the video! Beside the $500 diode gear set a new case was also needed. Expensive but still cheaper than a new truck.

[@GaryFerraro]

Yes, you are correct. Company we did it for said the same thing

[@courtneyrobinson1799]

Great video, my 09 mazda 5 at. Acts up when going up hill, and no reverse some time, what could be the wrong

[@juanvicentemedina9110]

Thanks for sharing this video. I have one of this transmissions that dont move forward or reverse but I couldn't find nothing bad or damage.

[@307wyomings5]

What ended up being the problem? I'm having that issue now

[@juanvicentemedina9110]

@@307wyomings5 Broken drum. The one that fits on the pump.

[@307wyomings5]

@@juanvicentemedina9110 is it easy to replace? Mine went out while driving up a hill, goes in park but no reverse or drive

[@juanvicentemedina9110]

@@307wyomings5 You will have to drain the fluid and pull the filter out. After that you will have to pull transmission and put it with the pump up to pull the pump out. Be very careful to remove and install the components on the same order. That drum fits on the pump.

[@REPOOCNITSUJ]

Another great video!! We just had one come in the other day with no drive or reverse engagement and a p0756 and a p2701. Thought for sure the coast clutch drum was broken, but when we pulled it out, no damage was found?? Customer installed their own unit, a Ford reman, in December (April now). the trans is mated to a 6.0L Diesel but we noticed the coast clutch drum had "gas" stamped on it. Ever seen that before?

[@GaryFerraro]

I never have, never really looked at the drum. Anything in the pan? Pump and converter look good? Had plenty with the coast drum going bad

[@REPOOCNITSUJ]

@@GaryFerraro nothing in the pan, fluid was clean and full, pump gears were fine, no sticking or worn valves, converter still looks new? I've had a lot with the broken coast clutch drum too. this is a truck another tech in the shop was working on and we were both surprised to see the drum in one piece.

[@ChetSpencer]

Very informative video. I'm getting an intermittent PO741 TCC solinoid performance code. Transmission is working excellent otherwise. Fluid and filters are fresh. My understanding is that the front pump seal could be worn and causing this. Can I change that seal without removing the pump or fugetaboutit and tear the transmission apart. Also could be the TCC control valve in the pump. It's funny how folks worry about their 6.0L when they really need to worry about their 5R110 😂

[@MrDrwpy]

Was this ever answered

[@ChetSpencer]

No unfortunately, been driving it like this for years now 😂

[@streetbiker0000012]

Gary very nice video. It was very informative. You seem very knowledgeable so figure I'd see if you know why my 08 f350 would have fluid pouring out of the front inspection cover (rubber cover). Trans still goes in all gears and drives. Been parked now trying to figure it out. Any help would be appreciated. Thanks

[@GaryFerraro]

Hi Sean, Does this leak all the time or only when hot. Any noise coming from the pump area when the car is running?

[@streetbiker0000012]

@@GaryFerraro thanks for the quick reply. Yes it leaks all the time, cold or hot. Running or parked. There are no unusual noises at all coming from it either. It's a good solid pour as well. I only drove it once after the inital day. That's after I replaced all the solenoids because I had a fault for solenoid A so tired that before deciding weather to drop the whole transmission.

[@GaryFerraro]

Sean, If leaking from the front, have to pull the trans, if no noises coming from the area may be something like a front seal, or maybe the bushing spun, these pumps do have issues, I have a special tool to line up the pump halves, they also say the pump may suffer from bad grounds in the car. A steady leak and no noise almost sounds like something happened to the front seal

[@streetbiker0000012]

@@GaryFerraro Thanks, I have a decent amount of mechanical knowledge but limited to transmissions. I just never really had to tear them apart before. I felt like it was probably a seal from the beginning. Because no noises, everything still shifted and drove fine just kept leaking. No visable damage to the case. Then I thought maybe the torque converter was leaking (seal or damaged) not sure. Guess I'll just have to drop it and see what I see. I appreciate your input though. Wasnt sure if it was a tell tale sign of more significant damage off the bat though. Thanks

[@GaryFerraro]

@@streetbiker0000012 Don't rule out converter, sometimes the studs leak, when you drop the trans down, try to pull converter out quickly(it's heavy though) to try to see where the leak is, also look at the pattern, meaning if it's just running down the bottom may be a seal, if the whole bell housing is wet all around may be converter, not very common for this trans to leak from the front, the transmission lines look ok?, i had a few of those leaking

[@munemrabadi809]

hi, I'm rebuilding my engine on the 2004 Ford 6.0 powerstroke. where are you located and what is the cost to go through the transmission and rebuild it. thanks

[@dangerdavefreestyle]

can you describe this filling procedure a bit more? i have one with 35k original miles and i would very much like to completely drain and refill it with fresh fluid before the mileage gets too high.

[@rmtz59]

Interesting videos. REALLY NEED YOUR HELP. I lost drive and reverse after a mild spin in sand, so I had it towed home and installed a line pressure solenoid AA.. the one where solenoid body has to get removed to remove the harness. When ahead and installed a new filter and temp sensor. Now my shifter is stuck in park and cannot test the trans. I dont know if the shifter problem was there after the tow because I did not try it before installing the parts. Is that because of something I did or something else? and if it still does not move in D or R what would be the problem?

[@GaryFerraro]

You probably didn't hook up the manual valve. No drive or reverse could be a bad pump, blown converter or stuck open pressure reg valve. Before you pulled it apart did you check the fluid level?

[@rmtz59]

@@GaryFerraroThanks for your quick reply, I did not check the fluid. After the tow it sat in Driveway on a incline so would not have read correctly unless I jacked the front up over a foot. I believe I connected everything after installing the line pressure solenoid. I now have to figure out why it wont shift out of park to test it or get it towed to a repair shop.

[@GaryFerraro]

@@rmtz59 Disconnect the cable at the trans(block the wheels and set parking brake) see how the linkage moves at the transmission

[@dirk1689]

Gary have you ever had one that works fine in forward gears but when put in reverse it jerks like it can’t engage then after 10 seconds or so it locks in reverse.

[@keithferger5206]

Any update on this question?

[@raycash4481]

Hey Gary I am having problems with my 5r110w leaking from bellhousing was wondering if you could point me in the right direction plz sir?

[@metalmorfik]

Do you have a video for the 5r110 inline parking brake?

[@GaryFerraro]

I do not

[@metalmorfik]

@@GaryFerraro thanks for replying

[@carlnutter3239]

I have an 08 6.4 with 200K. shifts Quick and hard into reverse and also drive. pressure gauge bounces between 300 and 330 in all positions at idle, PRND321. Also has pressure control Solenoid electrical code and pressure control solenoid a control circuit high code. Thanks.

[@GaryFerraro]

Sounds like you have an electrical problem and the computer is jacking up line pressure

[@ronymorales3527]

New subscriber Question Which kit do you use to rebuild the trans

[@GaryFerraro]

I only use TransTec

[@GaryFerraro]

Thanks for subscribing

[@ronymorales3527]

@@GaryFerraro your welcome By the way Great video

[@keysautorepair6038]

I have one that is locking up when going into 3rd gear has a stuck on number 5 shift solenoid any ideas?

[@GaryFerraro]

could be a cross leak, may not be a solenoid problem, the computer is blaming the solenoid but may not be a solenoid issue, could have internal problem

[@keysautorepair6038]

@@GaryFerraro Broken sprag?

[@GaryFerraro]

@@keysautorepair6038 Is this ok cold?

[@keysautorepair6038]

@@GaryFerraro No matter the temperature it locks the back tires up when shifting into 3d gear.

[@ajman1984]

Can you give the part# for the forward clutch engagement bolt? I have an early 08 model with a transmission that was built in 07, can’t find the clutch engagement bolt anywhere. Thanks

[@GaryFerraro]

The one that screws into the center support

[@ajman1984]

@@GaryFerraro the one that has the clutch orifice.

[@GaryFerraro]

@@ajman1984 I will check my suppliers website to see if they have it, i purchase from Transtar

[@ajman1984]

@@GaryFerraro thank you sir.

[@thomasbrink9256]

I have a question what would make my trans temp gauge quit working when the fluid gets warmed up seems to be consistent

[@GaryFerraro]

The 5R110W has problems with the temp sensor, usually it reads to high and makes the fans come on, what i would do first is install a new temp sensor, can be done by dropping the pan

[@crashtestperformance3596]

Thanks for your video Gary. I recently did a 5R110W trans swap, replaced the front seals, reman convertor, and all was well for awhile. The front seal blew out. What are your thoughts?

[@davidatac9738]

Ol trans swaper

[@alvinomartinez6549]

Good video info, I have a issue on mines. So after it’s been running for a good 20/30 I have a hard shifting when going into Reverse and into Drive mode. I’m also having a delay when going into only in reverse and drive, but all gear shifts 1,2,3,5, and 6 shift perfectly and I have no codes pulling up on the scanner. Can you shed some light into what may be going on? Thanks I’m advance

[@GaryFerraro]

almost sounds like a filter problem or pressure regulator problem

[@alvinomartinez6549]

@@GaryFerraro thank you I will check on those

[@juniormorris3878]

Thinking about putting a Cummins to mine. Is it worth using this transmission or should I upgrade while have it out?

[@champ2koolchamp199]

good day Gary. so I've been using ur video and successfully rebuilt a 5r110 with no forward or reverse. after 30 mile drive I lost line pressure. None in any gear at any rpm. the live data shows line desired pressure at 80 and shows pc solenoid at 49 psi at park idle or 1000 rpms. removed valve body and everything looks ok. there is small amount of debris in he valve body. ran code p0750. any suggestions on key areas

[@GaryFerraro]

ok, does the car move cold and stop moving hot? or bad all the time?

[@mrflinstone2553]

My 04 f250 has that tranny & when i hit the gas to go forward or reverse i feel a thump like if i had a bad engine mount or tranny mount. Could that thump be transmission or torque converter going bad? Transmission shifts good no problem

[@GaryFerraro]

Im assuming the mounts have been checked? is your check engine light on by chance?

[@mrflinstone2553]

@GaryFerraro no check engine light & i had my wife power brake it and dont see anything move, also there's no thump feeling when power braking either, only on take off

[@GaryFerraro]

@@mrflinstone2553 Does it feel like something is shifting?

[@weedies7577]

Taught me a lot Gary. How could I get you to rebuild my torqueshift. Has 140,000 and still going but its slipping/chattering pretty bad in-between 50-60 mph. Any help would be much appreciated. Thank you

[@GaryFerraro]

Are there any codes present?

[@weedies7577]

@@GaryFerraro no sir.

[@weedies7577]

@@GaryFerraro it has been doing it for months . We don't drive it much as long as your not coasting around that speed its acts fine. I use the tow haul and it seems to help some. As the trans warms up it gets a little better too..

[@weedies7577]

@@GaryFerraro could it be anything other than bad clutches. For it to only slip in one gear. It used to haul horses alot on the highway around that speed

[@GaryFerraro]

@@weedies7577 ok, question, when you say slip, does the rpm shoot up or does it feel like a wash board or rough road?

[@jfubele]

Hey Gary, Great Video, Thanks! One stupid question....How does the shift kit lower the high pressure?

[@GaryFerraro]

Does not really lower it, shift kit should fix the problem, the new pressure reg valve has longer lands addressing bore wear and if there is a pressure spike a relief valve is installed behind the pressure valve to handle the spikes should they occur

[@jfubele]

@@GaryFerraro How much would the shift be affected with the kit in the 5R?

[@GaryFerraro]

@@jfubele Shift really should not be affected, the kit just help for high line pressure and case lug blow out, kit should not make it shaft hard or anything like that.

[@kcromwell82]

Hey Gary. What would be the difference in a 6.8v10 5r110 and a 6.0 diesel 5r110? Is it the front pump? I read somewhere the diesel transmission has a larger diameter pump to make up for the lower operating rpm. Any sort of truth to that?

[@GaryFerraro]

Would have to ask my supplier, there are different pumps but i don't think one is specific to a diesel. I will ask my supplier when i speak to him

[@edwardholierhoek1258]

I have this transmission in an excursion and i recently experienced a shudder while towing my camper at about 65 mph Now if you down shift it it stops and then seems to randomly come back. Im guessing its my torque converter lockup solenoid or the torque converter itself can you advise?

[@GaryFerraro]

Probably is your converter, did it feel like a rough road or wash board?

[@jeffrunyan5065]

Completely rebuilt trans no visible problems. Installed back into vehicle, no engagement.

[@GaryFerraro]

Is this the original problem?

[@vitaly509]

Friends experts, please tell me I have an F-350 2006 g automatic transmission 5R110W error P0730 the machine does not go, I will put it in R, the load on the engine is slightly felt and that's it. Tell me where to look for the reason ???

[@armandrobert9309]

I have a question. I put teflon ring in the forward. When I put the car in reverse the transmission is kicking. But not always. What could be the problem ?

[@AgainstAllOddz]

Same thing here

[@alexcorvi2254]

Gary have a 2007 f550 6.0 diesel with the 5r110w the other day I was loaded transmission started to act funny all of a sudden flared up I let off and it stopped. I go to back in my driveway at the end of the day and had an very slight delay into reverse and the best way I could describe it moving was like slowly letting out a clutch pedal on a manual transmission for the first 1/2 and it then bogs the engine and then it’s normal . The following morning I was making a right on red had my foot on the brake pedal and for a split second felt like the truck wanted to keep going. Went to take off and had erratic shifting again. Doesn’t seem to be slipping, fluid has less than 10,000 miles factory mercon sp doesn’t smell burnt, no codes logged, I’m a diesel mechanic on tractor trailer trucks and by no means an expert on automatics but any help would be appreciated before I take it to a transmission shop

[@GaryFerraro]

may have an issue with solenoids, i just did one similar to your issue and did not see to much, i take apart the solenoids and clean them and install a new EPC solenoid, did overhaul as well but did not see much wrong

[@alexcorvi2254]

@@GaryFerraro thank you for the reply!!! I want to agree with you as well because it has no issue pulling a load and it doesn’t act up all the time. I’m gonna have the local transmission shop diagnose it and I’ll end up probably doing the repair.

[@alexcorvi2254]

@@GaryFerraro unfortunately there aren’t many people I trust working on my own vehicles😂

[@GaryFerraro]

@@alexcorvi2254 Let me know what they tell you

[@alexcorvi2254]

@@GaryFerraro I dropped the pan today after work it’s loaded with metal. Unfortunately I’m sure I have multiple solenoids sticking but I’m beyond solenoids. I found my ground cable to the hydraulic power pack for the dump bed hanging completely off it when I rolled under it. at this point without disassembly i believe my pump welded it’s self or at least started to

[@putazorra291]

Hey just wanted to ask something I’m new diesel owner. Got used f350. Does the 6.0 feel like a slip in transmission when you drive it not warmed up? Once warmed up drives excellent?

[@GaryFerraro]

I would think it should not slip when cold

[@munemrabadi809]

My 2004 f250 powerstroke when hauling livestock trailer on take off charters. It's an annoying feeling and afraid of braking braking down on the road. What may be wrong with the transmission? Thanks

[@GaryFerraro]

This is the first year this trans came out, could have an issue with forward clutch or low diode, any delay when shifting into drive range, you checked the fluid level?

[@munemrabadi809]

@@GaryFerraro fluid is fine and shifts fine. It chatters as I accelerate until it reaches approximately 5 miles and it's ok as it shifts. Thanks

[@munemrabadi809]

@@GaryFerraro diode location?

[@rwccwr7149]

Hey Gary quick question I I'm a small transmission shop in Missouri I've got an 07 Ford F250 with the 5 R 110 w this thing's kind of weird drive down the highway 60 65 miles an hour and all of sudden goes into neutral then shift back into gear you pull off the side of the road and it will almost lock the transmission up and squawk the tires put it in third gear with the gear selector it'll drive fine it seems like it may be a diode or something like that what's your thoughts I replace the valve body and also Illinois AIDS it has no no codes in the transmission 4 engine vehicle has 86,000 miles

[@GaryFerraro]

ok, so is this after overhaul? and then when you pull over the trans is locked up when in drive?

[@rwccwr7149]

@@GaryFerraro no sir it is not after overhaul customer bought it this way brought it to me at first I thought it was electronic so we switched the valve body with a reman valve body then know when I pull off the side of the road the transmission locks up or binds squawks rear tires then releases and is fine but still neutrals out on highway speeds if I put it down in manual 3rd it drives fine

[@GaryFerraro]

@@rwccwr7149 ok, so possible problem in 4th and 5th. Sorry for asking so much just trying to think and we are so busy here, i can't think straight

[@joelgonzalez7713]

How about no gear engagement the pump looks good i dont see and striped gears or shafts i know the park neutral sensor showed all the gears in the scanner but as clear codes and shift trans gear ratio codes come on

[@GaryFerraro]

Pressure reg valve ok, did you change the pump?

[@joelgonzalez7713]

@@GaryFerraro the pump looks good no scrarches i need to remove the balves and ck customer heard a pop noise and it neutralized. Ill start assembly snd psi ck ck valves and solonoids its rare i thoufht somthing would.be striped or broken. It might that regulator valve.

[@GaryFerraro]

@@joelgonzalez7713 Coast drum broke at the weld. What year is this?

[@joelgonzalez7713]

@@GaryFerraro thanks ill ck it out 2006

[@GaryFerraro]

@@joelgonzalez7713 Let me know pls

[@treyivey5431]

Mine only goes into one gear. 4th I think.. won’t go into overdrive. Tow/haul light flashes

[@GaryFerraro]

you have codes present, have it scanned and see what codes you have

[@treyivey5431]

Gary Ferraro check engine light not on.. reverse is fine. When shift into drive. It jumps in gear and has one loud boom. I just got quote of 3300 to rebuild

[@GaryFerraro]

@@treyivey5431 Thats about what they go for, what year is yours? do you have a transmission temp gauge on the dash or are your fans running by chance.

[@treyivey5431]

Gary Ferraro 07.. has trans gauge but runs normal temp

[@GaryFerraro]

@@treyivey5431 ok, temp sensor is a common failure. I would say to have it scanned to see if any codes are present. If your stuck in one gear, it may be in failsafe mode

[@johnstroebel6996]

Gary as always love your videos... I have a question about 5R110W code P0772-00 Solenoid E stuck on ... reverse is good only have 1st gear your thoughts? Thanks John

[@GaryFerraro]

What is the year,make model and engine size

[@johnstroebel6996]

@@GaryFerraro Thanks for the reply it's a 2007 Ford E450 v-10 engine 6.8

[@issaalazzabi6087]

gary how are you what causes k1 clutch to be burned after rebuild the car wont go over 60 mph in 6th gear only in 5th its ok i changed vb tcu did a pressure test when the reaches 60 mph in k1 pressure tap its all good sorry i forgot to mention its 09g trans

[@GaryFerraro]

Let me research this to see what i can come up with.

[@issaalazzabi6087]

@@GaryFerraro thanks gary for your time please dont forget me

[@GaryFerraro]

@@issaalazzabi6087 ok, just give me some time, just got home from work, im also a part of transmission brotherhood on facebook, i can throw your problem out there as well

[@issaalazzabi6087]

@@GaryFerraro ok thanks gary i really appreciate it thanks

[@GaryFerraro]

issa alazzabi just tell me again what you did and was this the original problem. Going to put it out on transmission brotherhood.

[@JosePerez-fw1zj]

Thanks yuo Gary

[@GaryFerraro]

Thanks for watching

[@chrise3801]

@@GaryFerraro I have a 09 that's slow to go into reverse but grabs good once goes in,any ideas ? Solenoid?

[@GaryFerraro]

@@chrise3801 What year is the car

[@chrise3801]

@@GaryFerraro it's a 09 superduty f250 4x4 with the 5r110

[@GaryFerraro]

@@chrise3801 Do you mean there is a delay?

[@superiortransmissionpartsi5357]

what do you replace the temp sensor with?

[@GaryFerraro]

The updated one, which is white in color

[@superiortransmissionpartsi5357]

What if it's the valve in the pump that has the brass pellet? We see them stuck too.

[@GaryFerraro]

@@superiortransmissionpartsi5357 Never had that yet, so far only temp sensor but thanks for the tip. I use a lot of your products, good stuff

[@G-TAKLA]

you are number 1

[@GaryFerraro]

Thank you

[@vitaly509]

I forgot to say the solenoids changed 0 result.

[@jeffchism7427]

Where are you located

[@gustavosolis2244]

Gary ,mi ar110 w no hace cambios y tiene alta precion ,400 psi ,

[@GaryFerraro]

Translation

[@ricardoalvarez533]

He said that his transmission doesn’t change gears and it has high pressure 400psi

[@hemi.210]

I have one that is killing the engine in reverse and in forward any ideas

[@GaryFerraro]

could be a stuck valve in the pump, TCC solenoid, converter itself. Storing any codes by chance?

[@hemi.210]

@@GaryFerraro no codes

[@hemi.210]

@@GaryFerraro remain torque converter, pump is used,

[@GaryFerraro]

@@hemi.210 was this original problem?

[@hemi.210]

@@GaryFerraro yes

[@jhughes1829]

I have a question on the 5r110w

[@GaryFerraro]

ok.

[@jhughes1829]

@@GaryFerraro I have a 5r110w. It recently threw a code for solenoid A Was just driving stoped at a light and it felt like it was in neutral changed solenoid fluid and filters. Drove fine for like 10 minutes then there was a thud now it takes like 2,000 RPM to get it to creep forward or backwards. Any help would be appreciated

[@GaryFerraro]

@@jhughes1829 What code did you have?

[@jhughes1829]

@@GaryFerraro P0751 P2700

[@jhughes1829]

@@GaryFerraro You van call me if that better 208 221 6933

[@1993kawasaki]

i watched a few of your trans teardown videos, it would be nice to have some HD footage other than 360p its almost the year 2020!! LOL

[@GaryFerraro]

Yes, sorry about that, i have to get a new computer, when i try to upload in HD, it tells me there is not enough room and try a lower resolution.

[@gregreitan3634]

Don't get me wrong, I like your videos and watch them all but, the shop looks like a Russian prison. What's with the paint peeling off the walls and poor lighting. Maybe your just used to it. I'm sure the customers don't walk through but maybe look at the shop as an outsider and you might have a different view of the shop. I do like your videos and keep up the good work!

[@GaryFerraro]

Thanks for watching lol

[@jw3433]

@@GaryFerraro Meh, I think the shop looks fine!

[@GaryFerraro]

@@jw3433 Thanks, lol

[@billk5727]

@@GaryFerraro That shop is fine! Up until 1985 I worked out of a shop that was built around 1946. Plus a few other old garages that don't even exist anymore.

[@GaryFerraro]

@@billk5727 Thanks bill, Had the office repainted about a year ago, looking now maybe to do the outside of the building, but other than that people tell me that i have a nice shop