How to Set Up A Paint Gun

[@tompeter7326]

Well, the outer scale of the pressure gauge is in BAR so base is in 2 bar, 1st. clear in 3 bar and second clear in 2.5 bar. Anyway thanks a lot for sharing your experience !

[@davidharrison8397]

I have an old sata 3000rp....it's my go to gun. I've got some iwata's and devilbiss guns too......but that sata spray's the best for me. My gun settings are very close to yours....great video

[@J.Lulo_]

Thanks for the kind words I always appreciate it.

[@LoloLolo-uk6jy]

Been trying out your settings over the past week. Getting some really nice finishes. It does look like you set the pressure for the clear at 40 psi.

[@J.Lulo_]

As long as your jobs are coming out nice 😊 from my instructions iam happy 😃.

[@DenzilEdwards-k2d]

Great video, great demonstration my brother

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it.

[@mfwwhelan7561]

At the beginning of the video you said that the gun had three controls :air, fluid and fan. In the subsequent explanation you only covered the fluid and fan controls. How to you set the air control? You only mention the air input to the gun but not the air knob setting. I'd be grateful if you could give me a bit more information. Thanks, Mike

[@J.Lulo_]

The air is controlled from the pressure regulator. In the video you see that the spray gun is connected to a pressure regulator and the knob on the pressure regulator controls the air pressure. When I mention psi in the video that’s the amount of air pressure you need to spray the base coat and the clear coat.

[@arielcastro34]

That knob stays full open or half way? I have a gun similar to yours I was able to adjust the Fan knob n the Fluid Knob n the analog regulator to settings just missing one . Pls Help I am about to shoot primer

[@J.Lulo_]

If you’re using a separate regulator for your spray gun you need to open the air on the spray gun all the way and control the air through the regulator.

[@rickymorenza1742]

I’ve been having problems with my clear. Thank you lot of runs and orange peel

[@J.Lulo_]

Your welcome 🙏. And Thank you 🙏 for the kind words I appreciate it.

[@DanielShaw-l3f]

Man you are doing something for the world of painters. Do that setting works for a LPH 400 1.3 orange cap. Let me know what psi setting up with that spray gun.

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it. And like I said in the video, you can use my settings to get started with your spray gun adjustments but you may need to do some tweaking to fine tune your settings to your specific spay gun and technique. Use my settings to get you started and make your adjustments as you need to. Good luck 👍 and thank you 🙏 for watching. Don’t forget to subscribe.

[@BearBudgetgarage]

Newer subscriber. You got some good videos, I need to go back and check out more of them. I'm doing some kind of paint n body work 7 days a week right now as a side gig, and in the evening I catch a few paint videos daily. Always looking for ways to improve

[@J.Lulo_]

Thanks 🙏 for the kind words I appreciate it. And it sounds like you’re hustling hard man. Remember to take a break sometimes you don’t want to burn yourself out. Good 👍 luck with everything you’re doing and I agree with you it’s always to good to keep improving your techniques. Take care man thanks 🙏 for the love.

[@CoreyHinojosa]

nice work brother. I'm running 2 digital 5500 sata, one RP other HVLP, (those are my clear guns 1.2 tips) 1 digital 3000 (base 1.3 tip) and 2 old sata 2000 (sealer and primer 1.4 and 1.5) and an old devilbiss finishline fl03 with the 1.8 tip for heavy primer surfacer. I run all my pressures at 2bar 29psi, fluid wide open (pull the trigger and screw in till i feel the trigger pushing forward. Air all the way open and 1/4 close. for distance from panel pinky and thumb rule for base but closer for clear and run super fast with 80% overlap (just for clear). a little trick I learned about a super flat finish straight out of the gun is that I DA the Primer with 800 and a interface pad. I shoot OMNI which I know it says 400 but was getting to much orange peel and did a experiment with 800 and beautiful. I always tack between each coat of the base. I'm going to try out your setting and see . thanks Corey

[@J.Lulo_]

WOW Dude you have a great spray gun collection. I have a SATA HVLP 4000 1.3, SATA jet 100 BF 1.7 primer, and 3M PPS 2 generation spray gun. I really like the 3M spray gun because you can change the tips for whatever the job is. It doesn’t spray as good as the SATA but I like all the options it gives me.

[@johnjackson6623]

By far this is the best video out there on set up. Teaches on my level. Any tips on spaying urethane on wood? You rock brother.

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it. Iam not sure about spraying wood because wood absorbs paint differently than metal. But what you can do is check to see how your application is absorbed into the wood and adjust how much the fluid out affects the finish on what you are spraying.

[@onurpinarbasi]

As far as I understand, when making the adjustment of the spray gun, after adjusting the pressure to 2 bars, we leave the fan size fully open and adjust it only by turning the liquid knob from fully closed. We will find out how many rounds we will turn according to the model of the gun and the tip.

[@eapauto]

Another great video sir. Really enjoy the knowledge you give.

[@J.Lulo_]

Thank you 🙏 for the kind words I always appreciate it.

[@ausonisaac5078]

I learnt something new and used it on my work thank you

[@J.Lulo_]

Glad it was helpful!I love to here when my videos are helpful. Thank you 🙏 for sharing.

[@alexextreme3026]

Na SATAJET 3000 B RP qual configuração de pressao no manômetro.

[@J.Lulo_]

English please.

[@nageshnaga4827]

Very good so beautiful in best thank you sir

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it.

[@oopoopod]

Thank you for this video.. at leas i have a clue how to set up my gun to start .

[@J.Lulo_]

You’re welcome 🙏.

[@asksteevies4941]

Thanks for your experiences, your a good man...

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it.

[@giuseppefiglioli5167]

Master julo ma la vernice a solvente a quanto va diluita inattesa di una vostra risposta vi ri grazio anticipatamente

[@J.Lulo_]

Most solvent based paint is diluted 2 parts paint 1 part reduction. 2:1

[@brentvangorkom8924]

Appreciate your advice!!

[@J.Lulo_]

Your welcome 🙏

[@larrymoody9074]

Where can i find a 1.2 nozzle for my vaper gavity feed spray gun?

[@J.Lulo_]

Iam not sure because I’ve never sprayed that brand spray gun before. Check online to see if you can find it.

[@keithcrews1460]

How do you determine what size nozzle to use ? my DeVilbiss has 1.3 to 1.8. Thanks

[@J.Lulo_]

The 1.3 is the standard nozzle for painting base coat paint. The 1.8 is meant to be used for applying primer.

[@yoyopg123]

good, solid tips. Thanks!

[@J.Lulo_]

Your welcome 🙏

[@sealisland1]

You set that to 3 bar(40psi). 2 bar is 29psi.

[@dlouque]

I too noticed that you are using the BAR number not psi. For example you stated 25 psi yet set the gun at 2.5 BAR that is a big difference in pressure. Please address this error.

[@rockyhamilton3578]

Thank u sooo much!!

[@J.Lulo_]

You’re welcome. Thank you 🙏 for watching.

[@LTVoyager]

I don’t think you know how to read your pressure gauge. You were setting pressures much higher than what you said you were setting.

[@drogba2k10]

Video suggestion: mixing paint, ratios. Solvent and water based

[@J.Lulo_]

Thanks 🙏 for the suggestion I will try to work on a video like that.

[@Chris_7575]

Is the same on sata 5000jet

[@J.Lulo_]

Yes it should be.

[@TheDopeShow81]

Holy smokes...start at 2 turns out and adjust from there. Don't start out full or it may get you in trouble.

[@J.Lulo_]

I close my fluid all the way and then I adjust from there. 2 turns out is a good place to start and then you can keep adjusting from there to get your desired spray pattern depending on the paint you’re using.

[@haule8418]

what tip size are you using for base. is it water or solvent?

[@J.Lulo_]

I am using solvent and the size tip iam using is 1.3. The 1.3 tip is the most common used tip for water bourne and for solvent.

[@Sno7373anon]

What kind of gun is that i love its paint job

[@J.Lulo_]

The Spray Gun I used in this video is a SATA 4000 B HEART & SOUL special edition, with a 1.3 HVLP nozzle tip. My favorite Spray Gun since I purchased it. SATA spray guns are one of the most popular spray guns in the industry.

[@TJA810]

Do you use the same gun for sealer, base and clear? Or do you have separate guns for each?

[@J.Lulo_]

I use my paint gun for painting base coat and clear coat. I have a primer gun for spraying primer because you shouldn’t use your paint gun for primer. A primer gun should have a fluid tip of between 1.6 or 1.7 to fill the body filler properly. Now there is a 3M PPS gun that allows you to change the guns tips so you can use one spray gun for everything. Here’s a video I made of the 3M PPS spray gun video link 👉kzbin.info/www/bejne/jIbRpJSJqaaDfNUsi=V30HIvd7FT1Z_73-

[@TJA810]

@@J.Lulo_ yea my primer gun is only a 1.4 rn so I've been looking into one with a bigger needle so I'll definitely look into the 3m gun 🙂

[@RubenMote-f2k]

How many days you finished to paint them all bro..?

[@J.Lulo_]

I don’t understand your question. What do mean be specific for I can answer your questions.

[@陳通明-o6u]

good information to me, thanks

[@J.Lulo_]

Your welcome 🙏. Thank you 🙏 for the kind words I always appreciate it.

[@tkflex2332]

Respects and bless 🙏

[@J.Lulo_]

Thank you 🙏 for the kind words and the blessings I appreciate it.

[@tkflex2332]

@J.Lulo_ I just started a job learning Autobody preparing and paint. It's a great opportunity and I want to be the best that I can doing it. When I get off work I will watch more of your videos. Respects brother keep on keeping on 👊

[@J.Lulo_]

That’s awesome 👏 man iam happy for you. It’s a great skill to have and when you gain experience you’ll be able to make a very good living. Good 👍 luck. And pay attention and listen and you’ll learn fast.

[@midobanderas4749]

U are the best

[@J.Lulo_]

Thank you 🙏 for the kind words I appreciate it.

[@serzgregory9124]

SATA HP? Важно всё: температура, вязкость, давление, форма факела, подготовка воздуха, расстояние, качество ЛКМ...

[@J.Lulo_]

SATA 4000 B HVLP 1.3 FLUID TIP.

[@giuseppefiglioli5167]

👍

[@FloridaWild]

I don’t count turns. Pull the trigger and hold it. Now turn the knob until it stops. Your fluid is now wide open. Otherwise, you’re choking the gun off.

[@J.Lulo_]

I do the count method because I like to adjust the spray gun depending on the kind of clear coat iam spraying. That helps me keep track of the fluid output depending on the viscosity of the clear coat.

[@FloridaWild]

@@J.Lulo_ I’ve set up guns that way for 30+ years, without issue. Comes down to spray technique also. So many painters don’t realize the distance they should be from the panel for perfect atomization. Most I see are too far out and creates issues with runs. You must perfect your technique with the guns you use and determine the distance from the panel and how fast or slow you need to move. Not a fan of DV1 because it’s too slow for my liking. I can spray with them, but just comes down to personal preference and what feels best for me.

[@J.Lulo_]

I agree 💯 percent brother.

[@2011NOT2DAY]

🔥🚒🔥🚒🔥🚒🔥🚒

[@jtekdryice]

Dope 👌

[@J.Lulo_]

Thanks 🙏 for the kind words I appreciate it.

[@hobbyautobodyfun9315]

I have a 4000

[@J.Lulo_]

It’s a great spray gun isn’t. I love my sata 4000. Best spray gun I’ve ever owned.

[@TJA810]

​@@J.Lulo_Have you ever tried sagola paint guns?

[@J.Lulo_]

No I haven’t painted with a Sagola paint gun.

[@TJA810]

@@J.Lulo_ Try one out sometime if you're ever in the market for a new gun. I have a base and clear one and I love them both a lot. Sprays similar to a sata

[@J.Lulo_]

Hopefully 🤞 I’ll get to try it one day. Sounds like a cool spray gun.

[@mosespau4908]

Ok

[@drogba2k10]

TOP G

[@J.Lulo_]

Thanks 🙏 for the kind words I always appreciate it.

[@taraz_avto_blesc995]

Привет я из Казахстана,хорошая покраска. Для меня SATA 4000/5000 лудшие пистолеты

[@J.Lulo_]

I don’t understand this language. English please 🙏.

[@mudassargujjar9987]

Hay my name is mudasar from Pakistan I am working auto painting job oman country ma I am job auto painting in the country ma jobs

[@J.Lulo_]

Hi Mudasar thanks 🙏 for watching and commenting. I hope 🤞 my videos are helping you with your paint jobs.