The Heavy Machinery Gear Broken Was Very Professionally Repair by Genious Mechanic… #heavy#machinery#gear#broken#very #professionally#repair#genious#mechanic#pkdiscoveringtechnology
Пікірлер: 31
@alexhaplau-colan541419 күн бұрын
This is actually funny! He's got two pieces of junk and ends up having another one!
@youtubeuser505220 күн бұрын
Everything about the complete job is wrong. No preheat, on cast will make it even more brittle, not veed properly, pieces not aligned properly, as can be seen by the amount of machining done to make it look flat, so gears will not be aligned and will clash and break on first rotation, not aligned in chuck properly, seen by how bad an intermittent cut was made and the amount of machining again to make it look flat, gear cut terrible, will cause a terrible knock in application, it’s been undersized in its width so will need to be spaced to fit, so unless this is driven extremely slow and have absolutely no load on it, it will likely not last more than a few seconds
@jonbender911015 күн бұрын
It may be cast iron, but the sparks from the grinder looked more like steel. Could it be cast steel ?
@youtubeuser505214 күн бұрын
@@jonbender9110 it’s hard to tell when they don’t give a clear view of the material and the video is sped up. It does look like porous cast when he puts it in the vice just before grinding, obviously the piece has been cut through with a grinder, but the parts where it has been torn apart to simulate breakage look cast. I could be wrong 🤷🏻♂️
@alexhaplau-colan54148 күн бұрын
Why people do this. Let's say the weld is successful, which cannot be, but let's supposed it is. I really want to see how that gearbox box works. Is funny, a gear having two radii, that will be really funny.
@joellosoya709816 күн бұрын
With, his safety glasses 😎 and his safety 🩴 sandals, absolutely 👍 OSHA approved.
@markweaver587216 күн бұрын
😆
@ronanstis632820 күн бұрын
A professional would have covered the bed of the lathe before carrying out the grinding operations, to protect it from abrasive dust.
@RixtronixLAB18 күн бұрын
Creative video, thanks :)
@craigsbully19 күн бұрын
just, Oh My GOD!!
@johnthompson360515 күн бұрын
as a trained gear cutter all I can say is , "ignorance is bliss lol"
@peatmoss441513 күн бұрын
Your channel has no content....
@markweaver587216 күн бұрын
Genius mechanic? NO! A machinist who gets paid what he is worth. He will gladly take your criticism, because he gets paid for having you watch and comment.😄
@MichaelFazio-ys8ly12 күн бұрын
Perhaps had he add 2 dowel pin between the 2 pieces before welding. Well established.
@CMAenergy17 күн бұрын
He faces the sides to hide the poor tolerance needed for gears, which he could not establish with this method
@miguelfdez71217 күн бұрын
At last the sprocket is almost round
@un-factory15 күн бұрын
The repair ability is amazing.🎉🎉🎉🎉🎉
@craigywaigy470318 күн бұрын
I know things are economically tough in 🇵🇰Pakistan at the moment, but gentlemen, this is going from silly to darn right disrespectful😏. That gear was perfectly fine until someone deliberately partially sliced it through with a grinder, before levering it appart to disguise the raking cut. Don't waste the goodwill that you've earned... Fix something that NEEDS fixing eg. Screw jacks, trestles, make a decent drill clamp and Morse Taper chuck for the 🇵🇰🚚Pakistan Truck crew - it could be a multi part upload, which would garner interest and save money for the truck rebuilders(1man instead of 3(chain tensioner, tommy/cheater bar holder & drill operator) to drill large dia holes..... Still gave a 👍up in support, but keep it real PLS!
@FarazKhan-pe8st19 күн бұрын
If I have the only option to repair this broken gear, I will fill the crack with high grade epoxy resin, then sandwich the gear between two face plates and bolt them. Then repair broken teeth by weld filling and machining
@pastorvicrosado72786 күн бұрын
Wear protective gear for eyes and hands.
@jurgendudda659718 күн бұрын
Man kann es auch übertreiben
@kthwkr19 күн бұрын
This must be a low RPM gear. By holding the pieces together there is no assurance that the resulting gear is actually round. It should have been lightly tacked up and rotated on a lathe to check for roundness. Must be really low RPM. Perhaps not even a whole revolution.
@thomasjosejosephjose703619 күн бұрын
It is greed to repair the gear. No good machinist shall spoil his reputation by doing it
@PhuongNguyen-jr4mp15 күн бұрын
Kim loại nguyên khối còn bị gãy làm đôi thì lắp ghép này được mấy giây?
@khuoubinhminh3 күн бұрын
❤❤❤❤❤❤❤❤❤❤❤
@MichaelFazio-ys8ly12 күн бұрын
Hei is cutting the sides to get it balanced,nothing else.
@sams24420 күн бұрын
V groove not enough it will break again not qorth
@pedrojbc200721 күн бұрын
ما شالله،ممتاز
@j.conxcara3814 күн бұрын
no no no no no no no no
@martindaubert163620 күн бұрын
I thought the crack was still visible like a hairline