Mavic 2 Landing Gear "Leg" Replacement Without Replacing the Arm/ Landing Gear Fix Easy No Soldering

Ever snapped your landing gear "Leg" off your DJI Mavic 2 pro or Zoom? We'll here is how you fix it without solder or paying top dollar for repair. Get your arm for landing gear replacement here : U.S.A ebay.to/2U5rW7T
UK ebay.to/3cU323A
Dynamite RC tools U.S.A ebay.to/2IEr84m
UK ebay.to/2U0mjaW
In this tutorial I will show you step by step how to fix your Mavic 2 zoom or pro landing gear and have it replaced in no time. No experience necessary I will help you replace your broken leg fast and easy.

[@ultimusstatic]

Great video. A little tip, you can actually turn the led sideways and sneak it through that gap without using a dremel tool.

[@phoenixdronepros6416]

Great video - I followed right along and replaced my leg with no problem. Took about 10 minutes and NO soldering!!!. THANK YOU!!!!

[@jeffredodd]

Thanks for posting this. This helped me repair my Mavic Air 2S that had a similar broken part. Seeing how you took things apart helped me to save a few bucks especially before vacation.

[@brandonroberts7185]

thank you for posting this, well done

[@chadmcphail]

Really appreciate this post!!

[@andypetersel9183]

Thank you! Was in the same situation, and when I realized replacing the leg means dealing with the LED situation I got stuck. Only 2 solutions I could see was desoldering/soldering the wires or dremell the plastic so I can fit the LED trough. You gave me confidence to apply the dremell solution. In the end, I noticed the LED looked like the soldering has broken off but it turns out everything worked fine when I tested the drone. 👍

[@joeaudet88]

Still a great video. I just used it today to replace a busted leg. Thanks!

[@kutabareseniorita6036]

I'm gunna have a Go now. That led is a pain!

[@ryanmalagara3232]

Great job. Did mine. Thank you!

[@kylepeterson]

thanks for uploading this tutorial. I used you Dremel example for the LED insertion to fix mine. thanks!

[@MarcoGennai]

This helped! thanks!!!

[@chrisanddd]

Nice work brother thanks!!

[@andrewallan6802]

Thank you for this

[@jasonvinton8257]

Just did this! Thanks! If you don't have a dremmel tool, I just used the various torx ends to and phillips heads to make the hole bigger and bigger, and just cut out the plastic on the leg that was getting tossed. All good

[@frank01709]

Just done this fix worked great. Thanks so much for posting helped me out immensely 👍👍👍

[@FatherandSonHavingFun]

Your welcome glad I could help.

[@djmochaman]

Just had my first light crash and YES YOU are a life safer.... Thanks for Posting boss this will help a lot..

[@FatherandSonHavingFun]

No problem, glad I could help...

[@MindFloodMedia]

Thanks man, gave me the confidence to do it myself. Easy peazy, no dremel needed

[@FatherandSonHavingFun]

Your welcome, glad it helped.

[@user-by7hu4gb5d]

Help me lot!❤thanks~

[@pallebobandreasen3461]

Thank you very much, your video helped me

[@joeskillzz3668]

Cool video

[@njrivetelite]

This exact damage + prop damage happened to me on a job this past Monday with my Mavic 2 Pro. The lateral sensors didn't catch the object to it's left and crashed causing the mavic to hit various things on the way down but somehow caught itself. I found it hovering. I still had many shots to get.. so I replaced the damage props and flew her with the damaged landing gear. I obviously didn't want to press my luck on further jobs so I didn't want to leave it damaged. I don't have the time to send it off to be repaired so I was searching KZbin with the hopes I'd find a way to repair it myself in a much more time sensitive manner. Found this video and glad I did. I had to dremel both gear to release and then push the light through the new piece. They sell them on Amazon for $8 for a pair. Instead of spending $50-200 for a repair.. it cost me $8. Not bad at all.

[@kris30ful]

Thanks 👍👍👍

[@daltonterrell4860]

Thanks for the video bro. Helped me a lot

[@FatherandSonHavingFun]

Your welcome glad I could help.

[@pinnerphotography2580]

Thanks for your video BIG BIG help!!

[@FatherandSonHavingFun]

Glad I could help, thanks for watching and commenting hope you have a great day.

[@vivalaina1]

Just broke the leg piece same spot! Thank you for the video, its a life-saver!

[@FatherandSonHavingFun]

No problem, grad I could help.

[@ajooba29]

Yea, literally this happened. Wasn't too sure about the LED popping off. Thanks for the video. I didn't replace it because the plastic seemed to get right into place and I think it'll be okay for me. The next crash, I'll probably have to get a new leg anyway. Thanks a lot for making this.

[@vivalaina1]

@@ajooba29 I did not change the leg piece either. Mine cracked halfway and still holds it together. I guess till next time :D

[@rhertwig11]

Thanks so much for this!

[@FatherandSonHavingFun]

Glad to help, have a great day. .

[@claudiobonifacio2839]

Obrigado pelo vídeo, vou tentar trocar no meu. Abraços aqui do Brasil 👍

[@billybrackman5143]

Thank you ;-)....

cool , thx !

[@FatherandSonHavingFun]

Glad to help. Thanks for watching and commenting hope you have a great day.

[@Scrizzy561]

what size Torx drive do you need for the landing gear screws?

[@kutabareseniorita6036]

I glued mine on, after stepping on it. Then it was stepped on again. Took ages to get all the glue off ans the 3 main screws but that LED is a pain in the ass! changed my dji fpv landing gear and antenna board x100 easier.

[@jaquito57running32]

Is it the same for the Dji air 3

[@pedrolopez8057]

you should mention which tori bits you used

[@igorsilvamorais4633]

Which key did you use to disassemble?

[@2004skylinegtrr34]

I need to replace the front right leg, but have a front left leg only. So the atenna will be face differently. Will that affect my drone in any way?

[@lukeapy5335]

Hey there thank you for the video, I was wondering if the air 2 and the air 2s use the same leg? I broke my air 2s and need to repair just that part. Thank you!

[@FatherandSonHavingFun]

From everything I've seen from the air 2 and the air 2s, they use the same leg just different sensors....

[@lukeapy5335]

@@FatherandSonHavingFun so I would be fine just to order the replacement landing gear rn?

[@FatherandSonHavingFun]

Yes.

[@Stompdown98]

Where did u get the dremal tool with a volume nob?? I could really use one of them

[@FatherandSonHavingFun]

LOL, the advantages of editing....thanks for watching and commenting hope you have a great day.

[@garethh6962]

I’d leave battery off next time you work on it

[@CiprianTurutea21]

Hi there, I can't take off the antenna from the new leg, looks like locked...any advicee?

[@FatherandSonHavingFun]

Make sure all the rubber cement from the inside the leg, it's very difficult to get all of it off.

[@CiprianTurutea21]

@@FatherandSonHavingFun I'm refering at the minute 3:15, you take out the small black ball (that should be kind of rubber locking) and then just pulling out it goes. Mine stays there....

[@jamesmcneil8093]

How would you handle if the antenna was cut in half?

[@FatherandSonHavingFun]

I would probably solder or epoxy the peices together.

[@xtremeheightsproductions]

Are you asking for a friend?

[@IJUSTWANNAFLYDJIDRONES71]

I did it but its harder than it looks.

[@SJPhotography999]

are you in atl?

[@FatherandSonHavingFun]

No, I'm in North Carolina....

[@vallerographics6597]

That ending was worrying me. I need to make sure I can clip the light cover back on securely

[@vallerographics6597]

It worked ! Thanks

[@FatherandSonHavingFun]

Your welcome, glad it worked out....

[@sirtubemaster]

is the Mavic Air 2 & Mavic 2 Pro takes the same landing gear

[@FatherandSonHavingFun]

I'm pretty sure it doesn't...

[@sirtubemaster]

@@FatherandSonHavingFun I guess we will see because i ordered them :) couldn't find a model replacement that showed only Mavic 2 and the picture looks the same as mine so fingers crossed

[@FatherandSonHavingFun]

Let me know if it works, good luck.

[@sirtubemaster]

@@FatherandSonHavingFun they came in today and very clear they are not the same. Thang goodness for Amazon prime ;) The pictured diagram was not exact

[@FatherandSonHavingFun]

Thanks for letting me know, I'll put that in my data bank.

[@jordya.7444]

What if you accidentally pulled the led off before watching this video, any tutorial? 😢

[@Sanncheztv]

Where can I get a new arm?

[@FatherandSonHavingFun]

Should be a link in the description.

[@Sanncheztv]

@@FatherandSonHavingFun thank youuuu very much!!!

[@FatherandSonHavingFun]

Your very welcome, best of luck to you.