Part 1 - How to Rebuild a Cummins 12 Valve 5.9L Diesel Engine

[@throwaway692]

Dude.... you are a god among men. I'm starting through the series again for the 2nd time. Thank you. :)

[@BeADad2447]

Awesome video!

[@بنقريش-ث7ص]

انا سعيد لان نكتشف قناتك شكرا على تقديم هذا المحتوى الجيد

[@munangwaherbet5434]

Can injector nozzle course a knocking sound

[@0rrin]

What size Flex-Hone did you use and what's the grit number?

[@kleinbiker1]

Old video but what was the mileage on this motor when disassembled?

[@watermalanblew]

How do you lock the ve pump in time when disassembled?

[@minixg4857]

I can see a big mark on that #1 rod journal. Was that just lighting reflection?? Or was it a big divit?

[@Hawk2Kutt]

What’s the handle called at 2:46 ?

[@Captain_Kendo]

Hey I was wondering if you know the difference between the 6bt and 5.9L L6?

[@onemanoperation5459]

Awesome job all around Quick question; what would you recommend to use in case of not having the parts washer available? Also, do you use any product to clean the block and parts? Thank for your time sir!

[@p4_nz]

Thanks for the video. Dunno why, but those dingleberry brush hones always scare the cap out of me. Nevertheless, that's a good tool that provides decent results with a bit of practice. Some even give plateau finish, wich is preferable. I'd run a bore gage to be sure, but your cylinders looked really mint. In the end you mentioned that honing breaks the glaze and gives the ring fresh material to seat and wear on. I'd say that main purpose of honing is oil retention, and plateau hone lets the rings work without breaking in. I understand that you work alone, and I'm a loner myself when it comes to automotive work, but you really should've provided constant oil flow while honing.

[@randysingh7057]

hey sup gm can I get d complete specs for d engine plz

[@jaket418]

How many miles were on this engine when you rebuilt it?

[@diyoregonnowtexas9202]

Great! just got a 1993 6bT 12valve. I want to put it into my Chevy K3500. I'm confused about the wiring. How do I know what wires I need and what I dont? I actually have no idea what all these numerous wires are for. It's a little crazy!

[@wyattburns6436]

I know this video is old..but any idea how many miles this engine had before dismantle

[@claudioc6502]

Muito.bom.seus.videos.do.motor.cummins.bt.me.ajudou.muito.forte.abraco.

[@kaisersoasa]

How many miles on this engine. My 97 been sitting for 15yrs 180k

[@jonassal2676]

what clearance should the main bearing have and piston to wall?

[@CUTTERUPROB]

If your still looking for this info, main bearing oil clearance should be .0015-.0020 and the piston to wall clearance should be .005

[@HikeOntario]

Very enjoyable! Thank you!

[@onemanoperation5459]

Which sand paper grit did you use to clean the blocks surface? Thanks for posting these awesome instructional videos. They help immensely!

[@Jonesys]

120 grit

[@ZHPBrent]

What hone size are you using?

[@mechnicrawat2120]

Plz sir tell me torque for isl 8.9 l enginr

[@JohnDoe-jl3em]

Please tell me that "scrapping" that dodge was taking it to a junkyard to be parted out. Parts are getting so hard to find for the dodge diesels everyone just pulls the beautiful motors out and kills the truck.

[@TheShackHome]

Man am i glad i found this channel. My 72 Chevy C20 3/4 ton PU died about a month and a half ago was wanting to do a LS swap but really wanted to go Diesel but they were too big and too much money. Till i found this Cummins 6BT and this is the engine i want. I don't need a monster engine but want some torque when i do pull a trailer, or possibly a 5th wheel, but also want a dependable truck for daily driving. This fits my needs to a tee. I had an 87 Peterbilt with a 3406 mechanical Cat dont know too much Cummins and watched this wonder where are the sleeves. This help a lot, the 3 vids, so now im ready to get the engine and get started. I'm going for a 400 hp and had a question as the trans. what would you recommend. I'm looking at an a Allision 1000 5 speed but not sure it will hold up or with minor upgrades will it be OK. I'll have more questions as i go but glad i found this for now. I have a 10K budget but hope i can get away with 8K

[@anthonymaynard9809]

You ever end up cummins swapping it

[@dieseldrift8784]

I have a question. Are the pistons in first gen 12v Cummins the same as the second gen 12v’s?

[@jesseherrmann893]

I am currently rebuilding the same engine in my 91 dodge and was wondering how to properly time the injection pump. I have the cam gear at top dead center and timed with the crank shaft and was wondering do you loosen the gold colored bolt and remove the tab then tighten the bolt back down like a set screw or do you remove the bolt and tab completely?

[@АНГАР190]

а в цилиндре эллипс, кольца не будут корректно работать

[@calel5196]

What manuals did you use to rebuild this? I cant find anything

[@frankbertola5466]

like your metholodical process you ain't a waitster very professional

[@jaredmayer3960]

#6 cylinder gets beat the worst because it’s furthest from the water pump and it runs the hottest ring/cylinder wall temps. Usually removing the rear soft plug and seeing the antifreeze sludge shows how much shit is in your cooling system.

[@Bbgptak]

What engine stand do u have

[@javierlahera5239]

hey great video what size hone is that I'm also doing a 12v

[@storminnormansgunworks824]

Did yall get that mildew off the headliner? I recall yall are reusing the seats but I dont recall yall redoing the moldy headliner? Mold is mucho no bueno to inhale. I thought yall would've replaced the entire interior instead of "reusing" the moldy seats.

[@Jonesys]

It is all cleaned up and looking like new! Everything was cleaned and sterilized with an ozonator. Thanks for the question.

[@jerrymarshall2095]

People been breathin mold for 8000 years.it stinks ,but to me it up there with gluten and other crap ,they've invented problems that don't exist for 99% of the population.

[@jonassal2676]

I dont think #6 cylinder has issues because of oil. I think because if the exhaust manifold doesnt let it breathe properly. The manifold is uneven.

[@markriley141]

Moving to a P pump?

[@Jonesys]

Nope staying with the VE pump

[@junalfred2606]

is 6bt has sleeves in it?

[@rickmosholder4593]

No.

[@JohnDoe-jl3em]

RIP to the dodge that this got taken out of, 07.

[@NURGLESBLESSING]

really couldve done without the porno music

[@throwaway692]

Dude.... you are a god among men. I'm starting through the series again for the 2nd time. Thank you. :)