How I : Bluetooth OBD2 my Honda ADV 150

[@Sparks5]

Very relaxing watching this video!

[@JackButlerVideos]

Fantastic guide! You should know that the "waterproof hot glue method doesn't stay water proof forever as the hotglue and sleeve move with temprature. But it will be very water resistant! You just need to make sure water cannot run down the cables and the pcb is higher. Do you know if you can read the live MPG from this engine? Thanks for the video!

[@mlxnrzhr]

Thanks for the tip.. the live mpg is already bullt into the bike dash from the factory..

[@SkyBlue-fj5qc]

neat. nice content

[@chinkuan1430]

nice one bro. did you purchase the connector at Sim Lim? or online?

[@fafannegara8657]

Apakah jalur data sama untuk yamaha juga?

[@flickerphaskal7652]

nice👍 planning to install one

[@AlfonseTheReal]

Hi, Is this working with 2016 Honda Spacy Alpha SCR1105WH scooter motorcyle. DLC has 4pin. So I think to use this with 4pin to 16pin converting cable. Thank you in advance.

[@francescoesposito9765]

Ciao ti volevo chiedere se può andar bene su un Honda Integra? Se si quanto mi costerebbe farlo fare da te? Grazie

[@baye_vlog]

Nice

[@ahmadnorhelmi5522]

Hi boss, is the obd scanner compatible with uma racing ecu? Cause i cant seem to connect through bluetooth for torque or realdash app): It says ‘checking PID support’ then ‘unable to connect’. But the pairing through settings is all ok alrdy. Whats the issue?

[@nickpeh1066]

Does this work with cb150r exmotion?

[@prasanconstruction]

Wave 125i ?

[@drewmanlongat3619]

Puwidi po ba siya sa Honda beat sir?

[@Kyruu28]

Is it safe for the battery to continuously plug in the elm module? Or do I only plug it when needed?

[@mlxnrzhr]

Been using it for quite sometime. No issue.

[@Kyruu28]

@@mlxnrzhr Thanks a lot for the answer

[@TheFentem]

Hi boss, if i do the cnnection like this, and i use an obd app that can dyno, can i still be able to carry out the dyno function in the app?

[@mlxnrzhr]

Yes

[@TheFentem]

@@mlxnrzhr 👍ty boss

[@gtinero5698]

Hallo, I tried with Honda nc750x 2015 but it doesn't work, it can't find the communication protocol. Can you give me some help? Thank you

[@mlxnrzhr]

Doesnt work with nc750x. It uses the old protocol.

@@mlxnrzhr What about NC750X from 21-23? Does it still use the old protocol?

[@renzydelacruz5579]

Is the wiring same with other brand obd2?

[@mlxnrzhr]

Yes

[@weijielim2062]

Hi can i know which version did u buy? The 1.5v or the 2.1v? Thanks

[@mlxnrzhr]

Im using v2.1.. all v2.1 from china are actually v1.5.. which doesnt work well with the bike.. im still waiting for the brand vgate to reach my place.. which claims to support v2.1..

[@weijielim2062]

@@mlxnrzhr ooh no wonder I got the 1.5v can't read the ecu. I try it on my tracer and adv also both ecu not reading.. thanks for the fast reply!

[@mlxnrzhr]

The v1.5 should still be able to read the adv 150 ecu.. just need to select the ISO1430-4 KWP fast init protocol

[@mlxnrzhr]

Just that the pid request wont be so instant.. meaning there will be a huge delay in the torque app..

[@weijielim2062]

@@mlxnrzhr I will give it a try again later. Will get the v2.1 also to try it on the tracer.

[@mr.younger1086]

Is it okay to leave the obd2 scanner always connected to the adv?

[@mlxnrzhr]

Left it in the bike for over 2 years. No issue.

[@mr.younger1086]

@@mlxnrzhr thanks for the fast reply. You always use your phone connected to the ocbd while on the road?

[@mlxnrzhr]

From time to time i will use it for datalogging. Data i use to tune the cvt and ecu.

[@mr.younger1086]

@@mlxnrzhr thanks sir!

[@samiertv2023]

done scribe san ka nakabili idol ng connector?

[@masterofmachines67]

Can i delete the fault code with this ? I have cbr650r.

[@mlxnrzhr]

Yes you can but im not sure if cbr650 is compatible..

[@LuckyImposter]

this is very complicated to first timer had a motorcycle like me 😅😅😅

[@mlxnrzhr]

Just get this a.aliexpress.com/_mr2ZYKv

[@XinhTruc-ww2yb]

Cách này hiện nay không được

[@jajgaming7007]

Hi, is this applicable to honda vario 150 2018?

[@mlxnrzhr]

I dont have vario in my country, but theres a chance it should work for 2018 and above..

[@jajgaming7007]

@@mlxnrzhr thank you for the info. Hope to see more videos on your channel.

[@MbahPeople]

@@jajgaming7007 Yes it does. I already test it on Honda Vario 125 2018 , and it Works perfect.

[@kushhatkar]

Which app?

[@mlxnrzhr]

Torque pro..

[@-0-__-0-]

I keep on experiencing problems related to Obd2 reader connected but cannot connect to ecu, how can I fix this? Does anyone have any kind of solution?

[@mlxnrzhr]

Try changing the protocol to automatic and let the obd detects the protocol or you could manually use iso14230 fast init for this bike

[@-0-__-0-]

@mlxnrzhr What about for other bikes? The same thing happens to my Yamaha xsr 155. Thanks for the reply ma man 🙏

[@mlxnrzhr]

@@-0-__-0- im not sure what protocol the xsr is using, but you can try automatic detection. If none works the obd adapter isnt compatible with the bike.

[@-0-__-0-]

@@mlxnrzhr Thank you 🤜🤛

[@choonsengniu7267]

Hi can I directly buy from you🤣

[@muhdhafiz3670]

this method cannot be use for honda rs 150