BMW N47 / N57 Crankshaft Pulley Replacement

[@bavers1460]

My daughters 1 Series crank pulley completely disintegrated recently, wish I had come across this video, before we had it recovered to an inde, could have saved loads. Thanks George for a well formated video. 👍

[@developer2023]

How much did a replacement cost?

[@seniorbob5541]

Hi. Another good video. My N47 engine, E60/ 5 series crank pulley is all cracked (121.000 miles). I'll get it changed next weekend. Waiting for autodoc to deliver the parts. Corteco crank pulley + Gates belt kit. Removing the crank bolts with impact tool is the best tip. Otherwise you have to buy a special tool which costs £80 or you can ruin your timing chain if you spin the crankshaft the other way. Thank you George. Keep it like that.

[@2Drezik]

Doing the same job tomorrow, pulley totally failed at 270k km. One thing tho, you can get a Gates 'micro-v kit' with the tensioners and belt, wich will save you about 35euros. 👍 Superb video and job, thank you !

[@salimbr2032]

This video helped me alot since I have the exact same car and needed to replace the exact same parts, can't thank you enough

[@GeorgeAusters]

Welcome bro!

[@nathanbrady1763]

Put my 2011 N47 in today for chain replacement at 108000miles and the mechanic sent me pic of the crank pulley cracked all around in a circle basically😂 I remembered in another one of your videos you mentioned the pulley should be changed too on n47s😁

[@LETHALAPOLLOGAMING]

after watching 3 or 4 videos of this Task being done yours has given me the confidence to do the Job im quite handy i only need to see something once to do it normally but being my first time changing the Belt and in my case as far as i know the tensioner i was worried incase i break my car but its getting bad and needs doing probably idler too and now im 99% i can do the Job myself instead of the 140 pound plus parts i was quoted Thanks

[@GeorgeAusters]

Good luck!

[@ozarkdaredevils]

Thank you from the middle of the US ..... I going to get this ordered !

[@HarleyN93]

the e92 n47 access is actually really good tbh

[@edoardopassera]

For pulleys I only use INA components, the crank pulley I use only corteco on BMWs (since they make the oem one and the part number got revised). For belts only continental, never had a problem with these brands.

[@GeorgeAusters]

Yep i've never had a problem with Gates bro!

[@bilbobagins1653]

shop that ive ordered from those parts are just the same manufacturer as u said, the seller suggested me to get ina corteco and continental belt

[@MyJarrus]

I can tell this guy never wants to have a breakdown as he just made his car bulletproof

[@GeorgeAusters]

Hahaha breaking down is no fun!

[@minhajuddin6607]

George Austers my crankshaft pulley broke on saturday😭😭😭😭

[@OH8EFI]

@@minhajuddin6607 Nothing makes your day better than crankshaft pulley flying loose when starting the car to go from work to home

[@GeorgeAusters]

Should have replaced it before it failed👍🏻

[@OH8EFI]

@@GeorgeAusters Yep. Didn't recognize symptoms, just high pitched rawl when revving engine. And that I guessed to be a bearing somewhere. And it actually was a tensioner bearing. But recalling back, I did have exessive engine shake. But not too bad to be honest. Symptoms sneaked up so slowly that I didn't notice it early enough. I just changed all and it was about 20min job. Than you for superb video! Had to do it in the open in field so all tool sizes, torques etc. were nice to have! Straight forward job.

[@joshuaschliebe3407]

Going to be attempting this on the weekend🙌🏽thank you for the video!

[@GeorgeAusters]

Good luck!

[@darrencable7658]

Great video here mate. I’ve just got a 123d and it got a funny vibration but only when I’m sitting at the lights. Goes away as soon as I pull off. Maybe I should be changing all theses parts just for my own peach or mind. Keep up the good work bro.

[@piovo1]

Does it also sound like a dmf going bad?

[@PoppinPortraits]

Beautiful job. More nice tight components added to her!

[@GeorgeAusters]

Cheers mate👍🏻

[@PoppinPortraits]

George Austers got my belt fitted. Literally 5 mins on mine thank Jeez, no tensioner pulley to loosen as it’s spring loaded so only had to slide a pin through a hole to hold it back. Fitted my new awkward coolant flange/pipe and only had to raise the manifold inlet 4 inches to get at the hidden hex screw so left injectors etc connected. Couldn’t believe how clean the ports are inside as only a fine oily layer present with no coke build up at all, I only do long journeys in the main so that could be the reason it’s stayed clean! I wouldn’t have been able to do it without your tutorial vids pal so thanks again!!!!

[@GeorgeAusters]

@@PoppinPortraits Good stuff! As always mate, my pleasure

[@fuegen9339]

Hey George, any tips for doing the 120 degrees without the pulley moving? Thanks

[@choppingboard650]

Nice job. It's just a shame you didn't show in the video how to do the second stage (120°)

[@carpathia808]

Did you lock the flywheel while doing this? Is it necessary?

[@GeorgeAusters]

No I didn’t.. helpful if you have an impact wrench to undo

[@Pecyn82]

I did on my 2016 lci 320d gearbox stop shaking and engine sound smoother

[@Toob41]

Nice one George. You make it look so easy!

[@craiggardner367]

Another great informative video keek up the great content 🤙

[@GeorgeAusters]

Cheers Craig👍🏻

[@kaisslash5970]

you are exceptional, you know everything, how can i become like you? I want to maintain my car myself.

[@GeorgeAusters]

Just takes hands on experience and research my friend!

[@markwhite2156]

Another great video. Definitely a little job added to my list 🙌

[@GeorgeAusters]

Cheers Mark

[@mohdanuarismail4348]

Hi George, Like your videos. 1) why would u tighten the bolt after u have fit the belt? 2) what if i accidently tighten the bolt using an impact?

[@JonniH18]

Love the video’s. Been really helpful on my N47 a bit of preventative maintenance. One question I have bought blanking plates for my EGR will I be fine doing this as I may not be getting my car remapped for another month or two. Or do I do this just before getting my car remapped? Thanks

[@remaptuning1598]

JonniH18 getting car remapped is a must

[@JonniH18]

Remap Tuning I will be getting my car remapped but it was the period inbetween of removing the EGR and then getting my car remapped will probably be a month, is that fine?

[@remaptuning1598]

JonniH18 no it’s not fine your engine light will come on , the egr is electronically controlled remap is a must

[@JonniH18]

Remap Tuning was just asking for the advice as I didn’t know.......

[@ef293]

Hi, Pleas help me. Can you answer me, I don't have an angle wrench, only a torque wrench. How much is 120° on the torque wrench

[@mohamedabderrahmane6089]

Hi, can you make a video to show how to remove the glow plugs on n47 engine without breaking them? thank you. Mohamed ( from France)

[@GeorgeAusters]

Already done my friend👍🏻 kzbin.info/www/bejne/oZyugminm5V0haM

[@johnphipa]

Hi George - when you torqued the crankshaft pulley up, how did you prevent the pulley from rotating - or with the offset bolts does it not rotate when you are doing this?

[@abaidmughal1]

Hi Phil, I just did my today and had the problem of crankshaft rotating when tighting the torque to 120 deg. So used a impact wrench with offset bolt/socket to slowly tighten the bolts by 120 deg. No rotation of crankshaft and made the job so much easier. No locking tools required.

[@bevis71]

If manual - put a car in gear. Not sure if possible on automatic tho :>

[@andreykins]

On an 'after' video engine is almost stand still, no shaking comparing to 'before'. I am thinking this is either because engine was warm, or an old crank pulley was in such a bad condition that it transferred a lot of vibration.

[@bapmic5608]

Good day, Thanks for the Video, i would like to know why they Crank Shaft wobbles when not mounted Could you make a video about the Wobbling of the Crank Shaft.

[@imtheonlyG]

Another Great Video👍. A quick question for you, when the crankshaft pulley starts to rattle around does it need to be replaced straight ASAP or can you continue driving I. E will it become worse or snap.

[@GeorgeAusters]

Try and inspect it to check for cracking, however sometimes it's hard to see the cracking until its ready to tear off

[@TheLoneRanger1992]

Hi mate I have n47 my crankshaft pulley is all cracked should I change all pulleys or just the crank one? Also if not changed straight away due work and time can it wreck other parts of engine?

[@azizladjadj9523]

Thank you verry good job💪🏽👍🏽

[@ricardasr32]

I set up my tool to torque for crank pulley bolts but Im really afraid that bolts will get overtightened and will eat threads away how many chances for this to happen cause even doing by hand it feels like it might become lose lol

[@sergiodriftdrift]

Hi i lost my pulley and drove about 20 minutes and it started to get hot do you think i could have braked something

[@DynodazeHondaTuners]

Awesome

[@GeorgeAusters]

Cheers mate

[@joseluisMartin]

Hi George, to remove the 4 screws, do I need to lock the crankshaft? if yes, how I should do that, Thank you.

[@GeorgeAusters]

You can install a flywheel locking pin to lock the crankshaft👍🏻

[@joseluisMartin]

@@GeorgeAusters Thanks mate

[@dcog2882]

Hello mate same car but when I'm trying to remove the 4 bolts from pulley it's turning the pulley so I can't break the bolts free ?

[@mickrobo6073]

Same problem hear the guy doesn’t explain about how you stop the engine turning trying to release the 4 bolts🤷🏼

[@ryanwhyte795]

How do you get your cars through the mot without egr valve mate I always wanted to do mine but know mine would be found

[@stevelake9333]

Been loving your videos, when you were about to put the new Crankshaft pully in you said something about it been positioned right, is there a certain position it fits back in also on the new belt does it have a certain way it fits , does it have directional arrows or does it not matter ? Oh and out of curiosity how much would you charge to do a timing chain on a 2010 318d e91 with N47 engine 🤣

[@valeriopilla5108]

Nice and clean bay…..

[@GeorgeAusters]

Indeed!

[@BobSmith-or5fs]

The guy that you wish was your neighbor! Thanks man interesting, just need to get the courage to try some of this stuff.

[@joseyamidgomezatehortua5994]

Excelente trabajo

[@TiagoogaiT89]

Hello George, I've installed a "Continental" cranckshaft pully on my E91, and the damm thing squeak all the time. The belt and tensioner are new, so, not from that. My mechanic said that, I have eard and seen others "Continental" pulleys giving problems and came deffective. Do you recommend any other brand who os good like OEM and no history off problems? Thanks for the help, congrats from Portugal🇵🇹

[@GeorgeAusters]

The one I installed in this video, it’s linked in thr description

[@VendocuadrosAutoelectronicaMD]

Great video! All clear! Nicely done! Will do mine in a couple of days 😁 Thanks for info 🙋🏼‍♂️Cheers 🙋🏼‍♂️

[@markcaulfield6449]

Awesome guide George! My E60 N47 520d is an automatic, anyway off locking crank pulley to remove the 4 bolts?

[@GeorgeAusters]

Flywheel locking pin

[@markcaulfield6449]

@@GeorgeAusters thanks buddy, will have a look for this

[@shrivaarpadayachee2908]

When loosening the 4 bolts on the pulley do I need to hold the pulley in place so that the timing doesn't go off? Or is that not true?

[@GeorgeAusters]

Shouldn’t affect the timing but you could turn the crank

[@shrivaarpadayachee2908]

@@GeorgeAusters I'm hesitant to do it myself because I'm not entirely sure how to hold the pulley in place so the crank doesn't turn. 🥲

[@coventrycity7308]

Done mine today, no need to remove fans or undertrays, abit tight but manageable. I used the holding tool so never needed a impact gun. Mine is a 118D 2010 Auto so no locking the engine via putting in gear😒

[@GeorgeAusters]

Glad to hear you got it done!

[@danyelmadalin3914]

Thx for the specs of Nm for 1 series

[@tomcat2512]

Why you didn't change the water pump along with as it has same access in the area?

[@GeorgeAusters]

No need. These water pumps are not a common failure point on these engines, never seen one fail. Very easy to replace if I need to👍🏻

[@johnbeckwith7279]

Hi George - great video - you do make it look easy friend! - how long did that take in total? It seemed like 30-40 mins. I have an E61 2008 LCI with low CO2 and am hearing noises from the AC compressor (Denso 6SBU14C) both the pulley bearing and the clutch when engaged. I have 2 questions; (1) I am assuming yours checked out ok? (2) Do you happen to know where I could obtain a kit to fix up my compressor drive? Thanks in advance, and keep up the fine work, you are clearly very experienced. John.

[@ravivarman5618]

Hi George, I love your videos... simple and straight forward .. I have got a BMW320 ED 2011 , I don't know its an E46 or E90 .. Can you please guide me to change the coolant. I dont know how to drain the coolant from the engine without starting the engine , Also how to get the air out of the engine without starting the engine, Please...

[@marcusscullin4832]

Hi George, Thanks for the video, very well explained and easy follow😊. I am attempting to change the crankshaft pulley on my own 2008 520d but the bolts were rusted in and the pulley turned a little whilst trying to open the 4 bolts... Will this cause timing issues? Thanks, Marcus.

[@GeorgeAusters]

Not recommended to turn the engine backwards

[@marcusscullin4832]

@@GeorgeAusters Thanks George, I'll get the timing checked.

[@antonychadburn1404]

Keep up the good work. Question for you, I had squeal on steering almost immediately so changed belt, tensioner, fluid and bled it and hydraulic power steering pump but it still squeals and makes a knocking sound only heard from the cockpit. Soon as I switch on the A/C the sound has gone. Any advice?

[@General87Lee]

Great video as always George 👍 I used this to refer to when doing my crank pulley at the weekend, very helpful. Does the orientation of the 2 cutouts on the outer rim of the metal centre matter when fitting the new part? After replacing mine I realised they were at a different orientation to the old part and forgot to check before torquing the bolts up. Can't see a reason why it would matter personally, but always best to check I guess

[@GeorgeAusters]

No mate as long as the bolt holes line up👍🏻

[@General87Lee]

@@GeorgeAusters happy days, cheers for the reply mate 👍 Here's to the next job 🍻 front shocks, springs and drop links for me this weekend

[@GeorgeAusters]

Haha have fun, how long did the originals last?

[@General87Lee]

@@GeorgeAusters just over 130k. However, I suspect they're not the originals as its a Alpina D3 Biturbo and should have Bilstein shocks with Eibach springs. But it's currently got (leaky) Sachs M Sport struts on it. Trying to return it to as original as possible, getting there bit by bit!

[@kirwanjohn101]

@@General87Lee I believe the cut out on the crankshaft pulley that you were referring to is for use with a specialist locking tool to lock the crankshaft pulley during removal and more importantly during tightening to the correct torque.

[@TheLoneRanger1992]

Just looked on eBay there’s some for £55 or euro car parts want £285 for a correco one is their really much of a difference in quality

[@GeorgeAusters]

I've linked the one I used, buy that one

[@TheLoneRanger1992]

George Austers ok thanks will do, just wondered how do you know how many nm your tightening can you not just tighten by hand until it feels tight enough?

[@1gazzarobbo]

Hi George how do you lock the crank to take out and tighten the four bolts ?

[@fredevans1779]

Excellent

[@GeorgeAusters]

Thanks

[@mattiericsson5064]

Great Job, good hints,THX😁👍

[@GeorgeAusters]

No problem 👍

[@danielloughney]

Hey George. Great information in your videos. Had my crankshaft pulley replaced about a week ago and now I have noticed oil leaking behind the pulley. Could this have been caused by the new pulley being fitted or is the oil seal known to fail. Just seems coincidental? Cheers

[@OH8EFI]

Did you solve it already? Some people do change the seal behind it at the same time the crank pulley is changed

[@GeorgeAusters]

May have damaged the front main seal

[@UsmanAli-ew9dm]

Can a bad crank pulley cause the timing chain to make a noise I’m sure a floppy pulley can slighting knock of timing?

[@UsmanAli-ew9dm]

So the parts provided in the description will also fit my e90 BMW 320d 2010 184bhp model ?

[@jamessummers4181]

Great video once again. tensioner pulley is as noisy as your was! Am I safe using my impact driver for removing pulley bolts. Just concerned about crankshaft spinning, is it ok to use impact without locking? I’m not sure how I would lock it. Any suggestions very welcome.

[@GeorgeAusters]

Yes you are!

[@jamessummers4181]

Thanks mate. Final question, do you know what the torque specs are on the crank pulley for final torque?

[@sujeet6635]

@@GeorgeAusters will i be able to use impact on a AUTO e60 too without locking it? CHEERS

[@chipped]

Hey George, does a bad/failing crankshaft pulley cause vibration at idle which smooths out at higher engine RPM? My N47 has done 137,000 KM (85,000 miles). I have vibration when idling and it’s silky smooth when I increase engine RPM, doesn’t matter what gear I’m in. I have replaced the engine mounts which improved it a little, we checked the transmission mounts which look good too. If you have any other suggestions I would really appreciate hearing them. Thanks, Keep up the great content 😃👍

[@GeorgeAusters]

Very possibly yes

[@chipped]

@@GeorgeAusters Great, thanks for the info. Didn’t know about this issue beforehand.

[@абонирайтесезаЛилианачкова]

Hi George I want to ask you my car is not charging the battery what could it bebmv e87 118d

[@1gazzarobbo]

i have a really bad noise from that area dont know if its the tensioner or the crankshaft pulley shall just change both

[@cristianhudrea9223]

Hello, from where do you know how much torque to put unto bolts and nuts when using the torque wrench? I, for one, can't find such details. Thanks in advance!

[@yamahar6london]

Nice video m8 😎

[@GeorgeAusters]

Cheers m8

[@bevis71]

4:33 Yes... 118d/E87 if you don't have Chinese hands - remove fan. 1x screw on the side/top of fan assembly (driver side in UK), 1x electrical plug to unplug right on the top (you cannot miss it), then on the passenger side there's a clip/latch holding fan to radiator just about half way between top and bottom - just hold it with one finger then pull fan assembly UP - difficulty level 0. Oh.... and to do that all you have to take out air filter box as it's blocking access to the screw... 2x10mm socket for the box and 1x flat screw to release the pipe. Total time spend for disassembly airbox+fan+crankshaft pulley - 30minutes. Replacement should come tomorrow so still not sure how long reassembly will take! PEACE

[@bevis71]

Update: Reasembly - same +/- 30min ;). Only difficulty is putting a belt back on when you're alone. Gearbox on neutral + belt on all wheels apart from alternator - easiest to access as on the top - tensioner FULL clockwise then wigle the belt on the alternator pulley - yes it's tight but twist pulley left/right on repeat and it will pop back where it was.

[@bevis71]

Update 2: Wednesday - crankshaft pulley melterd, Sunday - starter motor gone xD. BMW

[@4432andy]

Hi does it make a difference if you torque your crankshaft pulley before you put the belt on? Or does the belt need to be on before it’s torqued up?

[@GeorgeAusters]

Doesn't matter

[@arturzajac8291]

Hi , where i can find the the numeric of fasteners bolts should do ?like what power to use on dynamometer please ,any tabels for show ......idle , tensioner pulley,and crank shaft in n57,530d f11bmw if you don't mind share this info

[@kuzerman]

Does the original pulley have any marks about what brand is it? Because I've heard Corteco delivers this part to BMW factory. In russian owners forum many people discuss this issue and say that no matter what substitute you use (Corteco, FEBI, Gates etc) it goes 50000km +/-, nothing compared to original BMW pulley

[@GeorgeAusters]

The original crankshaft pulley is BMW

[@karatist79]

corteco is the same as bmw. you can see that bmw logo was removed from it. so its the same part. as yes- russian forums are great.

[@davidlong4678]

Wish I saw this before, I fitted Corteco and it failed again in 12 months

[@mohammedsaleem3070]

Very good

[@Milchenx3]

hello, my 120d e82 from 2012 has a servo oil reservoir. What do I have to pay attention to when buying?

[@salam7376]

Hi George, one of my fuel injectors on my, e60 lci 520d 2008, has gone. Do I need to get the exact same make and exact same part no. , to replace it please ? And Can I replace just that one bad fuel injector, or do I need to change all four of them ? Also the part no. I've found from realoem is, Part 13537797877 , which fits other models too. Could you please let me know your thoughts. Many thanks.

[@justboyjustboy2681]

Do i have to lock crank or not before removing pulley?

[@GeorgeAusters]

No you don’t

[@eb4753]

​@@GeorgeAusters thank you for your reply. So if the pulley spins a bit while trying to remove it its not an issue? Or better to use impact gun?

[@miissyb5890]

Hi George, great informative vid as always! 👍🏻 just wanted to ask ... the drive belt u linked 6DPK1817 is for cars 'with air con without electric PAS' ... so ur bmw doesn't have PAS? Just wanted to double check as my E82 has air con n PAS so i think I'd need a different belt? Thanks

[@GeorgeAusters]

Mine has hydraulic power steering, with a power steering pump👍🏻

[@miissyb5890]

@@GeorgeAusters thanks for getting back to me 😊 how can u tell if u have electric or hydraulic PAS? I'm not too sure what I have now lol

[@GeorgeAusters]

No problem, real easy - check to see if you have a power steering reservoir like me👍🏻

[@jaimeberrocal8288]

Hey, George. Is gates better than Febi Bilstein? thanks and good video, mate.

[@GeorgeAusters]

Both similar quality

[@car_guy]

Mine just snapped, i have to order for the crank pully which can take 2 weeks, is there a 1 first aid so that i can get this thing moving am stuck upcountry

[@GeorgeAusters]

No you need to replace the pulley BEFORE it fails like in this video👍🏻

[@definatemsojila4405]

Fresh ✔️

[@timjenkins3971]

Hi there mine seems to have a different tensioner to the one on the video and also has a torx head bolt holding it on

[@QuattroBajeena]

Lol watching video. I was like "i dont fancy removing the bumper and radiator" had a look once air box from the kidney grill is removed space is there :)

[@octaviomachado3643]

Hi there, I'm about to begin this endeavor on my e91 2009 225.000km n47 (it still has the original pulleys and belt😲). How did you managed to lock the crankshaft? Thanks. BTW nice video.

[@GeorgeAusters]

I didn't lock the crankshaft but there is a slot on the timing cover where you place a locking tool into the flywheel

[@octaviomachado3643]

@@GeorgeAusters, can it be done by simple puting the gear box on 6th gear and the e-brake on? Thanks for your help! I did saw that tool in the timming chain replacement video part1. ;)

[@GeorgeAusters]

@@octaviomachado3643 In theory yes. Give it a go!

[@boxinggloves87]

Hi George. Well done job mate. Im going to replace turbo to my f31 318d. I just cannot find the torque manual for the screws :/ do u know where I can find it please???

[@GeorgeAusters]

ISTA

[@simo8295]

Hi Dear George, Thanks for your interesting video. Could you please give me link or document where to find nm tightening torque (nm)? Thanks to you very much. Regards Simo

[@abaidmughal1]

I got the torque settings for my E90 320d from ISTA+. Search for Vibration Damper in ISTA+. On my N47 engine it was 40 Nm torque followed by further 120 deg bold tighting. This can be done easly with a offset angle socket and impact wrench.

[@simo8295]

@@abaidmughal1 thank you very much

[@problemslayer3538]

Hello George. These videos are class. Im actually looking at a 318D Touring M sport on a 2011 plate. 72k on the clock. Is it worth getting the newer model 2013 onwards or are these worth taking a chance on? Was the 2.0 diesel unit changed for 2013? Ive heard bmw addressed the timing chain problem in a certain year but cant get any concrete evidence. Any guidance would be appreciated.

[@8Bits486dx]

Good job 👌👌👌👍👍👍

[@mrme1133]

Hi george, great channel wondering if you can help me with diagnosing a whining noise. When i remove the belt the noise goes away, so deffo pulley related, i have changed the alternator but noise is still there. Rest of the pulleys are smooth. The noise i can best describe is like when you have an electric interferince with a radio, but mines in the belt area. What do recommend to check of replace. My car also has the electric rack

[@mrme1133]

Update: It was the alternator on its way out

[@GeorgeAusters]

Glad you got it sorted!

[@mrme1133]

@@GeorgeAusters yes all done a while ago now moved on to m57 e90 love watching ur vids. All the best for 2022

[@lukeuk7212]

My belt through itself off on start up the other day, didn't realise until 7 miles after getting home, looked inside and crankshaft pulley is at an angle, will my engine be ok?

[@GeorgeAusters]

Pulley probably needs replacing

[@lukeuk7212]

@George Austers yeah it's strange because I was thinking about having it replaced a month or so ago, then this happens lol, the crankshaft pulley is definitely at fault , do you know if it would of potentially done any damage to engine or crankshaft? Thanks for the reply

[@mickrobo6073]

You don’t explain how you stop the pulley from turning round when you’re turning the four bolts on undoing them. ? I’m trying to do the four bolts and the pulley just keeps turning the engine thank you.

[@GeorgeAusters]

An impact wrench is your best friend👍🏻

[@mickrobo6073]

@@GeorgeAusters I managed it mate. managed to lodge thin wide end Spanner a between that two cut outs and I found a a could undo them when it was at its most top dead centre with the compression ..all done now ..thank you …good video by the way well explained👌🏼

[@nastastic]

Hey George, I tried to use a long Allen Key to lock the tensioner in place but I doesn't seem to grab anything in the hole when I stick it in. Did you have this issue? I can't get the belt on as it's too tight. Do you have any other suggestions or tips?

[@GeorgeAusters]

No need to lock it in place, just use a breaker bar

[@nastastic]

@@GeorgeAusters I tried that today but I found it very hard to get it in at an angle to push the tensioner. I was on my own so I'll try with the help of my nephew

[@GeorgeAusters]

Parts and Tools used in this video! Crankshaft Pulley: amzn.to/2PBG1bt Gates Drive Belt: amzn.to/389rtq3 Gates Tensioner: amzn.to/2wRdnfY Gates Guide Pulley: amzn.to/2vtbA0f Small Impact Wrench: amzn.to/2T4igdi Big Impact Wrench: amzn.to/39NOrEu Sealey Impact Socket Set: amzn.to/3a8zcpQ Torx Socket Set: amzn.to/32EbnDV Female Torx Socket Set: amzn.to/2PzAZMQ Torque Wrench: amzn.to/2VF0YpI

[@sujeet6635]

Hi george, is it a same procedure for auto? Or Do i need to lock flywheel to tighten the bolts, i just got myself an impact wrench cheers

[@abaidmughal1]

Use the torque wrench to tighten the bolts to 40 torque, then put a offset angle socket with impact wrench to slowly further tighter the bolts by 120 degrees. Many thanks George for your video, really helped my replace the pulley on my car today.

[@simo8295]

Dear George, How to block the crankshaft pulley to avoid to turn when unscrew or tight the 4 bolts? I have also automatic gear box. thanks for your reply Regards

[@Blakezc]

I want to know

[@linli1698]

I think you need to buy a crankshaft pulley locking tool to lock it.

[@simo8295]

@@linli1698 hi 👋🏼 thanks for your message. Have you a link where to buy this tool ? Thanks 🙏

[@linli1698]

@@simo8295 This is for the tool to rotate the pulley www.ebay.co.uk/itm/383753505505 And this is the tool to lock the pulley www.ebay.co.uk/itm/CRANKSHAFT-CRANK-TOOL-FOR-BMW-N47-N57-LATE-MINI-ENGINES-11-7-220-OEM-EQUIV/361637412115 I bought them, but neither has arrived yet. Here is a video to give an idea on how they are used kzbin.info/www/bejne/e3eUkKmYd9WLiZI One thing to note: DO NOT ROTATE THE PULLEY COUNTER CLOCKWISE!!!!. It may damage your timing system.

[@simo8295]

@@linli1698 thank you 🙏

[@madara7859]

Did you lock your flywheel?

[@mata1133]

How did you lock the CS pulley not to turn when tightening to 80-90nm?

[@GeorgeAusters]

Having the belt on and holding it with my hand was enough👍🏻

[@damiangrabowski2104]

I had Gates after 30,000 km had micro cracks. Now I have Contitech already over 50,000 and like new

[@GeorgeAusters]

I've always used gates and never had a problem

[@damiangrabowski2104]

@@GeorgeAustersI used Gates at Audi and there was no problem either. And here in bmw something like this occurred, maybe it was just flawed ... ps. good job as always Bro

[@GeorgeAusters]

@@damiangrabowski2104 Thanks mate

[@jameslyford]

Hello mate nice vid! Should you lube up the crankshaft pulley seal with a bit of oil or dry with a soft rag? Cheers bud

[@GeorgeAusters]

Yes you should lube it up to help it go on👍🏻

[@jameslyford]

@@GeorgeAusters cheers mate I cleaned the seal and area. Then smeared on oil on the rubber seal. When on easy. I hope it doesnt leak lol

[@simo8295]

Dear George, Would you please advise me the reference of your impact driver (dewalt) and also about the adapter 1/2’´! Thanks very much!

[@GeorgeAusters]

This is the impact wrench I use: amzn.to/2T4igdi

[@simo8295]

George Austers thank you 🙏

[@German_engines]

Hi George, got all my parts to do exactly this job but can't undo the crank pulley as it's moving when I try to undo it, any help appreciated pal on how I can stop it rotate??

[@GeorgeAusters]

Either an impact wrench or crankshaft pulley locking tool

[@German_engines]

@@GeorgeAusters thanks mate, any impact recommendation? Cheers

[@vidoobasenaratne4001]

Good one, thank you buddy.

[@GeorgeAusters]

No problem👍🏻

[@jiyanad82]

Did you lock the flywheel in order to loosen the damper pully? You don't show that. Pully bolts cannot be loosen without locking the flywheel.

[@GeorgeAusters]

They can be loosened with an impact wrench