See my video on how to remove these HERE:- kzbin.info/www/bejne/eJuqdqVoq5Kpba8
@OpelpepePower6 ай бұрын
Hi Robert. I have the 1.6 DTL. I avoided this build-up by removing the oil gases from the camshaft cover to a decanter or oil collection tank and placing a metal gasket at the EGR inlet, in which we reduce the passage of exhaust gases to a hole of only 8 mm in diameter. There is no DTC fault, the engine gains at low revs, and no part of the intake system gets dirty with oil and carbon. If we leave the system AS STANDARD, the sum of oil and carbon will sooner or later clog the EGR, the cooler, the electric air passage butterfly and the MAP sensor as we see in your video. After 9 years and 198,000 km I have hardly any dirt (from time to time) I remove and observe the turbo inlet pipe, the throttle valve inlet, and the MAP sensor and it is almost clean. It is worth it Robert. Greetings
@Roverturbo6 ай бұрын
Is this the b16dte dtl dth engine?
@Roverturbo6 ай бұрын
Hmmm interesting… as it’s blocked the egr cooler twice now. Doesn’t it cause smells under the bonnet to reroute the breather? What pipe exactly?
@stevescet6 ай бұрын
I have the exact same problem on my astra k , bought a 2nd hand cooler to clean then I will swap over the ends . Mines done 90k miles. I did fit a catch can a couple of years ago but took it off. I took the rocker cover to turbo rubber pipe off and rerouted it through the catch can and back to the turbo again. Its doable with alloy fittings and silicone hoses. It does trap a fair bit of water vapour and oil .
@stevescet6 ай бұрын
@OpelpepePower Could you please post a pic of the catch can install as I am interested thanks
@stevewilcox63044 ай бұрын
Can't thank you enough for your video. I filled my egr cooler with dpf cleaner (2 cans with flexible tubes [sealy dpf]) from both ends (throttle body and egr valve), but left it in situ. A nylon pipe brush was used to scrub it out as much as I could. It soaked for an hour. I should have syringed it out but I used kitchen towel instead, although I was careful not to drop any paper back in. The result is the box is as clean as a whistle and the warning light has stayed off since then.
@Nemesisx1974x2 ай бұрын
Well i did it .I have taken of the cooler .mine was Completely blocked up.i used egr cleaner to Soften up the carbon deposits. then i used a jet wash and pulse the jet wash so it remove the carbon deposits..And it worked .went for a drive on the motorway got home no Codes .Grate work Roverturbo
@Roverturbo2 ай бұрын
Thanks.
@toshtwentythree195Ай бұрын
thank you
@helpmediy63544 ай бұрын
Hi, Thank you for your video. How easy/hard is it do remove the egr cooler? Can you please make a short video explaining what needs to come off and which bolts to undo? Is it all accessible from the top? Kindest regards
@Roverturbo4 ай бұрын
It’s coming…..
@Roverturbo4 ай бұрын
kzbin.info/www/bejne/eJuqdqVoq5Kpba8
@Nemesisx1974x3 ай бұрын
May i ask did you get a new EGR cooler gasket for both ends if the cooler and were did you Get it if you did ?
@Roverturbo3 ай бұрын
I said in the video, I used silicone and the old gaskets. I’ve done this a few times.
@Roverturbo3 ай бұрын
In the other video that is….😏
@Nemesisx1974x3 ай бұрын
Yes i saw that but i was hoping you looked for one .i want to do it the correct way thats all @Roverturbo
@MrDufftastic6 ай бұрын
Hi Robert. Thanks for posting this. I have an Astra K with 98000 miles that occasionally flags a P0401 code. I clear the code and it stays away for some time but I will need to to something more than cleaning the MAP sensor periodically. As you have shown I too think the culprit is the EGR cooler and a good clean is probably on the horizon! Does this job require any specific tooling, is there anything to watch out for, new seals etc or any recommend removal steps? Any pointers gratefully received.
@Roverturbo6 ай бұрын
No special tools, fairly easy, just time consuming. I put mine in a tub of pure tfr for days, periodically removing flushing through and compressed air, then back in. I had a spare, so took my time.
@Nemesisx1974x3 ай бұрын
just thinking what about the pierburg egr valve if that's playing up can that give you the code
@Roverturbo3 ай бұрын
A faulty egr would normally bring up a egr valve code. Not a flow code.
@Nemesisx1974x3 ай бұрын
@@Roverturbo I'm getting sick of it i don't want to touch my car no more .
@Nemesisx1974x3 ай бұрын
@@Roverturbo PO401-00 IM GETTING SAME CODE .
@Roverturbo3 ай бұрын
Clean or replace the egr cooler then.
@Nemesisx1974x3 ай бұрын
@@Roverturbo yes it seems i will have to clean it :(
@Nemesisx1974x3 ай бұрын
I'm getting Electrical failure P0401 EGR System Flow Insufficient i did the egr still getting the err . but some times i get a spanner .
@Николай-к3о4х11 күн бұрын
Guten Tag, sagen Sie mir vor dem Reinigen, haben Sie es vollständig zerlegt?
@Roverturbo11 күн бұрын
To completely clean yes, see my other video.
@BurtonsBeatz5 ай бұрын
Hi, can you give me a guide on how to remove this thank uou
@Roverturbo5 ай бұрын
I’ll try.
@Roverturbo4 ай бұрын
kzbin.info/www/bejne/eJuqdqVoq5Kpba8
@guywilloughby33835 ай бұрын
I'm having exactly the same problem and I am also having a problem with constant regeneration on the DPF!! These engines are terrible in my opinion I've had nothing but problems with mine!! Euro6 engines seem to be far mare problematic than euro5
@Roverturbo5 ай бұрын
Get your dpf cleaned. Once they are blocked to a certain extent, they will never clean themselves.