New Rage Cycles 2017-2018 R6 Fender Eliminator Install | SportbikeTrackGear.com

[@chicagor6700]

Brian's mechanical abilities and demonstrations never cease to amaze me. Learned a lot just from his vids back in the day. Hope to see new install videos on the New Rage products on the newer 15+ R1.

[@anarchy8793]

I just put mine on my 2020 R6 your video helped the process go some much smoother

[@sportbiketrackgear]

Happy to hear you found this helpful. Enjoy that new R6! - Van

[@FrenchysPlaysTV]

I was going to ask about resistors because most people don't bring that stuff up. I appreciate that you did.

[@sportbiketrackgear]

NP thanks for watching! - Van

[@Kalasbra]

i even ordered this before i got my 2018 R1 !! installing it tomorrow! Thanks!!

[@sportbiketrackgear]

We have been selling a ton of these for the 15-18 R1 since we added them to the site. Look awesome on the bike for sure. - Van

[@darnellhamlin3917]

I've installed this on my 2016 zx10 front and rear. Very clean and very bright

[@menace2society310]

That’s a good look for a tail tidy 👍🏻

[@sportbiketrackgear]

The design in unique and the quality is good. Really like the OEM connectors on the wiring harnesses. IMO this New Rage Cycles stuff is going to be super popular. - Van

[@diemman70]

I’ve always liked their products.

[@butlerville23]

I really wish you could do the 2018 R1 installment for this eliminator. Great video by the way bro 👌🏾

[@danielpichardo4878]

Just installed last week! Love it! Video helped so much! Thanks

[@sportbiketrackgear]

You are welcome and thanks for watching! - Van

[@evercastillo3318]

Yes I really like this incredible

[@_Fox_Dye]

For the one's hating in the product "you can't have both signals and fender eliminator for that price" for this specific bike 😉 this product is awesome💯

[@oSnapMillerTime]

Its pretty crazy this is the only plate mount that is so slick. I looked and looked and nothing comes close to this and it is insanely expensive.

[@sportbiketrackgear]

New Rage for sure has some of the coolest fender eliminator kits. As for the price everything is too expensive. Go buy some eggs. - Van

[@K_24_]

2:27 Hahaha, "big piece of shit boat anchor" hilarious. Really sweet fender eliminator but man its so tucked up, cops must give you shit for this one.. might try my luck anyway though.

[@wardock03]

I had the same fender on my ninja 300. Never got pulled over because of that. Just keep the license plate light and you're fine

[@ttuckerTNT02]

You should check out Intelligent Lighting Systems. They use the daytime running lights and can turn those into blinkers. Really sick lookin stuff!

[@sportbiketrackgear]

I will try to look into that. - Van

[@xKYLAFORNIAx]

love it when Brian starts swearing... lol it's peak Michigander ;)

[@sportbiketrackgear]

Real people use real words. - Van

[@geese7484]

Thank you 🙏🏽 this video really helped me

[@sportbiketrackgear]

You are welcome and thank you for watching! - Van

[@ali19186]

Just got done putting mine on stock front turn signals it’s flashing normal

[@ali19186]

Kinda wish the led for tag light was a bit brighter

[@sportbiketrackgear]

Thanks for sharing that. There must be enough load on the circuit with the stock front signals. - Van

[@frankdahtank1234]

Awesome look. I’m planning on getting it for my 2015 r1. Seems easy to install but my only question is, is the plate stuck to one position? I don’t want to get pulled over cuz the “plates couldnt be seen”. Will the plate be fixed in one spot or is it adjustable?

[@oSnapMillerTime]

A lot of riders dont even ride with plates

[@DisplacedLogic]

Almost make me want an R6.... Almost.

[@sportbiketrackgear]

Sounds like you have a 675, also a kick ass bike. - Van

[@DisplacedLogic]

Sportbike Track Gear The new 765. I’ll look into seeing if they fit! Thanks for the info!

[@syxxphive126]

Gotta ask Brian, why would you ever want to remove your mirrors on a street bike? The tail looks fantastic, but I’m always worried about visibility issues. I want other drivers to see me.

[@blue03r6]

I've never tried the bar end mirrors but a few guys told me they can see behind them better with them than stock mirrors.

[@rybrownw]

When you are wearing gear you really can’t see the cars behind you using the stock mirrors on a sport bike 🏍

[@syxxphive126]

Roy Brown I haven’t had that problem. Not only do I think it’s dumb to remove the mirrors, in many states they’re required.

[@HollywoodStyleLimo]

Jessie VaineoHurst no it’s not dumb! If you ride a sport bike when you lean forward you can’t see nothing on the stock mirrors, you can see much much better using bar mirros. Even a single bar mirror is more useful than the stock one.

[@MADLITS1K]

Why do people that are constantly scared ride? Lol some places people ride with their mirrors tucked in anyways, especially if it’s a place where they are allowed to lane split, stop whining 🤷‍♂️👎

[@SquidRider]

"New Rage Cycles" has some hefty price tags, holy cow. Love the looks though.

[@anarchy8793]

I paid 150 for mine

[@MADLITS1K]

Lol if you compare it to cars aftermarket tail lights range from 3/400- 1000s$ .. this is cheap for what you’re getting tbh

[@Crustyto3z]

Imforomative, great video!

[@IAMTHE1_]

Hey I'm in Michigan to😁😁😁

[@sportbiketrackgear]

My favorite state is this great country of ours. - Van

[@blue03r6]

wow that's a nice frigging kit. ok off topic brian, what model handy industries lift are you using?

[@wade_v4]

i wanna know if i can adjust the plate angle to normal before i buy this

[@sportbiketrackgear]

You will have to bend the bracket if you want to change the angle. - Van

[@0878825983]

Very good idea. bro!

[@evercastillo3318]

ok thanks friend i like i will buy it

[@sportbiketrackgear]

This kit looks amazing on the R6. - Van

[@twowheelsr6]

It flashes to fast when you install it. What can you do to put it back to normal settings??? That’s the reason why I haven’t order this yet.

[@sportbiketrackgear]

You can install the New Rage Cycles Dual-Load Equalizer. Here is a link to them on our site: www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/ - Van

[@twowheelsr6]

Sportbike Track Gear okay thanks.

[@vauldur3385]

If you had to, could you bend the plate frame to make it "more legal?" or will it crack the finish off?

[@sportbiketrackgear]

It will bend a bit before you have any issues. Just don't push it too far. - Van

[@lucasberntson8100]

I just installed this on my 2019 r6 and now my front accent lights and my tail/break lights don’t work? Any suggestions on fixing this??

[@sportbiketrackgear]

You need to double check your work. It sounds like there is an issue with the install. Retrace all of your steps very carefully. Hard to diagnose this over the KZbin comments. - Van

[@2elements539]

Did you figured out the issue tail/break light ? I just installed the fender eliminator on my bike. But now the tail light don't work

[@dyfahey]

Is the installation similar to the 2015+ R1? Will you be making an install video for that?

[@jimnicketta5926]

at 15:08 is there any reason the tail light didn't turn on when you turned the key on? At 20:00 it's on, so did anything else need to happen to make the tail light turn on?

[@sportbiketrackgear]

Did this a while ago so memory is a little foggy. I would guess I had it unplugged while I was testing the plate light. Nothing special needs to be done to get the tail light to illuminate. - Van

[@keloniomannamoinolk7153]

8:27 hello sir, that cable when tightening the screw is crushed between the metal and the plastic? really?

[@sportbiketrackgear]

It needs to be routed in the center of the bosses so it does not get crushed. - Van

[@chrisknight3681]

Looks sweet but no doubt in Texas that’s gonna get you pulled over and even worse the military police aren’t letting that one go.

[@sportbiketrackgear]

Important to know your area before installing something like this for sure. - Van

[@SuperTigerBalm]

@@sportbiketrackgear can you bend the plate to make it slightly more visible? if yes im purchasing .

[@sorasswag]

Is this the same for an 2017 r1 like follow the same steps?

[@sportbiketrackgear]

Yes the install would be the same on the 2017 R1. - Van

[@cjschmitt4882]

Where you racing bro? Grattan? Gingerman?

[@sportbiketrackgear]

Max and I will be racing Wera at Grattan here in MI and Barber in AL this year.

[@cjschmitt4882]

@@sportbiketrackgear nice...I raced GLRAA & Were way back in the day....Grattan much fun! Happy race season!

[@LoneWolfTD]

Are reusing the washers that were under the oem bolts?

[@FuturisticViper]

does this company support older bikes i would love this kit on my 2009 ninja zx6r

[@sportbiketrackgear]

New Rage is expanding their catalog all the time, but they have not done anything for the Kawasaki ZX-6R thus far. Keep an eye on our site, we are updating as they offer more products. - Van

[@loganburnett4263]

Is that plate legal in VA?

[@sportbiketrackgear]

Sorry I am not familiar with the regulations in VA. - Van

[@MasterJjt242]

same process for r1?

[@sportbiketrackgear]

It will be very similar for sure. Thanks for watching! - Van

[@StyloMakes]

Is the license plate bracket stuck in that position or is it able to be moved more upright?

[@hyperwolfco8021]

TRAPAHOLIC I’m pretty sure it is a fixed position

[@_Fox_Dye]

TRAPAHOLIC you can bent it a bit that is what i did

[@norberto570]

How much is cost that I just buy some part from you guy

[@quagmire1130]

I live in Cali so I would get hassled a lot for the license plate lol

[@sportbiketrackgear]

For sure there are different levels of enforcement everywhere. - Van

[@chrisbrown-gr2xy]

i watched this even i don't have a superbike

[@sportbiketrackgear]

You have to admit this is a beautiful fender eliminator kit. Love those LED's. - Van

[@JusttCalebb]

Is there anything to slow down the flash rate?

[@sportbiketrackgear]

Yes you can install a resistor to slow the rate of flash. Here is a link to them on our site: www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/

[@4id4n97]

Anyone know if this would work on a r7?

[@sportbiketrackgear]

New Rage his fitment for the R7. We have the parts here to shoot an install and will try to rock that out next week. Here is a link to them on our site: www.sportbiketrackgear.com/parts/yamaha/yzf-r7/2022/?_bc_fsnf=1&brand=382 - Van

[@georgeuntalan1]

can you put that in r1 also?

[@pyrusmasterdan1]

Hahahaha piece os boat anchor 😂

[@abhijithks6827]

Can this get in india

[@sportbiketrackgear]

We ship internationally using DHL or USPS. - Van

[@evercastillo3318]

can i put the r6 2020

[@sportbiketrackgear]

Yes this will fit the 2020 Yamaha R6 as well. - Van

[@evercastillo3318]

@@sportbiketrackgear ok thanks friend i like i will buy it

[@markaldrintangco2881]

Does the hazard signal still work?

[@sportbiketrackgear]

Mark Aldrin Tangco yes they are still fully functional. - Brian Van

[@markaldrintangco2881]

Sportbike Track Gear last question sir! Is it compatible with the integrated tail light? Both NRC signal light and integrated tail signal lights blink together?

[@sportbiketrackgear]

Yes it will work with an integrated tail light no worries. - Van

[@jrsantiago69]

Alsome product just pickup 1 also for 19R6

[@Rohit-qt2ve]

How bright are they?

[@sportbiketrackgear]

They really pop IMO, visibility will not be an issue with the signals on this kit. - Brian Van

[@hoanghatn123]

can I install that for my yamaha R3?

[@sportbiketrackgear]

No they do not have one yet, pretty sure New Rage is working on one now. Keep an eye on the site, we will add it as soon as it is released. - Brian Van

[@hataaurider]

It's expensive more brand?.....Not bad..

[@keloniomannamoinolk7153]

Ok but 150 dollar???? you are crazy.

[@sportbiketrackgear]

We sell a metric shit ton of these, super cool part IMO. - Van

[@keloniomannamoinolk7153]

@@sportbiketrackgear I think it's perfect that I sell a ton of this product. Obviously people buy without knowing. Just two pieces of metal. amazing.

[@oSnapMillerTime]

Link to one that looks as good. I agree its insanely expensive but I cant find anything else short of just not having a plate.

[@lelandsmith3827]

Apparently this guy doesn't realizes you need a torque wrench to torque bolts

[@sportbiketrackgear]

If you need a torque wrench to install a fender eliminator you should really consider taking the bike into the dealer to have it installed. I will guarantee no experienced technician will pull out a torque wrench to install a fender eliminator. - Van

[@Mike_Oxmall]

isn't that plate illegal? Tucked in?

[@sportbiketrackgear]

This really depends on the area you live in and how something like this would be enforced there. IMO if you are not street racing odds are you will not be hassled. - Van