Nissan sentra 08 step motor

[@robertor.contreras2877]

Thank you so much.. I fixed my Nissan sentra thanks to your video.. have a great day

[@damianmunoz7726]

Gracias por tu video me ayudó arreglar el problema de mi carro Dios te bendiga

[@mikestanley6331]

If your step motor still isnt working and you get the step motor or ratio code its because there is a pre drilled factory hole that holds the lever back. If you pin it to the left as the video shows, when you torque it all down and pull your pin it will not be engaged therefore your tranny wont shift right. Lever should be to the right in video. How do I know? Because I did it. Good luck everyone.

[@paulkhazzaka6262]

Hi i have the ratio control valve stuck, do u think i can grind it until it get smooth? Will it damage the transmission?

[@ernestomoreno2596]

Is it good idea to reused the old transmission fluid when you changing a part like stepper motor??

[@splash5974]

@5:28 the ratio control valve. I just got the P1778 code, which is also a stepper motor code. But after inspecting valve body, i noticed the ratio control valve doesnt move very freely. It almost feels a little sticky inside the bore? Its al cleaned up, but still feels a little sticky. What should i do now? Replace entire valve body?

[@brandon701252k]

Mines too on my 2012 Altima

[@gibson7654]

I'd say, yes, the whole valve body would need to be replaced.

[@Angi_E7]

Aw crap

[@mohamedkhelili9311]

Did you end up replacing the whole valve body ?

[@JV_214]

On locking in the shifter rod while lifting the valve body back on, did you really lock it in through the tapped hole instead of the tiny drilled factory hole?

[@mikestanley6331]

I agree. Its the little pilot hole and not the bolt hole. If you do it like this video then when you pull it out, it wont catch the pin. How do I know? Because I did it. The arm should be to the right in the video and held by a small hanger or something and not the left side.

[@romnitorres9915]

Thanks I needed to know this

[@mohamedkhelili9311]

@@mikestanley6331 so when he is putting that little pin to hold that thing he was spouse to put it in the second hole on the right the small one ? Because I’m sure you are right but his car was driving after lol weird

[@ernestomoreno2596]

Rey thank you for such amazing. I have a 2008 Nissan Sentra and through me code p1777 which is the stepper motor. I replaced the stepper motor and two plates came apart abd I am not sure how to put them back. Do you a video how to put back the part where the solenoids goes and the other plate underneath, or can I put the all thing together and them install it back?? Help please thank you

[@aftab100]

Thanks for this video. .today i have given my nissan sylphy 2.0 which is not running above 20km per hour speed.Diagnostic shows stepper motor problem. This happen after driving car for 200 km on highway. Cost of changing is USD 400 in Malaysia on 2.3.2019.Hope after changing step motor , car will perform.

[@xxgodxx9306]

Sd3075 did it work?

[@aftab100]

Xx GodxX yes. It worked. But other than step motor there was some electrical issue to sensors too were there. After repairing back wiring of car now it is working perfectly.

[@collegekrane6141]

What was the other issues?

[@abelduran9710]

I just replaced the step motor but now it’s not shifting gears do you know what my problem could be? I also use the Castrol CVT fluid with said it was compatible for Nissan but the fluid was red. I notice everyone else using the green Nissan stuff. How to replace the whole valve body?

[@mohamedkhelili9311]

Did you ever fix it same shit happened to me did all the work and it’s acting up

[@AnythingEverythingGh]

How many bolts did you remove from the valve body to bring it down?

[@ozziemartinez1484]

Google... nissan sentra valve body bolt removal procedure. .... hope this helps

[@xxgodxx9306]

What’s that one part that you said it has to be smooth so you won’t get the code if it’s not the step motor

[@JeffersonNascimento-di5cb]

Salvo meu cambio... Estava colocando no outro furo para encaixar no pino do cambio

[@TheMDBandit]

Great video sir. Im actually working on mines at the moment🙏💪👍 oh and guys mine is a 2007 Nissan altima and its exactly the same as in this video. If anyone wanted to know

[@HamzaKhan-kj9wy]

did it work?

[@TheMDBandit]

No lol. I just ended up swapping out the whole transmission 😁👍🤘🔥

[@Angi_E7]

Ok so what if the ratio control valve is not smooth like u said? I cleaned it out and its not helping I don't know what to do

[@dangelomack1]

Im seeing ratio control valves should have spring but mines dont have one

[@jair8808]

Did you reuse the oil pan metal gasket? It seems like it might leak. Maybe some gasket maker??

[@reycaro8545]

Juan Alberto Isidro I use gasket maker is better

[@jair8808]

@@reycaro8545 Thank you!!!

[@CEONTHEMAKING]

Is there any reprogramming necessary when disconnecting and re-connecting the valve body?

[@johnjoseph7382]

supposedly only when replacing it

[@jcmeek83]

Great video , Can’t wait to tackle the project

[@masonh9997]

Thank you for your advice your help your video help me a lot with my car problem 👍👍👍

[@jt8280]

Brother Great job ! Should I buy a OEM or aftermarket stepper motor ?

[@sparklingsams3155]

I got the same code it reves up and down on D . Any thoughts?

[@josefranciscoesquertalaman3827]

Excelente buena Información

[@akeemrichardson4463]

Hi I did everything you mentioned in the video and my car still isn't shifting from low gear. I changed the step motor and still nothing.

[@edgardfigueroa5533]

I'm curious because I'm about to do the same. Did it ever fix the problem????

[@splash5974]

It doesnt always fix the issue. Sometimes its internal damage, but the computer sees it as a stepper motor code...

[@babyjoacademy]

I have the same problem with my Nissan it drives but doesn’t shift so Do I need this part or How do I fix it?

[@robertbodkin9057]

How pissed was you when you found out that the replacement stepper motor has a longer shaft than the OG ? I did the same thing you did on my 2010 Rogue . Keeping my fingers 🤞🏻

[@splash5974]

Same length shaft, just might have been extended further than yours at the time you installed it. It will self adjust as you drive. That shaft fully extends and fully retracts as needed. The main issue is not always does the stepper motor fix the issues, even though it gives the stepper motor code! Alot of people have same symptoms after replacing the part. Hopefully it works for you!

[@heavymetalredneck7973]

Good video bro, i appreciate you!

[@ammonrivera6657]

Hey Rey, where did you buy the replacement step motor? Would it be the same step motor for the Altima 2.5 s?

[@brandon701252k]

I got mines from Amazon

[@blacktorbet8611]

i am replacing the valve body on my 2012 nissan juke, it is the same one. when i pulled the old valve body off the car, a round bushing fell out of the trans. i noticed the same bushing in your video, Where does it go?

[@HmHaroon88]

i think it goes to shift connector rod, at 0:45 seconds in the video, you see a rod hanging? when you put back the valve body , there is a collar like round metal part ( what you may call a bushing) that goes over this rod and then you secure it with a bolt.

[@javiersernan9310]

excellent info Rey, can you tell me where do you purchase the Stepper Motor and solenoids and pressure switches New? thank You!

[@reycaro8545]

you can get it on ebay the step motor is like $30

[@JavierGarcia-or9uz]

I replaced the step motor and still having the same issue, any ideas?

[@songbird372p7]

Me too but driving ok actually really good when I first got in it,we'll see when I drive it more mayb it will turn off🤞🏾

[@JavierGarcia-or9uz]

Did it fix the problem

[@HmHaroon88]

@@JavierGarcia-or9uz same here. I then added an after market cooler and it fixed the problem.

[@edgardfigueroa5533]

@@HmHaroon88 after market cooler what is that?

[@HmHaroon88]

Edgard Figueroa The transmission has a fluid that needs to be cooled. Normally it is cooled by conventional radiator. I literally just added another radiator so that more cooling can take place. You can search after market transmission cooler and You will find many on amazon or auto stores. I got mine from amazon with all the hardware and installation instructions included.

[@ozziemartinez1484]

No one shows the bolts that support valve body to transmission. There is about 30 bolts and I dont know how to bring valve body down without completely disassembling it.

[@ozziemartinez1484]

@@torredrakeford7825 thank you so much ur a lifesaver.

[@prnc5812]

Very good explanation

[@vandoauguste3700]

Hey Rey, Thanks for sharing your experience with us, how can I contact you?

[@quennierapuza222]

Thanks for sharing your Video!

[@100ega8]

Before you replace the step motor, What was the highest RPM you get on the car??

[@reycaro8545]

4000 rpm you can get the step motor in eBay

[@100ega8]

The thing it's that I don't know if the code p1777 can cause not to accelerate almost like there's no pedal o no throttle body.

[@xxgodxx9306]

100ega spark plugs that what my car had it wouldn’t go for anything

[@jacobperez2664]

Thanks man I have a nissan altima 20011 it's having that isues too

[@LovelyScorp7789]

Hello. What is the name of the part connected to the step motor that needs to move smoothly for it to work?

[@SmartRetailTherapy]

I have the same question. I think this part isnt springing up as Ive seen in other videos.

[@splash5974]

@@SmartRetailTherapy same with mine! Feels like its sticking in the bore. Its the ratio control valve.

[@Angi_E7]

So what did you do did u fix it

[@chevymanken]

Rey CaRo I have 1778 step motor code slips mostly at higher speeds, whats your thoughts 2008 Nissan sentra w/2.0

[@Charlie21G]

Im having that one rn too

[@Charlie21G]

Did you ever fix your problem?

[@Emmssa]

Same code I have, and the car doesn’t shift sometimes

[@kiserajuniourautogarage6029]

How can I get a step motor for my Nissan dualis j10

[@atifabusalim7217]

Very nice vedio But how to check wiring be for replace valve body And to check operation steper out side in pench More thank for you

[@b4322558]

my cusin had 2009 nissan roug with that code and the dealer dont sell that part u ieather got to buy a vavel body i think it 1200.00 or buy a trans for it

[@honorableD]

What was the torque wrench for the stopper motor

[@fajarisnanto]

Do you erase dtc error first before start to run the car?

[@reycaro8545]

Yes

[@reycaro8545]

yes

[@atifabusalim7217]

Very nice explanation But you will not explanation how to check wiring from out side valve body I think it must be first be for remove ed valve body Much more thank you for you

awesome. thanks for sharing!!

[@arnelmariano8278]

what is the size of ur engine? mine is 2009 sentra 2.0, is it the same with yours? the cvt transmission i mean?

[@reycaro8545]

Arnel Mariano yes is the same transmission cvt and same size of motor

[@saidgure1444]

Thanks so much 🙏 💓

[@christianmccollum1028]

Awesome information. Thank you, sir.

[@frankdaiii6403]

AWESOME VIDEO. ESPECIALLY the part about holding back the pivot arm! mine worked great except it's not shifting past the mid points and stays locked after 40mph or so at 3000+ rpm. Now it's giving me a P-1778 instead of P-1777. Mechanical is not responding. I think it's the brand of step motor but i'm gonna double check all the DTC parameters first.

[@JonathanRivera-x3f]

Hola mi carro nissan sentra no hace los cambios

[@islandbeaches395]

Good job

[@animerickoso]

Nice video man! Thank you

[@maker215]

I replied my step motor. But im still having problems. Should i have it reset for it to work?

[@hawkvizion]

MIKEY MAKER check your speed sensor as well

[@arturoalba3865]

@@hawkvizion which of the two sensors

[@WizzRacing]

@@arturoalba3865 Change them both... They only cost about $30.00 each on E Bay for Nissan factory ones. As the parts houses want $190.00 for one...And change that round filter in the side of the transmission..Cost about $14.00 for factory one.. Take notice. If you drop that pan and it's full of metal or them links. Just get a used transmission..

[@tipstricks252]

Great video

[@JonathanRivera-x3f]

Pero no me muestra ningún codigo

[@Radicson]

Нихуя не понял но молодец

[@investdoubleyourmoney8930]

It does not work cause not gaining speed you need two change the whole valve body transmission

[@tajhealthnature8570]

Thank you

[@1vaquita]

thanks buddy!!!!!

[@investdoubleyourmoney8930]

You put that pin in the wrong hole

[@splash5974]

Which pin?

[@investdoubleyourmoney8930]

It go on the side were he is saying you cant put your fingers in

[@jamesofalltrades4359]

How many quart of cvt did u put back in?

[@reycaro8545]

James P. Jones V 6 1/2 quarts I didn’t flush the transmission fluid but if you need to flush the transmission fluid completely it will take like 8 to 8 1/2 quarts

[@jamesofalltrades4359]

Rey CaRo thanks bro

[@jamesofalltrades4359]

Did this fix your issue with the transmission. Bc I have p1778 too and I’m about to change mine

[@christianmccollum1028]

The boy's Altima displayed the code today for the first time. It's still driving fine but I see me having to replace his stepper motor real soon myself.

[@Patron-hk6be]

rey caro i did the same to my 08 altima 2.5 and followed the the steps and it didn't work what you recomend

[@sr.brobennett2473]

What's the parts number

[@richardkuhn4358]

GOOD JOB

[@bestofthebest3821]

30 transaxle shop owners hate this video

[@bigkam5302]

😍😍

[@عبدهجادجاد-ح3خ]

حبيبي

[@eliseorosalez7293]

Rong hold

[@user-ju5hz5nb3r]

Great video

[@gottosahani7571]

Good video thanks for sharing ❤