How to Install a Bison Hard Flipback Tonneau Cover | Step-by-Step Installation Guide

[@efrenramirez387]

Very informative and helpful instructional video. Thanks for sharing.

[@ToolboxTipz]

@@efrenramirez387 thanks for watching. Glad it helped

[@briancontant]

Fantastic install video. Retired old guy here appreciates the help. Very clear and concise!

[@ToolboxTipz]

@@briancontant Glad it could help! Thanks for watching

[@stephenadam6716]

Very well done and thank you.

[@ToolboxTipz]

@@stephenadam6716 thanks for watching!

[@dodgeman36tw]

Fantastic install video. Thanks so much for posting.

[@ToolboxTipz]

Thanks! Glad it could help

[@Broxty]

Great video brother, just ordered one.

[@ToolboxTipz]

@@Broxty thanks for watching!

[@mikeboersma4607]

Thank you just ordered one and no instructions in the boxes you made my install go great thanks again

[@ToolboxTipz]

@@mikeboersma4607 glad it could help! Thanks for watching

[@YannickLajoie]

Thank you sir, it was very helpful.

[@ToolboxTipz]

@@YannickLajoie glad I could help, thanks for watching

[@phillipcraggs6202]

I don't know who the original is, but this looks exactly like my RealTruck TriFold. Good video thou. Thanks for sharing.

[@ToolboxTipz]

@@phillipcraggs6202 I’m not sure, I know a couple other companies also have similar styles. Thanks for watching!

[@happyrecluse2849]

Installed same cover on my 3500 Ram about a week ago a decided to come here to see if I missed any thang... Doesn't look like it and no screws left over... Since it is only really clamped down up near the bulk head you might consider checking for tightness on the 2 star knobs occasionally as the cover could shift from side to side with not much locking down tailgate end. I watched other videos on Bison where they had 2 hold down clamps installed, assuming for this purpose . Guessing I bought older stock as it didn't come with the lights for under the cover in my kit. It's going to be more functional than the cap I took off. Delivery was like 3 days... Will check back for your review after a winter in Ontario..

[@tylerrudnicki2346]

Any thoughts on the cover so far? Looking to order one myself and the BakFlip MX4 was my other option

[@ToolboxTipz]

@@tylerrudnicki2346 big price difference, so far it’s been good. Few small issues but nothing major so far

[@CCitis]

Note to everyone here, double check your bed size and what your ordered size is. Don’t ask how I know

[@AlbertPinette]

Just got mine and put on last night. Have 4 hard corner piece looking part left that aren’t on the parts list that don’t seem to fit anyplace.

[@ToolboxTipz]

They may be the end clip for the rails that go up against the box & tail gate

[@AlbertPinette]

@@ToolboxTipz thanks I’ll look again I did try them there and didn’t seem to fit but It was getting late out when was finishing up

[@julieking6172]

We’re also trying to figure out how to install these pieces. they seem important for keeping water out of the tailgate corners.

[@ToolboxTipz]

@@julieking6172 they should be the end for each rail.

[@user-iu5wu5km7u]

It appears that the cover rails only has a gutter drain at one end (Cab end) sort of means that the truck has to be parked facing down to drain after a road trip. My present truck has drain tubes at both ends. Is it possible to order rails with a drain tube at both ends?

[@ToolboxTipz]

@@user-iu5wu5km7u yeah, it only had 2 drains. I’m unsure if they make a set with double rail drains 👎

[@rickvalvo6125]

Drill holes in the rail then run rubber tubing out through the tie down access cover. ​@ToolboxTipz

[@jacksonhamel5987]

Mine just came in but only the cover itself. Called them and they said they deliver the rails and hardware the following day. Anyone else have this?

[@ToolboxTipz]

@@jacksonhamel5987 yeah mine also came in 2 different packages. But both of mine came at the same time

[@CCitis]

Sucks you can’t do this in the wet, which means I have to wait until spring here in the Pacific Northwest! Too much tape and stick ons

[@ToolboxTipz]

If you get a dry day you can do it. Just use a heat gun go warm the top of the bed/ seal

[@hatchbuilds4863]

I believe the locknut goes to the black nut knob thingy otherwise thanks for the video. Having a nightmare trying to get my rails from this stupid company. Not sure why they wouldn't ship with the cover 🤷‍♂️. Recieved the cover 2 weeks ago but no rails or hardware. But looking forward to putting on my new truck when they show up

[@rossrobertson674]

1:43 I got those 3 foam bumbers too but I thought they were just extra in case part of the strip at the back window came loose and maybe u could replace that area, mine cover others I've seen also came with a long strip of square foam about 2"×2" with adhesive on one side, in the videos I watched they cut that into pieces to protect the back window of the truck, seems like u didn't get that

[@ToolboxTipz]

@@rossrobertson674 yeah, I had 2 large foam strips for the box. 3 small foam pieces that go on the flip to protect the window.