I Fixed A Vibrating Bed Remote 😃

🔵 We fix Macbooks & offer free estimates. rossmanngroup.com
🔵 Send us your Macbook for repair! bit.ly/sendmacbook
🔵 We'll send you a box with a pre-paid shipping label for your repair! bit.ly/sendyour...
🔵 We offer iPhone data recovery: bit.ly/2BDBX4G
🔵 We offer lab hard drive data recovery: bit.ly/labdatar...
👉 Matrix chat: matrix.to/#/#rossmannrepair-general:matrix.org
👉 LEARN HOW TO DO THIS:
› Beginner's guide: bit.ly/2k6uz84
› Support forum: $29/mo boards.rossman...
👉 CHIPS & COMPONENTS:
› bit.ly/2jaAOXM
👉 TOOLS USED:
✓ Soldering Irons:
› Louis' Hakko station(no tweezers): amzn.to/2cKkMyO
› Paul's Hakko station(works with tweezers): amzn.to/2yMvWNy
› Micro Soldering Pencil: amzn.to/2d5MWUP
› Hot tweezers: amzn.to/2yMvZsZ
› Atten ST-862D hot air station with bent nozzles: bit.ly/atten862
✓ CHEAP HAKKO ALTERNATIVES:
› TS100 soldering iron: amzn.to/2Gy1Fqz
› Recommended tips: TS-C4: amzn.to/33s3jpW TS-KU amzn.to/2QsKT36
✓ Preferred Soldering Tips
› Fine: amzn.to/2d5MgPn
› Flat: amzn.to/2JnsDBT
› GPU wicking: amzn.to/2w8chtB
› Micro soldering tip: amzn.to/2qUSFDh
✓ Microscopes:
› Microscope: amzn.to/2iLrE16
› Barlow lens: amzn.to/2yMKdKf
› LED light: amzn.to/2nzfPT2
› CHEAP alternative microscope: amzn.to/2rTlHbj
✓ Soldering/Repair Supplies:
› Solder: amzn.to/2cKkxUp
› Desoldering braid: bit.ly/2otflOX
› Flux: bit.ly/amtechflux
› Solder paste: bit.ly/amtechso...
› THICK insulated jumper wire: amzn.to/2rvtD0A
› THIN insulated jumper wire: amzn.to/2I47DQY
› Kapton tape: amzn.to/2yN0xuq
› Tweezers: amzn.to/2d5NBpi
› Blades: amzn.to/2ByWnvF
› Freeze Spray: amzn.to/2BySozw
› Conformal coating: bit.ly/greencoate
› Conformal coating curing pen: bit.ly/uvpen
✓ Diagnostic tools:
› USB amp meter: bit.ly/2B2Lu5W
› USB-C amp meter: bit.ly/usbcamp
› On-Screen multimeter: amzn.to/2jtgY9K
› Multimeter Probes: bit.ly/fineprobes
› CHEAP multimeter: amzn.to/2zjkg8U
› Bench PSU: CSI3005P bit.ly/benchsupply
› Phoneboard: phoneboard.co
› Boardview software: pldaniels.com/...
✓ Ultrasonic Cleaning:
› ALL MACBOOKS & CELLPHONES: Crest P1200H-45: amzn.to/2ITSQdw
› PRE-TOUCHBAR MACBOOKS & CELLPHONES: Crest P500H-45: amzn.to/2Qrnhf8
› CELLPHONES ONLY: Crest P230H-45: amzn.to/2QsckKG
› Branson EC cleaning fluid: amzn.to/2cKlBrp
✓ Desk supplies:
› Desk: amzn.to/2yMShdZ
› Chair: amzn.to/2LB8bUB
› Fume Extractor: amzn.to/2d5MGoD
› Work mat: amzn.to/2yMtlTR
› Outlets: amzn.to/2yNsZwo
› Gloves: amzn.to/2iUfumS
› Durable lightning cable: amzn.to/2yNHzUt
› Fine tipped snippers: amzn.to/2HGt4XB
✓ Screwdrivers:
› iPhone bottom screw: amzn.to/2yNwX8p
› Macbook bottom screw: amzn.to/2AKMdVb
› Torx T3: amzn.to/2zjtxxH
› Torx T5 amzn.to/2BLNDn4
› Torx T6 amzn.to/2B0XIfA
› Torx T8 amzn.to/2CpWp68
› Phillips #0: amzn.to/2AJaHhM
› Phillips #000: amzn.to/2yNqsCl
✓ RECORDING EQUIPMENT:
› Work cam: amzn.to/2QjHnt0
› Overhead cam: amzn.to/2eAH0oT
› Work mic: amzn.to/2WGIhzw
› Home mic: amzn.to/2xfampC
› Microscope camera: amzn.to/2icVQoG - mine is DISCONTINUED, closest one I can find.
› HDMI capture: amzn.to/2iyGcle
👉 Affiliate:
› Buying on eBay? Support us while you shop! www.rossmanngr...
› Rossmann Repair Group Inc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com
👉 Leave a tip for us via cryptocurrency if we've helped you out:
› Credit card: bit.ly/postames...
› Bitcoin: 1EaEv8DBeFfg6fE6BimEmvEFbYLkhpcvhj
› Bitcoin Cash: qzwtptwa8h0wjjawr5fsm0ku8kf40amgqgm6lx4jxh
› Dash: XwQpZuvMvU44JT7C7Uh6xHvkSadzJw9fMN
› Dogecoin: DKetsoCvwa2hF29ssgUA4Wz4hxT4kj3KLU
› Ethereum: 0x6f6870feb48f08388ee345cf0261e2f03d2fa310
› Ethereum classic: 0x671bfd61ba87edf6365c97cea33d66ba73645510
› Litecoin: LWnbTTAjojZQt68ihFJFgQq3cYHUsTcyd7
› Verge: DFumZ5sMhi3JktLQpsTVtV9xUt3zKDrcZV
› Zcash: t1Ko3FkphQYoQroQc8k2DVk4WKMAbmNR8PH
› Zcoin: a8QdvArHmdRYe1MjiqtP6jDNe6Z4JgnRKZ

[@blank-mq8ef]

man i grew up watching you and i think the most real thing ive heard so far is the fucking manual bit

[@rossmanngroup]

Every time I read an instruction manual it is useless bullshit. Whatever it is that I get stuck on is not mentioned in the manual. Whatever I am trying to troubleshoot is not in the troubleshooting section. Instruction manuals are mostly useless. Schematics are awesome. Instruction manuals suck.

[@alanowa123]

Manuals are for when everything goes right and when something is wrong there is a customer support. The problem is that there is always something wrong and almost never customer support is any good 😅

[@johnpienta4200]

kzbin.infoUgkxSgphfqZPEBWW4NAyrNhbkPt6H4AzGvvD?si=_-_BkNIrqGDFUQJh Your moment of Zen. When I heard this I laughed so hard.

[@JessicaFEREM]

@@rossmanngroup the schematic is the autism manual, the normie manual is the one in the box

[@Yeenuwu]

We're reaching seconds per frame territory

[@mauzen_]

wa

[@BritishEngineer]

qwq…

[@BritishEngineer]

Oh god I just realised you’re also from the midlands, a furry and probably like engineering. wow we have something in common.

[@danieltoth9742]

The additional time spent on each slide is what allows Louis to explain things in the proper detail. This is a great presentation.

[@danieltoth9742]

@@BritishEngineer nevermind, I'm outta here

[@it-sd]

Old school Louis repair. I miss these videos. Good times. Thanks, boss.

[@rossmanngroup]

Thanks for watching!

[@anti_honey]

Hopefully people from Inventec see this and start sweating hearing you call them out, I love your total no-nonsense stance against all kinds of bad business practices

[@rossmanngroup]

When it comes to items on my website, I have never dealt with a shittier company. What they did to the people who were selling the flux using a similar formula to what they used to make was a shitty thing to do. www.globalsmt.net/industry-news/inventec-takes-legal-measures-to-protect-their-amtech-brand/ When they say they are protecting their brand, in my opinion, what they actually mean is _"we want the ability to sell NC-559-ASM as NC-559-V2-TF. If someone else makes we ACTUALLY USED TO SELL AS NC-559-V2-TF, we will sue them."_ Technically Inventec owns the trademark. However, what do you care more about? Sanctity of the trademark "amtech" or "nc-559-v2-tf", or getting the same formulation that you paid for? The legal owner of the trademark has the legal right to change the formulation of what they sell under that trademark without informing you; they can sell whatever they please as _"Amtech NC-559-V2-TF"_ They could sell toilet bowl cleaner as NC-559-V2-TF and it would be legal. What matters more? Ownership of the trademark, or the switcheroo they pulled selling a different formula under the same name? What do you care about more - another company using Inventec's trademark to sell NC-559-V2-TF using a similar/same formulation Inventec used before they switcheroo'd it with a different flux, or Inventec *_ACTUALLY PULLING A SWITCHEROO AND SELLING A DIFFERENT FORMULATION ENTIRELY UNDER THE NC-559-V2-TF NAME?_* You can talk all you want about the letter of the law, but the spirit of the law is what customers care about. They broke the spirit of the law, and then used that to pummel their competition into oblivion. They asked me to help them with PR. I told them in plain terms, there's the letter of the law, and the spirit of the law. Nobody gives an F about your trademark, they care about buying NC-559-V2-TF that feels & smells like the old NC-559-V2-TF before you pulled a switcheroo selling ASM as V2-TF. Do that instead of trying to get me to ruin my reputation defending this nonsense. I told them: I won't _"help"_ your reputation by doing what you're asking: - *I'd ruin mine.* The last straw for me was not telling me there's a $400+ shipping charge and surprising me with it anyway. if there has to be some special $400+ shipping for this order... you could tell me, so that I can modify my order accordingly. It's a shit thing to do to someone who's spent $100,000-$200,000 on your products over ten years who spent that ten years evangelizing your products. Same as the shit thing they did changing the formulation & destroying amtechdirect. I have no respect for that company's management or ownership. They knew my grievances about this for over six months now and never did anything to make it right. There is nothing they could tell me at this point that would change my mind, or opinion of them. Anything after the fact would just be damage control.

[@nadiaplaysgames2550]

@@rossmanngroup they shot themselves in the foot so damn hard maybe should of said "we hecked up what do you want rossmann to fix this iusse"

[@HANKTHEDANKEST]

@@rossmanngroup Jesus that's greasy, what a bunch of assclowns.

[@blackrifle6736]

@@rossmanngroup *Louis, please continue to expose this nefarious behaviour. Inventech's switcheroo impacts thousands of electronic repair facilities worldwide. Army Material Support Command assigned an NSN to the original product so they will have an interest in this development. Across many decades never had a fume extractor on any bench I've worked at. Never bothered me, still love the smell of Kester 44 in the morning... Cheers!*

[@burnburn645]

@@blackrifle6736 makes me curious what that smells like :D

[@chrisjc2k]

The real question is - did you get your flight? I miss these videos of you just sitting there repairing something and soldering and just talking about different random things. Please do more of these :) I find them very relaxing, interesting and wonderful to put in the background while I do other things.

[@rossmanngroup]

I DID!

[@quickplayzRok]

i’m not entirely sure the problem was on accident

[@Omnihilo]

My first thought when I read the title. 😂

[@boris---]

Duuude I missing Luis repair videos so much.... I was addicted on watching them in one part of my life...

[@ChrisModjeska]

Become a travel blogger and just repair random shit around the world. People can't afford to do shit anymore but at least we can live vicariously through you.

[@stryhuns]

for us viewers this sounds dope, but i'm sure Louis wants just peace and quiet in his life now

[@Agent_Ice0]

"If you wanted a screw I would have given it to you." That and the wink made my day.

[@Premier-Media-Group]

I clicked as soon as I saw "I fix..." by Louis MFin Rossman. And yes, that would be a natural character arch for your channel - fixing disposable electronics.

[@kewrock]

The seething rage just below the surface. I love it!

[@OpticIlluzhion]

You can take the New Yorker out of New York but you can't take the New York out of the New Yorker

[@kewrock]

@@OpticIlluzhion we're not all angry like that. Although I am 🤣🤣🤣

[@markbrown8097]

Thanks for showing the proper way to solder. I've seen too many you tubers do the dry blob and rake job and it drives me crazy!!!!

[@ElementalMaker]

Feel like I'm watching claymation. Bringing me right back to the 90's, thanks Louis for the nostalgia. Also please name it Rossmans Raunchy Rectal Plug Repair Group

[@lasciencedelamusique6245]

I'm watching it all since its a real Louis' on the bench video!!! You the repair goat bro!

[@rossmanngroup]

Thank you sir! That means a lot. There are a lot of good repair people on KZbin you should check out now though. It's not 2013 anymore. I'm not the only game in town. Lots of great and talented people way better than me for you to watch!

[@slendi9623]

Who do you recommend?

[@rossmanngroup]

piernov jesse cruz(vcc board repairs) tim hermann(tcrs circuit) jessa jones(ipad rehab) jason(sts telecom)

[@slendi9623]

@@rossmanngroup tysm!

[@jasongreene303]

@@rossmanngroup It's not all about the repair, it's that you can entertain people! The object being repaired is what your nerdy audience is into.

[@justanotherguy6345]

love the number of rossman vids we've been getting lately keep it up or don't I'm not your mom

[@kevinklien90]

I have this old multimeter that suddenly stopped working about a year ago that would turn on but refused to measure anything. I did notice some corrosion, so I did what you did and cleaned ALL the solder connections and that fixed it lol Thanks!

[@grandtheftauto1233]

Spectrum finally delivers lol

[@michellemokracek3361]

You’re the best! Your sarcasm and anger are sadly justified.

[@MattTrevett]

You've taught me so kuch over the years. Working on figuring out a broken massage gun right now and wouldn't even think it was possible if not for your videos. Been watching a long time.. thank you.

[@Rooonga]

Day made seeing Louis repair again! Been subbed since the first NY shop, so it feels like ‘the old days’

[@HANKTHEDANKEST]

Louis, this has nothing to do with the subject at hand--I just wanted to thank you for distracting my ADHD ass while I do a forced break from the little automotive job I'm doing today, because eating lunch is hard. That's all, just a "thank you" for helping to distract me enough into eating lunch. I hope *you* are having a lovely day.

[@rossmanngroup]

Thank you for the kind words & for wishing me a lovely day! I hope you are doing well too man.

[@MoonberryJam93]

Idk about making your channel about sex toy repair, but I'd love to see a recurring series about fixing devices deemed "unfixable" by the manufacturer out of sheer spite

[@blackrifle6736]

*Long-form Louis is the best-form Louis! For techs and EEs, ADD and OCD are gifts, not a curse.*

[@kahrhoshe]

Over 2M subs. Congrats just noticed today.

[@rossmanngroup]

It's a fake number, this won't pass 10k all day. Don't pay attention to subscriber numbers on this channel, they're not real.

[@arghpee]

@@rossmanngrouplouis is so real for this

[@bradhaines3142]

@@rossmanngroup most channels are like that, a few i watch are over 2 mil with MAYBE 50k views in a week

[@kahrhoshe]

@@rossmanngroup yeah I always look at ratio of views to subs. GN has one of the best ratios on KZbin at least when I looked last. I’ve seen some that have 1m subs and the views are 500k so you can see the real views. Still think that of most Sean Evan’s hot ones has the best ratio views vs subs.

[@rossmanngroup]

steve at gamersnexus earned his exceptional ratio. He earned every subscriber and all of his success. I have nothing but good things to say about him based on every interaction I've had with him - in person, online, on the phone. He's a consummate professional who cares about his work and cares about his viewers. A genuinely good dude.

[@rodrigomaero]

It’s great to see you again doing repair streams! Sorry for not being there, College is killing me… but hopefully it’ll end soon. Hope you are doing all right Louis!

[@RoseKindred]

Hey, you can make a new niche. Repair devices for "creators." As for the time crunch, go on set and fix everything before the pizza-man comes.

[@Syncopia]

This feels like the rossman of old. Time sure flies!

[@hemxd2691]

never change louis

[@foxronyo]

You probably worked it out by now, but the Sync and Pair buttons need to be inserted from the inside.

[@rossmanngroup]

Bruh I spent an hour fixing the original remote just so I would never have to read a manual to figure out how to use those buttons!

[@originalksd]

@@rossmanngroup 0:01:48 vs 1:05:38 and seeing how the 2 buttons block the batteries cap to shut = We are just mentioning this so you don't end-up with a broken tip of battery cap -> there for with tape on remote to hold it in place -> and there for with all that stickiness - sticky mess, not cuz you'll use these....

[@shtewps]

This is dope, Louis. Please keep bringing these loose, but still technical and educational videos. Love the walkthroughs without the formality. Learning some good tech sprinkled with humour and masculinity. I can't fucking think of anything better in this world. Keep inspiring. We thrive on this.

[@Rozbujnik_Rumcajs]

"Out of spite repairs" chapter

[@zamaraaldo]

I suggest you to point the remote at the camera to see if it works, as cameras can see IR light

[@nfcapps]

I love the small appliance repair channel

[@MiJoPaFo]

@14:30 Manuals are like Lisa Simpson as Flanders would say. "The answer to a question nobody asked." 😂😭

[@lgg2304]

I'm crackin open and fixing remotes all the time so when heard Rossmann was doin it... I had to see this!!

[@RobinhooodGFX]

Just bought a $500 microscope to fix broken consoles. Feel like i’m late to the Ross party, just discovered his channel, having so much fun fixing stuff

[@ponyforhire]

Listining to Louis for over an hour as I cook and eat, makes me feel less lonely

[@kvbk]

There is so many better things to smell than solder flux. ~Louis Rossmann

[@AcornElectron]

Crazy that Big Clive had exactly same item today! I think. Sounded similar.

[@marcus_cole_2]

Hi Louis Rossmann, I haven't asked you about this yet, but since you're doing this particular video, I have to inquire. I live in Canada, and I bought a vibrating bed with an adjustable frame for over $500. The remote control had two pieces: one being the control board and the other being the remote board. They literally just soldered the remotes together with blobs of solder. Fortunately, it fell and broke the solder joints, and currently, I haven't found anyone who can fix it or repair the ruined solder points. I would love to send it to you and would be willing to pay a reasonable fee. You could even make a video about it, I don't mind. The fact that I have to buy a new remote for $300 to $500 is ridiculous, considering the bed itself costs that much and it's only wireless. Please reply back and let me know what I have to do to have you repair this. I think you're the only one who could.

[@Shadowtrot]

OK, you got the vibrator working, and maybe if you read the manual the sync button would work too, but Louis, I saw no fans spinning. No fan spin, no fix.

[@redkurn]

welcome back louis, hope you have as much fun with the 2017 mbp logic board i sent in (ironically delivered the same day you filmed this), parts or repair have fun. oh and please mock my attempt to solder an inductor back on (already broken so why not try 😂), bought the laptop for $50 and it was worse off than advertised.

[@marklarz4399]

If buying isn't owning then piracy isn't st.... oh... wait...

[@rossmanngroup]

You wouldn't download a remote control to a vibrating bed, would you?

[@majstealth]

@@rossmanngroup i know me, i would fucking do it, right now!

[@omarothman12184]

soon, people would 3d print it....probably, maybe​@@rossmanngroup

[@Fridelain]

​@@rossmanngroupBring back phones with IR blasters

[@ElvenSpellmaker]

​​@@FridelainThe OnePlus 12 randomly has an IR Blaster

[@joncue0304]

Thanks for your videos. The variety is not only informative, but mixes it up enough to keep my interest. That's saying something since my ADHD doesn't normally allow for that :). I have never had any desire to repair a circuit board, but still thoroughly enjoy your content. Keep up the good work.

[@Panda_5020]

Thanks for the repair Louis, I am the same way with trying to repair my stuff but usually I am alot less successful probably due to not having much experience with it. Also the ADHD thing is so real. I will space out during lectures and teach myself the material when I get home, and I will only read manuals if it is documentation for a program

[@stevenford4719]

I see you have started the anti sponsor mentions in your videos with the flux mention well done please keep it up

[@Breadbored.]

I like seeing the concepts used to fix computers demonstrated with simpler, cheaper products. Practicing the basics with cheap stuff that I can get my hands on and not be afraid to permanently destroy in the name of learning is a lot of fun. It's also nice to be able to fix those cheap products and save some money, considering I'm likely to have a hundred or more cheap products like that break before I see one of my computers require any repairs. Throwin stuff away $20 at a time adds up after awhile.

[@durragas4671]

And LOVE the stop motion capture.

[@glitched100]

I just bought the same exact bench you have in your shop for soldering work. Great work bench for the price

[@dalyxia]

Changing the formula and calling it the same item is what EVGA did with a power supply, where they changed the pin layout of the modular sata connectors without renaming or even naming it v2 or something which destroyed a customers harddisks. Gamersnexus has a video about it.

[@Fridelain]

Can't find it.

[@marcogenovesi8570]

Quality Content, repairing random stuff at 6 in the morning

[@AshnSilvercorp]

it's always great when Louis is a happy repairman with a wild soldering iron.

[@joeledwards6587]

Hi Louis, I think you were struggling to put the battery cover back on because the sync+pair buttons were being inserted the wrong way, it looks like you need to insert the buttons from the inside, not the outside (ie the larger part of the silicone buttons should be pressing up against the buttons on the PCB) and that would stop them easily falling out as well. Fun video to watch, thanks :)

[@evensgrey]

That's and interesting difference between me and Louis. I like reading the manual. I've been known to read the manual FOR FUN. Then again, I work in tech support. Somewhere I have a manual that says, "Tech Support We Read the Manual for you."

[@kevinley8321]

it was a fun trainwreck to watch. my first computer was an apple II GS. At 14 it cost twenty five hundred dollars and did very little and home ccomputing didnt get better for like a decade

[@tastymonkey]

Overall I like all content that Louis puts out. The repair ones are great because you also get some random commentary.

[@Nebbia_affaraccimiei]

wow I cannot believe u just now catching up with the whole AMTEC debacle

[@rossmanngroup]

I have a fume extractor. The difference in smell wasn't something I really noticed because I usually have headphones on while I work so I can keep my fume extractor on the highest setting and I always have it RIGHT up next to the board. I don't enjoy the smell of any flux. I was literally the last person to have a clue about the changed formula because the smell was never different to me, because between allergies + fume extractor, I never smelled it :( When I found out, I felt uninformed, confused, and ashamed. I have to have been the last person to know... :(

[@MaleficWeegee]

​@rossmanngroup Don't worry! I didn't finish the video before looking at the comments, so I still don't know what AMTEC is yet, lol.

[@beejls]

I had some miserable paperwork I had to deal with. This was the perfect video to accompany my misery.

[@rubenmejia4881]

Preach Louis!

[@fanwlkr]

I think the moral ABC is always be clean ;)

[@Cat_in_The-Box]

Campaign to stop gaming companies from destroying games has started.

[@wellseverett5128]

Probably should pull the tactile switch overlay. A bit of heat works. Could be some moisture still under them. And FYI you can hold the IR emitter to your phone camera and see it flash. Camera IR filtering might reduce the light. Or just tack a regular LED in parallel to the emitter for a check.

[@pauljs75]

If wanting to do something outside of computer repair: I think there's a market for doing resto-mod stuff to older electronics from the 1980's and 1990's. A lot of stereo stuff was made better then than it is now. Particularly if it's something that was made in Japan. It's just needing Bluetooth audio connectivity added, aux-in if it doesn't have one, better batteries if portable, and re-capping and cleaning of switches and contacts, speaker swap or re-coning. Showing the challenges and process of getting that done would be interesting.

[@coya8coy175]

Dr bronner’s unscented lip balm is the only brand that moisturizes my lips AND doesn’t cause an allergic reaction. I also make my own.

[@DordiHOTS]

This is what we love and want

[@rgar2255]

Bummer I missed it live, keep up the "good" work!

[@friedrichfreigeist3292]

I wouldnt mind learning more about differend kinds of power supplies and how to repair them!

[@joncue0304]

You can see the impurities coming off the solder joint while you're filing them. That's pretty cool.

[@raymondeemon125]

At 49:05 on the circuit board you had flipped R36 around when it got stuck to your solder iron and you resolver it back on idk if the direction matters. Just wanted to let you know!

[@alexis0a]

Louis fixing something and show us... boy this day is getting better!

[@DPLS77]

this was both funny and educational, I miss these style of videos, keep it up!

[@Lazdinger]

Ah, good ol repair video.. solid ✊

[@jasonjazzz5]

after the cock ring repair, we dont wanna know why the remote needs repair louis. you do you man... :P

[@ryandoyle4344]

Full live explains it got washed

[@ΓιανναραςΚαπα]

not the first time Louis fixes a vibrating object!

[@Yogsoggeth]

I recently subbed and I love this. Your content is the goat!

[@rodrickbourque]

I use MG Chemicals 8341 No Clean Flux Paste. Very nice flux in a syringe.

[@hateeternalmaver]

Louis fixing his scope while fixing a remote - fixception! ;P

[@mikeymaiku]

yes, the best types of repair

[@jilbertb]

Oh, it actually IS a remote... ☹ I thought it was something else! More of a... tool. 😂

[@Atlessa]

KZbin: Yo, this video has 60 FPS Louis' cam: Naaaaaah, fam. It's 60 SPF. ( ͡° ͜ʖ ͡° )

[@Dajenken]

Interesting video, same remote here now I know how to fix it if it ever goes into the wash

[@AntiJock6]

Feel like I had a "Heat the board" moment with those back buttons, Pretty sure the big part of those buttons go on the inside, they shouldn't be able to fall out from the back. But I am too lazy to rewind to check how they originally were. Hope you catched your flight.

[@bigMax1337]

remote backlight is the new fanspin

[@DaveRepairs]

FAN SPIN ! It's been too long, good to see you doing something useful

[@ReneNieuwenhuis]

Big Clive also did repair a vibrator today… coincidence? 🤓

[@clarkesuperman]

This video was neuron activating. Thank you king

[@captainmidnite93]

I remember when Coke dropped real cain sugar for the deflavorized corn-crap and didn't change the name. Switched to Pepsi which had the same corn crap , but, they weren't the ones that weaseled me. And I was just a kid then . Kudos Mr Louis!

[@nemesis851_]

I would LOVE for US DOJ contact Louis as a PRIMARY WITNESS

[@evensgrey]

To quote Isaac Arthur: If brute force isn't working, you're not using enough of it.

[@jamiethomas4079]

I love the repair videos and resonate with your with frustrations from these companies. I have a 4k ip camera that got struck by lightning(hit my transformer) and blew up the chip for the poe power supply inside. I can almost read the chip model from images filed with the fcc. Sucks that a $130 camera goes to waste cause I cant get a part model number. Fixing golf cart controllers is a profitable endeavor. I fixed one that was a simple diode replacement. Or from a few failed mosfets. And most of them cost $300-600 and up. I raise hamburgers but dabble in electronics, so I watch for the farming right to repair info and electronics repairs like this.

[@ruben_balea]

SDaPo (Shenzhen Dapo Communication Co) makes various models of power supply modules for IP cameras that are quite cheap and available on Aliexpress. And on their own website they have the pinouts. In case you've never used it the Aliexpress search engine is a piece of **** and 95% of the results will be for totally unrelated things but if you search for "sdapo" or "PoE module" (without the quotes) you may find something suitable. You can also take a photo of your PoE module and search on Google for similar pictures. Disable the flash for better results

[@gabrielcamacho6247]

You can watch if the infrared led is working pointing it to a camera. It is the same as the fan spin on a macbook :P

[@vevenaneathna]

miss these lol

[@FlexDRG]

Hey Louis... Less mouth, more hands. You'll finish faster... 🤣🤣🤣🤣✈️

[@SArthur221]

i use an s5 instead of remotes. although these days i mostly tend to use a note 3

[@anotheruser9876]

Out-doing BigClive Today is see.

[@davidchang2015]

the first minute is the kind of modern genius for the modern KZbin algorithm

[@RandomGreenFishPhone]

I fixed my smart TV remote, in a way. I didn't like how there was a microphone built into the remote and I was paranoid that my voice would be recorded and sent to LG and god knows who else, even when I chose the option to disable that functionality (who knows what their closed-source software is doing). I no longer connect the TV to the internet now, but I needed to until I got my computer setup for media. But why would there be a microphone in the remote in the first place? If my remote is nearby, I am just going to press the buttons... Anyway, I ended up completely removing the microphone from the remote and while I was in there I disabled the Netflix button that I would accidently press a few times a week because it was right next to the back button.

[@Foolish188]

Fix a remote control? 1 Change the batteries 2 hit it on the edge of a table 3 buy a universal remote 4 buy a new TV

[@kazi1]

Very nice

[@ckmondaviable]

Louis, making everyone come again…