Please comment your opinion on this video and don't forget to like , subscribe , share & press the bell button if you enjoy the content . thanks for watching .
Пікірлер: 41
@CoolIdeasDIY-qv1nz9 күн бұрын
Interesting video colleague👍👍👍
@metallantik9 күн бұрын
I always watch your videos, you have a good channel and interesting ideas, I subscribed to your channel ❤️👌
@metallantik9 күн бұрын
I pinned your comment
@CoolIdeasDIY-qv1nz9 күн бұрын
@@metallantik Thank you my friend I also watch your interesting videos, you have a very good channel👍🤝🙏
@metallantik9 күн бұрын
@@CoolIdeasDIY-qv1nz thanks 🙏❤️
@emilalmberg10969 күн бұрын
You are very creative, a few more years of experience and you are a metal master!
@metallantik9 күн бұрын
Thanks a lot ❤️🙏
@nikfreedom28989 күн бұрын
You can't press such a bearing on the inner ring, you need to do it on the outer ring. You damaged the bearing during installation.
@metallantik9 күн бұрын
The point was correct 👌
@kcelf534 күн бұрын
Another junk tool.
@wolfgangtatzel37067 күн бұрын
Great Idea - thank You 3:50 too dangerous!!! 5:59 Super Ball Rolling -great work
@metallantik7 күн бұрын
Thanks ❤️
@AliEbrahimi-p8z9 күн бұрын
excellent as always🔥👏😍
@metallantik9 күн бұрын
Thanks ❤️
@rezadrvishi36659 күн бұрын
Interesting and creative👍👏
@metallantik8 күн бұрын
❤️
@farshadkarami81534 күн бұрын
very excellent
@metallantik4 күн бұрын
❤️
@schrauber-holgi5108 күн бұрын
Eine radial belastbare Lagerung besteht immer aus 2 Lagerstellen, die möglichst weit von einander entfernt liegen. Bei eine Mitlaufenden Zentrierspitze z.B. ist ein Nadellager im Grund des MK Schaftes.
@metallantik8 күн бұрын
Danke, es war informativ 👌
@vahideh.sh189 күн бұрын
Einfach geil 😍
@metallantik9 күн бұрын
❤️😍
@parnuzutech8 күн бұрын
good job👍
@metallantik8 күн бұрын
Thanks
@imanmoradi44269 күн бұрын
Very good
@metallantik8 күн бұрын
❤️
@RaheemIkaz9 күн бұрын
Keep it up
@metallantik9 күн бұрын
Thanks ❤️
@leila79639 күн бұрын
perfect 😍👌
@metallantik9 күн бұрын
😍
@Klaus-v1i8 күн бұрын
Bis auf das einpressen des Lagers ( in diesem Fall wird am Außenring ein gepresst und nicht am Innenring ! )sonst OK .
@metallantik8 күн бұрын
❤️👌
@DaveTecho7 күн бұрын
really bad way to push a bearing...
@johnm8405 күн бұрын
Better ways to align angle for taper. Perhaps you did it off camera.
@metallantik4 күн бұрын
❤️
@ahmaddarvishi-wy4vk9 күн бұрын
mardiiiiiiiiii
@metallantik9 күн бұрын
Marde mardaan
@ThomasSchlemm4 күн бұрын
Ein Hammer ist grundsätzlich nicht geeignet um in die Drehmaschine gespannt zu werden!