Plasti Dipping Emblems-The best $5 car mod

[@firehead1221]

Make sure to warm up your cans in warm water and make sure you fully wet out the last few coats if you want to get rid of the textured look you ended up with. It should come out fairly smooth when done right. Definitely a cheap mod worth doing that looks good.

[@kccreations5945]

Good tips! Thanks for that!

[@9Shahrukh9]

what do you mean by "wet out"

[@xxteep]

yea as shah asked, can u elaborate a little more on what u mean by “wet out the last few coats”

[@sxmori]

@@xxteep spraying very close to the surface

[@assemmota]

As advice also, you must do the spraying in quite cold place below 25C. Hot place will spoil the process.

[@NarLyNaRdi]

Pro tip: put a very small piece of tape on paint, in between outside of H and inside of circle around H, so you don’t have to scrape a hole through the plasti dip to start the peel. You can take that piece of tape off, and there is a nice little uncovered spot you can start peeling from

[@kccreations5945]

That is a good idea! Thanks!

[@billychan8631]

I should've done that to the 'O' and 'D' in my Odyssey as well. Alas, I did this last month before your comment

[@TheDacker57]

Yes yes yes

[@vlz.matthew]

just use a toothpick its much easier. if you take the tape off you will have little pieces of plastidip that will be hard to take off without peeling the letters

[@kerrygibbs8198]

This is very cool! Years ago I was hand polishing my chrome emblem. I was trying to make it super shiny. Just by hand, I wore a spot thru the chrome. I had to continue to polish to remove all the chrome. That’s how I discovered blackout emblems. Seriously it did look good.

[@kccreations5945]

That’s awesome! Those old chrome pieces are hard to come by! Glad you liked it!

[@Amizori]

i just did this to my silverado. i didnt want to go buy new black emblems again so i did this. And its been worth it. Even if you have any "over spray" I used some hand santizer to rub it away and then sprayed the spot down with some warm soapy water to ensure the alcohol from the hand sanitizer didnt harm anything

[@suemosher1839]

Pretty cool. This will give the guys and gals a good project to do alone or together while locked up at home for weeks and months. This is a very sharp looking finished product. Thx for letting us watch.

[@mexifry222]

Who's locked at home? Someone call the cops to help them

[@joesmith3908]

I remember driving to work during lockdown. Was a ghost town. Was so strange

[@Turk_2023]

@@joesmith3908 Indiana didnt change everyone just acted as normal lol.... Like at the beginning everyone was a little paranoid but by May everyone was like fuck it the news is obviously lying. But there are a few people who still wear masks, I assume they are criminals.

[@joesmith3908]

@@Turk_2023 some of my coworkers got Covid real bad. Guess the severity was a lie until you were the one with serious respiratory issues. I took precautions as best I could, not having the option to work from home like so many do. I was lucky and didn’t get Covid until last summer.

[@robbarber7253]

@@joesmith3908 It's at the very most bad flu/cold. Everyone one that gets sick nowadays that I know have one thing in common 💉

[@allenplant1702]

I've used plasti-dip for many many projects and this method really surprised me! Very nice results

[@kccreations5945]

It surprised me as well! Glad it came out so nicely. Thanks for the comment and watching!

[@jamesbissonette]

lol what's the other way of doing it?

[@allenplant1702]

@@jamesbissonette peeling the letters off the car and painting them on another surface.

[@jamesbissonette]

@@allenplant1702 ok mate, cheers

[@beezito]

@@jamesbissonette omg its you James

[@TheRealNuri]

I suggest you use clear coat after you've done all of your layers. I did this to my car on the emblems and it came out really clean + it protects the plasti dip

[@theamazinggoldfish8713]

Question please 😁, are you saying to clear coat before doing the peel off from around the letters, or after?

[@TheRealNuri]

@@theamazinggoldfish8713 before

[@theamazinggoldfish8713]

@@TheRealNuri thank you but won't that get over spray on the paint?

[@TheRealNuri]

@@theamazinggoldfish8713 you just spray the clear coat over the plasti dip and it will peel of just like that.

[@theamazinggoldfish8713]

@@TheRealNuri thank you I'll try it. I have an silver car so the black would just Pop unlike the chrome. Thanks again.

[@SidVintageToys]

I did my marker lights, nice tint and still looking good 6 years 65k miles later 👏

[@yamahaao]

why is your profile picture a dog shitting

[@rvh77]

Thanks, bud. I wanted to change the emblems on my F150, but this makes so much more sense. Gonna give this a try.

[@vciq]

Same I’m considering it also !

[@nicksucksatdrawing]

@@vciq Very cool throttle profile picture

[@billychan8631]

Thanks to your vid, I did this to all 3 of my cars. One note, the 'O' and 'D' in Odyssey are a pain to fix if you don't plan ahead and stick a little tab inside for peeling afterwards.

[@weaseltown]

Finally someone that knows to spray paint in a sweeping back and forth motion while stopping at each end. It's unbelievable how many videos there are of spray paying on KZbin where people don't get this extremely basic technique. Hell it even says it on the damn can.

[@shelbyseelbach9568]

No it doesn't.

[@76cnolan]

@@shelbyseelbach9568 so you’ve read EVERY label on EVERY can of paint? Jesus you know it alls are annoying.

[@shelbyseelbach9568]

@@76cnolan That was EXACTLY my thought about the original comment. Funny how you didn't notice that your little comment about "know it alls" ACTUALLY applies to that comment, my confused little buddy. LMFAO. Talk about selective reading comprehension. Jesus, you complete morons are annoying!

[@TheDHJunkie]

@@shelbyseelbach9568 never once in my life have i seen a spray paint can that DOESNT have that written right on the side

[@shelbyseelbach9568]

@@TheDHJunkie Yes you have.

[@kodasanders7208]

Read tons of comments and not a single person here seems like they’ve painted professionally. I watched your video for 5 seconds and can already tell you a HUGE no no that you’ve done before painting. NEVER use cloth that is dingy and falling apart to prep your painting surface. You risk whatever dirt/debris is caught in the strings being left behind on your prepped surface. You also risk leaving behind stray strings/threads that you wouldn’t notice without a thorough inspection. You can see thread caught under the plastidip in the before and after transition photos/videos. Sprayed paint unfortunately magnify whatever is caught underneath and only gets worse upon adding extra coats so it’s VERY crucial nothing stays on the surface and nothing lands on the surface while curing. Outside of that, your technique is great.

[@kccreations5945]

Thanks for the info man! Glad I did some of it right!

[@sxmori]

Microfibre towel?

[@kodasanders7208]

@@sxmori that would probably work but if you’re cheap you can just use like a polyester type cloth. Essentially nothing stringy or falling apart just because a string may be left behind that you may not catch until you’ve sprayed your first layer. Nothing’s worse than picking cotton fiber out of your paint because you’ll almost never get a smooth texture again unless you wipe it down and start from scratch.

[@tysoncolindres5884]

Your plasti dipping plastic emblems on a older civic.This isn’t painting stainless steel emblems on a Lambo! Who cares about the rag or threads on this temporary paint job this shit peels off easily! Start using a mask when you paint the fumes are obv making you brain dead!

[@kodasanders7208]

@tysoncolindres5884 man for someone who replied just to talk smack, you really don't even know the year of this civic he's painting emblems on. Also, why go through the effort of making something look good and not do the best job you can? Sounds like someone's brain dead from fumes and let me tell you, it isn't me. Car is at least a 2016. If you think a 2016, or any car for that matter, shouldn't look good just because of the years it has on it, you obviously aren't someone who appreciates fine detail or truly enjoys preserving their work.

[@Hwan.421]

Just did this to my Toyota. Absolutely wonderful!!!

[@MikeSmith-fq5dv]

How well does it last?

[@Hwan.421]

@@MikeSmith-fq5dv multiple car washes w touch n non touch. Sever thunderstorms etc. very amazing!!!

[@Hwan.421]

If u wanna get rid of it, spray wd40, let set five minutes n it’ll come off w some rubbing

[@ebonyb.7690]

Thank you for the video, I was about to take off the whole emblem and spray them

[@smeg8557]

Finally a video with no BS

[@kccreations5945]

I tried to keep it simple! Thanks for watching and subscribing!

[@cazd5398]

a tooth pick works really well to get clean edges

[@tqsuited]

Nice job, but I would personally debadge the Civic badge and just keep the H emblem in centre blacked out.

[@zesound]

Thank the wife for us on the great camera angles. Thanks for the video!

[@TalkingHands308]

I've always thought those chromed plastic names on cars looked so tacky, making them black like that does make them look a bit better, but I just got the Ford Maverick and I'm glad the name is imprinted in the tailgate instead of just having those plastic letters stuck onto it... Thanks for the video, I'll probably find something to do this with, lol.

[@slick-rides]

Blackout those ugly blue oval Ford emblems. Check out this video. I plan to try this when I get my Maverick... kzbin.info/www/bejne/fp_KgmWpnaaYqM0

[@TalkingHands308]

@@slick-rides I was thinking about that, mainly for that chrome rim around the logo. I personally don't mind the blue Ford emblems. Loved my 2005 F150 with its huge Ford emblem on the tailgate, lol.

[@slick-rides]

@@TalkingHands308 Mine is going to be Carbonized Grey, so think the blacked out Ford oval will look better.

[@TalkingHands308]

@@slick-rides Mine is also carbonized grey. I'm sure it'll look better, I just personally don't mind the logo showing in its original colors.

[@frederickfrantz9996]

Too cool. I have to try this method. Thanks for sharing. 😉

[@kccreations5945]

It’s pretty awesome I was amazed at how well it works! Enjoy!!

[@moealmak9666]

Nice job! How long does plasti dip last? Can i use it on the windows chrome trim ? And last how about spraying clear coat on the top before peeling , brand new car i really wanna do it right thanks in advance.

[@hairybizrat2078]

I did my front and rear emblems red to match my skirt pinstripping. It was so easy and was done in an hour

[@kccreations5945]

I bet that looks great! Glad it worked for you!

[@Ck-jh7xp]

how an hour, at least 20 minutes between coats, with at least 4 or more coats, maybe 2 hours min,

[@micharel937]

@@Ck-jh7xp shut up

[@goodcitizen3910]

Do I absolutely need a garage to do this cuz I don’t have one

[@franchisefred4066]

@@Ck-jh7xp You don’t need 30 minutes between coats moron. 10 mins max only 😂

[@brendanmcgrath8282]

Oh wow. I thought I was the only one. I black plasti dipped my rear emblems and white on the front. Looks really good. White Accord Coupe 2014.

[@kccreations5945]

Ooh white on the front?! That’s interesting I’d like to see that! If you want send me a pic to my email [e-mail]

[@LuckyCharms777]

1980s Eurolook with that white on white I’ve always liked that monochrome style 👍

[@Tyler77573]

The plasti dip sticks to the plastic lettering and emblems better than it does to the clear coat over the paint, just be careful, it can peel from the emblems too

[@olopatadine1052]

how do i make sure i dont end up peeling it from the letters

[@11bravo80]

​@@olopatadine1052call this guy he'll come to your house and do it

[@donaldredline975]

Next to the DYC videos, this is one of the best.

[@kccreations5945]

@@donaldredline975 thanks so much! Not sure who DYC is but I appreciate it! Lol

[@DarkSithLord18]

Just did this on my 2008 mustang GT and it looks great, thanks for the video my friend

[@static_Tricolor_camry]

It's not enough coating, I usually do 7 coats until the emblemings are totally covered. The problem with plastic dip is they start to peel overtime, you're better off just buying a can of Black paint and spray painting the emblemings but you'll have to remove them to do that.

[@ukelelestings1931]

yea because it's such a hard process to redo 😂🙃 i don't really think this man cares lol

[@vlz.matthew]

painting is such a difficult process you have to take the emblem off, and if you get overspray its very difficult to remove

[@metaldreams3595]

new guys, notice how he starts to spray a few inches outside of the emblem. Thats to get the spray going so itll be consistent

[@L1nkgray]

Honda wanted 110$ for blackout badges. This is definitely the way to go.

[@N3wbMa5t3r]

Go on eBay... They're like $20

[@shasboom5807]

Thanks for the vid! Commenting for the algorithm.

[@kccreations5945]

Not All Heroes Wear Capes! lol Thanks so much!

[@BillsCamperTruck]

I won’t be doing this, but smartest way to do this I’ve seen

[@kccreations5945]

Thanks!

[@TheGjkddk]

Man the previous owner of my car did this and when I removed the badges I could see where he ran the razer through smh. Don’t use to much pressure guys (obviously). Or just try to cover as much area as you can with the tape before you spray (put tape between letters, inside the letters, around the letters, etc..) so that you won’t have to use the razor.

[@charleysanti]

What razor? Lol

[@NarLyNaRdi]

Toothpicks are your friend

[@TheMasterMaster789]

Did this on my civic and it went perfect! Thanks!

[@randolfhearst9343]

Body shop tip put newspaper on hood. Tape edge remove it from the hood and place where you want it.

[@shakeyrecords3284]

Another easy way to get the plasti out of the holes of the badge is to use a toothpick

[@kccreations5945]

I thought I showed that in the video because I definitely used that method! Thanks for the comment!

[@recordslave]

Put a small bit of painters tape in the little spaces before you spray, this way you can pull the plasti dip up real easy with your toothpick ;)

[@kccreations5945]

@@recordslave genius! Where were you 3 years ago??? Lol

[@tonymante8759]

dont ever use rubbing alcohol on your car it eats the clear coat which will eventually lead to rust over the years from exposed painted metal with no clear coat protecting it. water and soap followed by a water rinse off and than microfiber dry off is all you need.

[@kccreations5945]

Sounds good thanks!

[@franchisefred4066]

FACTS

[@mygt8a4re]

70% or more diluted will not harm your clear coat in an instance like this. 90% can harm it if overused. It will wear it down a bit but it takes a lot to wear through and expose the paint. I personally get 90% and dilute it 50/50 with water for automotive use.

[@phtevenbrad8387]

I didn’t use any…woops

[@adrianopapa1798]

Muito bom amigo, é o melhor vídeo explicando de forma didática. Obrigado! 🇧🇷

[@AustinDashes]

I bought a Ford cmax hybrid and I'm amused, the last owner Plasti dipped the emblems on the back and the wheels. The paint is black and so are the wheels and the emblems and the interior 😂 surprised they didn't tint the windows.

[@JohnPMiller]

I used Plasti Dip to make my shiny white security cameras matte black. It's good stuff.

[@cm1133]

I’m dead! Thanks for the laugh.

[@GKUZYK1]

How is it possible for the plastic dip to not peel off the letters and only come off the painted surface.

[@11855alan]

My thoughts exactly!

[@theheartlandgroup757]

Because the lettering is raised.

[@stevealexR1]

@@theheartlandgroup757 But the paint was going from the car’s bodywork to model letters in one continuous film so I also don’t understand why it comes away so easily!

[@rrraynoorrr]

Maybe because he sprayed from all directions, which allowed the dip to get under the emblems a bit and when he pulled, the plastic simply gave away to the sharpness of the underside of the emblem (he was pulling up after all). Not sure if that makes any sense.

[@TBJYT]

He cleaned the letters with alcohol so the plasti dip adhered to the letters properly so it’s an easy peel off on the paint

[@paliacho9]

But how does it stay on the letters, even around the edges, and not peel off? Do you apply something to the letters and not the paint? Or vice versa? How do3s i5 not peel off the letters? Or do you use an exact knife and outline every letter?

[@AK-gb9rp]

it's plastidip not paint. the emblems arent painted. the car is. plastidip wont stick to paint but it will to the emblems

[@BobbyC777x]

@@AK-gb9rp Thanks - I had this exact same question!

[@RobertPaulson87]

How long will this last usually? I'm assuming it'll wear off quite quickly if you wash your car often?

[@sawman1600]

I live where roads are salted for winter and constantly wash my car with two bucket method and pressure washer. My emblems look as good as they did 3 years ago when I plasti-dipped them. I imagine getting too close with a pressure washer would remove the coating but with a little common sense plasti-dip can actually hold up for a very long time.

[@angieanderson162]

Mine did not pull away like that. It acted more like regular paint. Had to use a plast tip to get the access off. Scratch part of the car. However I used a different brand this time.

[@exploregon4444]

Just finished on my Tacoma!! Only ones I had to do were the TACOMA badges on my front doors....chrome....ICKY. Followed your recipe & WABAMM!! Thanks man!!

[@kccreations5945]

So glad it worked for you!! I did it on my Tundra about a year ago and it’s holding up great!

[@FacelessMachine]

Just got the 2022 Tacoma and this is my project tomorrow. I got the "attitude black" paint, so I'm going to use the bright red plasti dip. Great video!!!

[@exploregon4444]

@@FacelessMachine Sounds like it'll be beautiful!!

[@FacelessMachine]

Awww thanks! I'm so hoping it will. 🥰

[@tibbittsaerospace201]

this is the most honda civic mod ever i love it

[@kccreations5945]

Hahaha Amen!

[@BB-sw8hq]

You should do this to all civics after putting on a 50lbs rear wing so it goes faster

[@kccreations5945]

And adding stickers for more horse power!

[@gamerglicther24]

So the plastidip will just pull of without coming off the letters?

[@michaelscottland4239]

Best window tinting idea 💡!!! Thanks 🙏

[@bradleysmith3121]

Can you plasti dip the emblem on the steering wheel airbag cover without harming the cover finish? 2020 Honda Fit

[@TheHopetown]

Sure go for it!

[@luvluv8929]

Do the dash board while you at it 😆🤣

[@UnexpectedTraveler.]

How good is it when it comes down to washing your car, does it last long?

[@searcher3x]

You should get about 3-5 years from 4 coats. If you do more coats you'll get more time on it.

[@1StinkyFinger]

Looked better before!

[@temtongu9481]

@@searcher3x what if you use a self wash that has high pressure

[@searcher3x]

@@temtongu9481 It lasts a good 5-10 years depending on prep. I've had great success with it. I've done a whole car and recently did my gas cap on my challenger. I've used other products but honestly plasti dip is the most durable, when prepped right.

[@s3ptmbr]

Wondering if putting a masking tape over the logo and squeeging out the emblem and cutting out would be cleaner / faster end result

[@kevinmendoza7581]

Looks great, going to try this on my civic 😄

[@r.mdaniel-sorin]

if I haven't finished all the spray, it can be used again

[@Rjhorning]

Wow, that looks cool man. I didn't realize using that stuff was so easy.

[@kccreations5945]

Yeah me either! Hope it helps you out man!

[@z.k2910]

Nice job. Only small comment is that u use very thick layers en keeping the can somehwat to close to the emblems. Thinner layers would be much better. And keep peeling away from the letters instead of towards it.

[@ZombieAlpaca]

With plastidip you want a light first coat, followed by 3-4 heavy, overlapping coats. It creates a smoother finish. This stuff isn't paint, it also helps to soak the can/cans in warm water for around 10 minutes beforehand for an even smoother finished product.

[@PhrozenPhlanges]

@@ZombieAlpaca I found doing several light coats, 7 actually, worked particularly well on 2 plastic forward facing parts on 1 of my motorbikes, its been years now since they were sprayed and its still the same as the day I sprayed them, nice light overlapping coats 30 mins apart

[@stephenlacher587]

Great way to make your car unique, make everything BLACK. Novel!

[@kccreations5945]

Thanks man! I love it!

[@MikeSmith-fq5dv]

How well does plastidip last?

[@franchisefred4066]

10+ years depending on weather conditions

[@VlogsFromThe6]

lets go! best video on youtube for this man deserve a sub! keep it going

[@kccreations5945]

My Man! Thanks so much!

[@cm1133]

This mod reminds me of peeling skin after a nasty sunburn :-).

[@kccreations5945]

Hahaha that’s great!

[@arunpaul5364]

🙋‍♂️ loved the work. I have a few questions ??? Are all the four coatings 30 mins spaced? Is it just the plastidip can needed to do this or do i need to buy primer or anything?

[@kccreations5945]

Yes every coat was spaced out at least that amount of time, or until dry. And only the plasti dip was used. only other product was alcohol to clean the letters first!

[@terrygerhart1485]

Awesome project, also good comment helpful tips.

[@Tomarsnback.]

Get yourself a cheap bottle of wax and grease remover, its going to be much better than alcohol and you can use it for everything.

[@TeamFish15]

Newby question. How does the Plastidip know not to peel off the emblem?

[@Ivan-jp1dj]

How'd you peel that off without peeling the one on the letters itself?

[@PBrooksSawyer]

Yea I don't get this. Was there a cut scene somewhere where he used a razor blade?

[@RobertBrockwell]

What makes it not peel off the letters when you are finished and peeling off excess dip? Great video by the way.

[@Watchme.copyme.7857]

The break from the letters to the car

[@11855alan]

@@Watchme.copyme.7857 That was my question too! Peeling off the painted area, why didn’t it come off the letters too. Thanks

[@OsoCaliforniano]

Wow man you saved me so much work 😅

[@Spiritualbarbie222]

Doing this tomorrow on my day off!!!

[@JahGotWings]

😂 Same!

[@dennyross5602]

All I really care about is the dog you can hear walking around in the background 😂

[@angelosilva6924]

Thats an amazing video. My problem is that i want paint a color by each letter which i needed to buy 4 spray 😅

[@niacal4nia]

You should use some lubricant around the lettering

[@iamjonbeamer9632]

How long will this last before having to reapply? And if it starts to peel, I assume you'd need to fully remove the first attempt before you're able to reapply in the future?

[@parkerhawley6961]

I did this on my Santa Fe and it lasted no peels winter/summer seasons for 3 years. I’ve since sold the car and the new owners loved the look and said they were going to keep it like that, I just got a civic and will be doing it now on it

[@hawaiifv0]

Damn wish I would of seen this 6 tries ago! You made it look so easy imma redo mine so 7th times a charm lol

[@kccreations5945]

Hope it works out for you man!!

[@omarabbasi2682]

How u mess up 6 times bruh

[@nazarmakhmud1188]

Nice mod, thank you! Greetings from Siberia, Russia =)

[@jamesbrooks6636]

Other people say to add/mix products do/should I need to? I know you only used the spray but does it help or hurt paint less when mixing somthing with it?

[@shadowsidesoamplified]

How come it doesn’t peel or the letters if they’re all shiny surfaces and it’s all one layer

[@shoobidyboop8634]

I find coating the rest of the car in a high quality butter helps the borders to release easily. REAL butter, NOT margarine. Gaw.

[@stevegarcia9553]

How long does this last?

[@GloryBeToGodForever]

Turned out pretty good. Our talents come from our Lord *Jesus Christ.*

[@Hondaddy]

Just wrap it ? Less orange peel look and as a glossy Premium look.

[@jonawilk]

Takes a lot longer and is definitely trickier for people that haven’t wrapped before

[@aldo.z3485]

Even if u have experience wrapping emblems is a PITA lol

[@justinchapman1967]

Why does the plasti dip separate when peeling back? From painted surface to letter emblems, is it not still a solid application? How is the finish so clean without any cutting??

[@TheMaineiacguy]

Good video man! Just did my Jeep a couple weeks ago and I'm super happy with this stuff.

[@kccreations5945]

Yeah it has lasted a lot longer than I expected! Thanks for watching man!

[@haleymariefoster]

@@kccreations5945 how long do you think it usually lasts??

[@kccreations5945]

@@haleymariefoster Mine has been on my truck for over a year now and it looks the same as it did when I put it on! And I get multiple car washes each week

[@handee_maam]

Nice!! How does the plasti dip not come off of the letters?

[@snoochybooch]

I guess because the letters aren't flush to the car

[@captainbanks31]

Magic

[@indiabuckley7411]

Great video! Did you use pure rubbing alcohol or dilute it with water to clean the areas/what ratio if so? Did you use 70% or 90% isopropyl alcohol?

[@kccreations5945]

I don’t remember but I believe it was isopropyl, not sure of the percentage. Really just clean it with anything and let it dry first!

[@HereWeGoMel]

Is plasti dip durable? If it comes off the body of the car so easily, will it come off the emblems/logos just as easily? Like will it be durable in car washes? Or is this something that has to be done periodically?

[@kccreations5945]

It’s not a permanent solution but I’ve had mine on my truck for at least 6 months now and go through the car wash at least twice a week and it looks the same as it did! Just make sure to Do 4-5 coats!

[@fishface6247]

Some people plastidip their entire car and say it lasts 2-3 years

[@jetmechanic100]

How much horsepower does this add?

[@user-ur8ux7yl5w]

40hp

[@ElMachucaPapas]

Great👍🏻. How much this plastidip long last on the emblem with the color without fade off?? I want to try it.

[@dannygonzales2514]

If you ceramic coat the surface it can last for years

[@LSnium]

I think this would easily peel off dont you think? Like peeling around what you did. Might do it to my Toyota Celsior.

[@dailytuning]

Painted it too, very pleased

[@familiecoch]

Nice work! What is the name of the sound track ?😅

[@Rusties844]

Who has done this. How does it hold up too washing the car. Like drive in car washes. Or jet washers but obviously not going too close too coated area with pressure washer. Thanks

[@mamos187]

Does it stay on after washing your car? Or does it peel off?

[@bigd7072]

Did it on my Tahoe, did about 4 coats. It's stayed on for about 2 and a half years now with no chips or anything. It'll hold even with washing

[@ラブユー-n8y]

@@bigd7072 Did you use any plasti dip glossifier by any chance or just the spray?

[@bigd7072]

@@ラブユー-n8y no I did not, that is an option though if you want a more glossy look instead of a matte black

[@ラブユー-n8y]

@@bigd7072 okay, thanks for the reply!

[@HEROFOREVER]

My plasti dip cost 17$ autozone. Still I love how it turned out on my Cruze

[@colincarrington4629]

7$ at walmart bro

[@beautybywendy9174]

Did they have a variety of colors for the spray plasti stuff? I’m really wanting to do baby pink on my black civic hatchback.

[@kccreations5945]

Yes tons of colors!!

[@fred_b_360]

Cheap, easy, and worth it every time🤙🏾

[@johnmangus8015]

I want to try this on my BMW 135i. I think I might try it on my Chebrolet Spark first though. Lol!

[@chemieng]

how long do they last after applying the paint? does it change color or get affected by UV?

[@christophergilbert519]

I put 4 coats on my truck in March of 2020 and it's peeling. My truck is always outside so if it's garage kept i would think it will last longer

[@chemieng]

@@christophergilbert519 Thank you 😊

[@MegaLester1984]

Too cool but what kind of spray did you use on your car

[@darkice7669]

No clear coat? So flat black? Ill just tape it all off so it looks better with clear coat but nice video

[@ducebigalow8834]

If you wanted to spray a clear coat of plasti dip over the black to give a high gloss would you do it after you have peeled the black or before?

[@kccreations5945]

Probably before you’ve peeled it since you have a newspaper covering it and it won’t get on your car!

[@rjunai]

nice job