Hydraulic System Design

[@khanguyen-mv6sk]

Hello, do you have a video tutorial on simulating a hydraulic system? Do you use AMESIM LMS software?

[@_P0tat07_]

Cool program, but It would be cool if it gave you little animations of the components when running the simulations.

[@mskindia2841]

Do you have any guidelines on heat dissipation calculations / techniques

[@RahmatHidayat-en4lf]

How to set the limit switch for DAC. Do you have tutorial

[@PargatSinghbajwaps]

Hi How can i use this software, i need it, where to get? what is fees? fees yearly or lifetime? i want to use on Macbook (version 10.15.4 (19E287) MAC OS Catalina

[@surajkumar-yi4hb]

Is Simulation X is the name of the software?

[@hsyn.mo4]

sir, whats the full name of this software and how to get this? TX

[@sangeethav6257]

Please explain about hydraulic motor speed calculation

[@prashantbhat5846]

hi sir i need to design a foam punching machine .. which is operated by hydraulic system... can you give some information about that...like selection of type of pump,pressure(bar),valves etc...

[@muhriddinxonsobirov2837]

Hi Sir, how to connect with you?

[@saidmouhab590]

Hi Mr Mike how are you? I want to thank you for your vedios it's a missing makes hydraulique systeme clear and easy to understand I hoop to give more and more thank you so much

[@kamlesh-ce1dl]

Hi sir please provide me with a software name so I can daunlod in my system

[@sangeethav6257]

What is the software name and

[@OzeanX]

Hey Mike, thank you for the video, it helped me! Just one question: how can i put a force on the cylinder which changes with the Pistonmovement? like at the beginning its like 100 N, middle 20 N and at the end 60 N.

[@nadeemzzz5599]

May you please do a simulation including a one power pack, one directional control valve, one double acting cylinder compressing a spring or simply a single acting cylinder and one accumulator as an emergency source? In fact , I wanted to know how pressure changes in my circuit when the accumulator is used to compress a spring as an emergency source and pump is off. My guess: My pump will charge accumulator to its maximum value set on the pressure relief valve. Then I turn pump off. Pressure in my system will simply be the set value on the PRV. Then I will actuate my directional control valve to make the double acting cylinder compress the sring or compress the single acting cylinder. I should expect the pressure of my system to instantly drop to a value ( which is based on the initial force to compress the spring) .....pressure will then start from this value and continue increasing according to the compression force of the spring!!! Am I right ??

[@biramndiaye7376]

Bonjour je suis débutant et je voulais simuler un cycle frigorifique avec comme frigorigène le r134a pouvais vous m'aider svp

[@ashutoshsingh937]

Software name ....please

[@luizantoniodeoliveirachave2944]

Thank Sr. Excelent job. I used your work for my drilling design of hydraulic.

[@khanguyen-mv6sk]

Can you refer me to your simulation program?

[@luizantoniodeoliveirachave2944]

@@khanguyen-mv6sk I used Matlab/Simulink and Simscape. This article is basic abstract. PROPOSAL OF A SIMULATOR FOR A PRESSURE REGULATING VALVE IN A BLOWOUT PREVENTER SYSTEM Abstract: BLOWOUT PREVENTER (BOP) IS A FUNDAMENTAL BARRIER IN SAFETY DRILLING AND WELL COMPLETION OPERATIONS THAT REQUIRE AVAILABILITY AND RELIABILITY AS FACTORS THAT MUST BE EFFICIENTLY MANAGED. HOWEVER, STUDIES DEMONSTRATE THAT THE EQUIPMENT STILL PRESENTS A HIGH INDEX OF FAILURES AND UNAVAILABILITY TIME, WITH THE PRESSURE REGULATING VALVE BEING ONE OF THE MAIN COMPONENTS RESPONSIBLE FOR THIS PROBLEM. THEREFORE, THE OBJECTIVE of the research is to DEVELOP A MATHEMATICAL MODELING FOR THE CONSTRUCTION OF A SIMULATOR OF THE REGULATOR DYNAMICS, IN ORDER TO SUPPORT THE IMPLEMENTATION OF CONDITION-BASED MAINTENANCE STUDIES (CBM). SIX MAIN STEPS WERE ADOPTED WITH THE PURPOSE OF ACHIEVING THE PURPOSE OF THE WORK. ANALYSIS OF THE PHYSICS OF THE COMPONENT'S FUNCTIONING PHYSICS and the IDENTIFICATION OF OPERATIONAL PARAMETERS IN THE LITERATURE WERE NECESSARY, as well as the COMPUTATIONAL MODELING AND SIMULATION DEVELOPED IN THE SIMULINK/MATLAB SOFTWARE. THE RESULTS ACHIEVED IN THIS PROJECT STAGE WERE ADHERENT TO THE LITERATURE, REPRESENTED FOR THE PRESSURE LOAD CURVE PROFILES, SPEED AND DISPLACEMENT OF THE FLOW CONTROL MECHANISM. THE EVALUATIONS demonstrated POTENTIAL USE TO AID FUTURE FAULT SCENARIO ANALYSIS AND OBTAIN INFORMATION TO IMPLEMENT CBM IN HYDRAULIC COMPONENTS OF THE BOP ASSEMBLY. Keywords: BLOWOUT PREVENTER (BOP); PRESSURE REGULATING VALVE; SIMULATION; CONDITION BASED MAINTENANCE (CBM); FAILURE ANALYSIS Send me your email to send a complete article on other BOP components

[@hokeystifu7172]

it should have a relief valve

[@nickkrasovsky238]

Very cool thank you

[@m0nst3r_m1k3]

Why didn't you just use a relief valve at the start of the whole process? You could have moved your cylinder with less work. Does this program support different valves?

[@MikeCrowley]

With the programme you can set up all types of valves. And you could test if a relief valve would be beneficial.

[@m0nst3r_m1k3]

Mike Crowley great! Sounds like a very beneficial program. Thank you for sharing.

[@deepakmehta4883]

thank you sir

[@住宿费]

不会用啊 啊 啊