Thanks Brian for a great DIY video. This gave me the the location and tips on the best way to change the CKPS on my 2005 ML350.
@SouloftheTroll2 ай бұрын
By far the best video on KZbin about this job! Thanks so much! Clear, concise, and to the point!
@HowtoAutomotive2 ай бұрын
@@SouloftheTroll thank you!
@Koya_Sipanlog_Express Жыл бұрын
replaced mine successfully. I hope no more traffic stop or intersection stalling. Thank you!
@dannyninerempire7 жыл бұрын
I was about to spend $200+ I'm going to do it myself and spend only $55 :)
@HowtoAutomotive7 жыл бұрын
dannyninerempire very cool thank you for sharing!
@DaytonCarCare3 жыл бұрын
$200 it swap out a CPS that takes about 5 minutes to do. Cha-ching lol. Just serviced an Audi S4: radiator, AC compressor, intake manifold seals and oil check valves, oil/filter change, and an engine mount. Total labor $500. So $200 to do a simple CPS, yeah kind of pricey.
@carolmcenteewhite89628 жыл бұрын
Brian you are a jewel it went great super fantastic I am rolling thank you so much I just found a BFF!
@HowtoAutomotive8 жыл бұрын
Carol that makes me happy to hear! Great job!!
@benbrown90534 жыл бұрын
Did your husband do it
@whatspoppin3132 жыл бұрын
Someone just tried to charge me $250 to change this! 🤣🤣🤣
@MacAutoDiag2 жыл бұрын
What engine is this
@pcinoregon Жыл бұрын
Excellent video..thanks..you just don't know
@jeremytaylor4576 Жыл бұрын
Changed mine. Ran before changing it, now won’t start with new one in.
@jimbrown37703 жыл бұрын
Hey Brian I have an 05 ml 350 and I threw a code for the crankshaft position sensor. Is it pretty much the same as the one in your video? Also, is there only 1 sensor? Thanks for your help and your awesome videos
@HowtoAutomotive3 жыл бұрын
Yes there’s only one crank sensor. And it’s very common failure part.
@jimbrown37703 жыл бұрын
@@HowtoAutomotive could you tell me the part # by chance? I clicked on your link to Amazon and it's not working for me.
@caliaska46704 жыл бұрын
Thank you so much Brian! This video is the biggest help for me to fix my ml320.
@Wilt8v9211 күн бұрын
Is the ML430 in the same is it?
@brooster872 жыл бұрын
Sorry again. Auto correct. Crank sensor.
@jamespt20055 ай бұрын
Thank you I’m gonna try to replace mine because it’s not starting
@HowtoAutomotive5 ай бұрын
You got this!
@carolmcenteewhite89628 жыл бұрын
Ok Brian I will check it out.
@Luisperez-dc1kn7 жыл бұрын
Thanks for the great video
@HowtoAutomotive7 жыл бұрын
Luis perez thank you glad to help.
@garyyung12977 жыл бұрын
very helpful video, is it true that crankshaft position sensor can go faulty even without engine light coming on? thanks
@HowtoAutomotive7 жыл бұрын
Gary Yung yes see it a lot. The car will have an intermittent stalling symptom or a crank no start.
@RennaeFord5 жыл бұрын
Can you post a video on how to use the jack for the 1998 Mercedes ml320?
@HowtoAutomotive5 жыл бұрын
Rennae Ford if a ML comes in the shop I will.
@rw70513 жыл бұрын
I have mercedes gl350 diesel. jerky transmission when cold. p0336. FIXED. Best from underneath. TAke the plastic shield from below the transmission pan off, using 8mm wrench. Look above the starter and the LH fwd drive shaft and you'll see the plug on the driver side where the engine meets the transmission. It's at the 10 oclock position, just like on the Sprinter. I have a GL350,2013. crankshaft position sensor. metal shield over connector. use torx box end wrench.
@pcinoregon Жыл бұрын
That's cool.... so this is an easier way to get to that Bolt?
@mrneatglond37536 жыл бұрын
What was the vehicle doing why you have to change a sensor
@kentnoetico98676 жыл бұрын
It will generally become hard to start when hot; long cranking and sometimes stalling.
@garyyung12977 жыл бұрын
excellent helpful video thanks
@tamesheiabyrd6093 Жыл бұрын
Thanks so much a mechanic told my mom in order to change her crank shaft censor he needed to take out the water pump and it would cost her 1200.
@dannyramos80688 жыл бұрын
thanks buddy now I know where to start from I had no idea where this sensor was located at
@HowtoAutomotive8 жыл бұрын
Danny Ramos glad to help thank you for watching.
@brooster872 жыл бұрын
Sorry that code was in addition to the Crance code. Mass air flow is what it says. Can I just clean the mass air flow or replace it only
@grantstrong73194 жыл бұрын
Thank you so much for your help! Three videos on KZbin teaching how to remove this fing sensor all different. I was able to copy how you removed the worst placed screw in history and succeed. My upmost gratitude to you sir.
@HowtoAutomotive4 жыл бұрын
Grant Strong glad to help. Thank you for watching!
@waynegomillion49762 жыл бұрын
Appreciate it. Is it the same for an ml55amg 2000?
@FranklinCarreroluthier2 жыл бұрын
I have a ml320 from 1999 it works normally till the car arrives its normal temperature the car starts to fail when it is in minimum, the sensor might be the problem?
@brooster872 жыл бұрын
Thanks man. That is a great video. Changing mine this week. I’m getting an sensor code too. P0104. Is that just a clean or replace?
@garybourgeois70196 жыл бұрын
Will you always get a check engine light with a failed CPS? 99 ML 320 turns over briskly but will not start. Wait 15 minutes and it will start. Has died on me a couple of times when at stop. Have checked with ODB II and get no apparent faults. Still possible CPS?
@alanpazprado3 жыл бұрын
Signs that you need to replaced this is when engine got hotter and after you turn the car off it will not start until you wait it out to cool down ! Replaced mine already when it’s only 100000+ now im in almost 300000!
@SteveRobReviews8 жыл бұрын
Well done Brian..
@HowtoAutomotive8 жыл бұрын
I took your advice and turn the camera sideways. Thanks again for the tip.
@SteveRobReviews8 жыл бұрын
How to Automotive Need any help let me know, don't know if I can help but it doesn't hurt to ask LOL
@succatti733 жыл бұрын
Thank you!!!! I like to work on my own car and you're saving me!!!! GOD bless!!
@colinaglae26054 жыл бұрын
Thanx Brian, for your brilliant video on the on crank shaft replacement on Mercedes M320 !!
@mataataata74903 жыл бұрын
Thanks for the clear information I live in American Samoa working on a ml320, 2001 this was a great relieif
@reza493637 жыл бұрын
hey amazing video, my question is why do we replace the sensor, i have ml320 1999 and every thing works it just some times the engine stops and i have to wait for 30 mints or reset the battery then engine starts i have no killed switch or any starter or alarmes i saw you video but my question is this the sensor malfunction and must be replace? thank you very much
@HowtoAutomotive7 жыл бұрын
Reza Ahmadi stalling is one of the symptoms and no star is another symptom. There usually is a code stored in there PCM for the crank sensor.
@pimpoutmysandwich6 жыл бұрын
According to my AutoZone assessment, "when not replaced, vehicle may experience no start, hard start, intermittent engine shut down, misfire, engine cut out, excessive fuel consumption, CEL illumination, and/ or failed emission test" because the sensor helps regulate "ignition spark timing and fuel injector pulse timing" which is very important to maintain if you want to keep your engine running healthy or running at all over time.
@VINTAGEDS3 жыл бұрын
Great video. Do you you need to disconnect the battery before making this fix?
@KS-cu1zc4 жыл бұрын
Hello Brian is this for gas model or diesel bluetec same location same sensor. Thx great video
@brooster872 жыл бұрын
Thank you so much. Just did mine today. Great instructions.
@carollane4549Ай бұрын
((((((((❤)))))))
@bransky7 жыл бұрын
Thank you!!
@HowtoAutomotive7 жыл бұрын
David Bransky thank you for watching!
@acmehighperformance28262 жыл бұрын
Do these run in open loop if you pull it, unplug it and crank?
@eastside8517 жыл бұрын
My car lags when starting after sitting about an hour or two is this why? It has a bad crank sensor?
@ClintonSnow6 жыл бұрын
What's the part number of this crankshaft sensor? where can I buy the original crankshaft sensor for Mercedes Benz ML430, V8?
@HowtoAutomotive6 жыл бұрын
Clinton Snow there is a link with the part number is in the description of the video.
@SpenserRoger5 жыл бұрын
Lucky you have the v6, the v8 is way shoved back there.
@iantoriani7916 жыл бұрын
Good simple directions...Does the ml270 w163 2002 have the sensor in the same position?..Ianto.
@HowtoAutomotive6 жыл бұрын
Ianto Riani I don’t know if the center is in the same spot. I don’t see very many diesels
@vegetablehead6 жыл бұрын
what are signs that the sensor is going bad? my 2002 has a noticeable rough idle, but i just took it on highway trip and got 21mpg. also, a little tip on the 'vanity' cover. the left rear attachment (standing in front of engine) is NOT attached by rubber grommet, but by cheap piece of plastic clip. i know b/c i broke mine!
@kentnoetico98676 жыл бұрын
It will generally become hard to start when hot; long cranking and sometimes stalling
@davidagabi20776 жыл бұрын
hi My ML 320 seem to be having the same problems, It starts and run for like 20 mins and then turns its self off and after a 10 to 15 min wait, would start again and then repeat the circle all over again. Could it be the Crank.
@HowtoAutomotive6 жыл бұрын
David Agabi yes it could be the season or a Fuel Pump shuttling down. You’ll need to test for fuel pressure and also for spark to determine which one is the problem
@carolmcenteewhite89628 жыл бұрын
Now for the next project can anyone tell me why does my car whistle and has a rough sound when it is idled or in reverse ? It's a clk 320
@HowtoAutomotive8 жыл бұрын
Sounds like you have a vacuum leak.
@ttaei667 жыл бұрын
My ml320 start up then turn off I'd change fuel pump n fuel relay and put a new battery n still doesn't stay on plz need help
@HowtoAutomotive7 жыл бұрын
ttaei66 sounds like the crank sensor is bad but without testing hard to tell.
@achamitemiller88053 жыл бұрын
I thank you for that tip on location
@BrianaGettings4 жыл бұрын
What socket size did you use and what was your extension , a 3/8 drive?
@DaytonCarCare3 жыл бұрын
Yes 3/8 most commonly used
@karonsquaaad55717 жыл бұрын
Is that the sensor that's on top of the transmission in the back close to the fire wall, that's the only sensor I see that seems to be the crank sensor
@HowtoAutomotive7 жыл бұрын
KaRon Squaaad yes that is it.
@powerbylightfutureisnow15794 жыл бұрын
Number one best video 😂👌
@vivittronk7 жыл бұрын
hello!!...¿you need to use the STAR DIAGNOSIS computer after ????
@HowtoAutomotive7 жыл бұрын
vivittronk I used a Snap-on tool to just clear the codes. No reprogramming needed.
@vivittronk7 жыл бұрын
ok thanks!!
@aimeemontenegro81995 жыл бұрын
What if after changing the crankshaft and camshaft on this ML320 it still does not have power to accelerate and the rpms revs but the car does not speed at the time it is accelerated?
@HowtoAutomotive5 жыл бұрын
Aimee Montenegro The way you’re describing it sounds like a transmission issue. Start by pulling codes.
@Bugby672 жыл бұрын
Uh Oh😮
@cmgjunior525 жыл бұрын
What are signs your Crankshaft is going out or is out
@HowtoAutomotive5 жыл бұрын
cmgjunior52 The engine will crank and will not start.
@BriannadaSilva3 жыл бұрын
This helped for my ml350 too!
@HowtoAutomotive3 жыл бұрын
Yes
@carolmcenteewhite89628 жыл бұрын
Thanks Brian is that an expensive job?
@HowtoAutomotive8 жыл бұрын
If it's just a vacuum hose then no it's cheap. But if it's like a gasket leaking it could be expensive. Just pop off the engine cover with the engine running kind a listen for the hissing noise.
@harrellNOAA5 жыл бұрын
You are the man - thank you for taking time to make this video Sir.
@HowtoAutomotive5 жыл бұрын
Thank you for watching!
@dsheniai7 жыл бұрын
What is the size of the bolt?
@HowtoAutomotive7 жыл бұрын
Dan Shen it is a E8 female torques socket
@carolmcenteewhite89628 жыл бұрын
Brian I am going to try and replace the sensor by myself my husband is dead and I have no money to pay anyone to do it wish me luck lol.....
@HowtoAutomotive8 жыл бұрын
Carol sorry to hear about your husband. You don't need luck you can do this. Thank you for writing to me and watching the videos.
@HowtoAutomotive8 жыл бұрын
Hello Carol. How did the sensor replacement go?
@yamnjam6 жыл бұрын
I'm doing this very thing on my 2000 ML320 and am having problems getting the new sensor all the way back in and having the bolt hole line up with the thread. You make it seem so easy. It's the exact same sensor so that's not it. There's just no wiggle room to get leverage. One of the few times I'll need a guy to help me.
@HowtoAutomotive6 жыл бұрын
jamnjam i've seen if it's an aftermarket sensor that they don't slide down inside the hole. So what I have done in the past is use sandpaper and lightly sand the sensor on the outside to make it a little smaller and then slide it in.
@yamnjam6 жыл бұрын
That makes sense. I thought I was just super stupid, weak, or a little of both! I can't even get it back out. Got a buddy coming by to help and I'll be taking your advice. Thanks!
@HowtoAutomotive6 жыл бұрын
jamnjam there's not much room down there and he can be a pain. Let me know how it comes out thank you for watching!
@yamnjam6 жыл бұрын
The sandpaper worked like a charm. Too bad the crankshaft position sensor isn't what was wrong. I inherited it and it has 230k miles so it probably was due for a new one anyway. I've got a friend with a professional code reader coming by. I drove 200 miles the other day and 10 miles from home it just lost power on the highway, started sputtering, and then died after awhile. It restarted over and over but ran rough and moved only a few feet at a time. Got it towed. Next day started up & drove great for 2 blocks. Figured it was gone. Later, it went only 10 blocks and started the whole shuttering thing again. Towed again. Cranks fine, battery and alternator are great, so I took a stab at the CPS. I pray it's something normal like a fuel pump, not some weird obscure electrical problem. But it's not the sensor and now it doesn't even stay running. Now the fun begins.
@HowtoAutomotive6 жыл бұрын
jamnjam it sounds like a fuel pump. You can test fuel pressure when the problem is happening. There is a possibility of a bad mass air flow Sensor. Scan tool will tell you more.
@60snip69 Жыл бұрын
Great preview
@HowtoAutomotive Жыл бұрын
Thank you!
@raymccue43112 жыл бұрын
Thanks Brian
@HowtoAutomotive2 жыл бұрын
Thank you for watching!
@CJFilms10016 жыл бұрын
Awesome Vid
@HowtoAutomotive6 жыл бұрын
CJFilms1001 thank you!!
@CJFilms10016 жыл бұрын
You're welcome
@paulmac33074 жыл бұрын
Clear, concise, excellent. Thank you!
@HowtoAutomotive4 жыл бұрын
Thank you!
@DaytonCarCare3 жыл бұрын
I've read that sometimes you can get a crank no start condition if the CPS goes bad and also won't show any codes with OBD2 reader. Have you experienced this?
@HowtoAutomotive3 жыл бұрын
Yes I have run across that exact condition before. The car will not have injector pulse or spark.
@DaytonCarCare3 жыл бұрын
@@HowtoAutomotive Yeah I'm working on a 99 ML430, code for IAT so replaced MAF (checked wires to MAF plug they're OK), checked fuel PSI @ 50 should be 60 but I understand it's lower when cranking then gets higher after started (replaced FP anyway since level sensor bad), cleaned tube from EGR since common for them to carbon up (210k miles on vehicle) (have a 2000 E320 that had a no start condition and cleaning EGR tubed fixed that), also swapped in a good used ignition switch key sensor, so ordering a CPS since I can't think of any other issue that would cause this condition.
@DaytonCarCare3 жыл бұрын
OK installed a new CPS and it seemed to almost want to start. Then same symptoms of crank no start. Did some more research on M113 engine and read if it had gotten flooded by fuel prime the system by cycling the key to position 2 several times without cranking. Then hold pedal to floor and crank. That did the trick and it is running. It does have a rough idle so spark plugs next, has cheap Autolite one from previous owner and look over gapped and carboned. Going to replace with NGKs and see it it takes care or rough idle. (since TB, and EGR have been cleaned, also new Bosch MAF)
@DaytonCarCare3 жыл бұрын
Replaced the plugs and still same condition of crank no start and also a fuel smell. The old plugs smelled of fuel too. On further investigation I started wiggling the key then pushed on the main power plug going to key assembly then it started. Depending on where I pushed it, it would either make it start or (if running) would shut off if I pushed on it. So going to replace the ignition switch PN 1685451004
@HowtoAutomotive3 жыл бұрын
@@DaytonCarCare sounds like you found the problem..