Taking apart the artemis pp700sa. Note Huma regulator is now set to 100 bar.
Пікірлер: 79
@v6pulsar4 ай бұрын
Excellent tutorial. Thanks for showing us how.
@jakehamilton9352Ай бұрын
This was invaluable...thank you! 👍👍👍
@TheOneLifeRider10 ай бұрын
Those little fingers playing with the ruler... All the best to your little helper!
@philkennedy3423 жыл бұрын
Nice strip down vid Cheers for sharing 👍👍👍
@paulandrews37853 жыл бұрын
Good video on how to strip pp700 cheers 👍
@TheFender263 жыл бұрын
Great video! Best air pistol iv ever owned
@longyx3215 ай бұрын
These pistols are brilliant... So tuneable..
@vihreelinja47433 ай бұрын
To make the barrel "thread insert" to stop spinning. Remove the screw from the rear sight and insert a longer screw. That screw will bottom out against the outer threaded part in the breach of the barrel and will stop it from rotating when mounting the barrel. Just bought one of these pistols and it is suprising how accurate and easy to tune this thing is.
@renzoquiroz2076 Жыл бұрын
Muy buena explicacion felicitaciones
@raunovittaniemi8432 жыл бұрын
Jättebra visat.. Har lärt mig en hel del... Nu ska jag kolla på avsnitt två.
@jamesdiamond57257 ай бұрын
those is cool take care all the rats in the backyard
@Dr.Gunsmith2 жыл бұрын
Great video well made and good information 🙏
@AffordableAirguns2 жыл бұрын
Such of a great video. Congrats
@Nothingness08925 ай бұрын
Hi Great video but can you make a video about how to lubricate and clean an Artemis pp700sa? It would be very great cause i haven't found anything anywhere about lubricating and cleaning of artemis pp700sa
@generallee4412 жыл бұрын
Good job 👍👌
@gotsteem3 жыл бұрын
Not to create any pressure on ya Micheal but.. How about a re-assembly vid now.. I have all these pieces laying here! ;D
@mtairgunner40443 жыл бұрын
Next time I have it apart I will try and get a video of putting it back together👍
@gotsteem3 жыл бұрын
@@mtairgunner4044 I have this PCP pistol and I really like it. It is currently un-modified and shoots well but I think I'd like to increase it's muzzle velocity. I know I am capable of disassembling the pistol and adding a new Huma regulator and re-assembling but I am a little hesitant.. Once I receive the new regulator, I will go for it.. Great video and thank you brother. Liked and subbed.
@mtairgunner40443 жыл бұрын
@@gotsteem You will do great, it is a great pistol and easy to work on. If you have any questions or need any help just let me know and I'll try my best to help out.
@joelrodrigo5 ай бұрын
Hello, I try to find a replacement for the screw of the regulator 27:27 does anyone know the size of the screw or its specifications for buying a replacement that can fit in, please help me.
@esapuhakka54942 жыл бұрын
New FX have 2 regulators, why not work in this too?
@akseminole Жыл бұрын
The Huma is probably the more precise of the 2 regulators, and in a dual regulator setup, I think the point is to increase the downstream regulators pressure regulation precision.
@svzgditeam591911 ай бұрын
funny many of you call it a moderator, to me that term is too generic, that's why we call it a 'silencer', more specific and clear don't you think?
@mtairgunner404411 ай бұрын
Normally I call it a silencer, but online I call it moderator as some people get upset over it. They say it mixes airguns with powder burners 🤷♂️.
@vihreelinja47433 ай бұрын
@@mtairgunner4044 lol. Why would it matter as both serve the same function.. I have a Silencer from a 222 in my 6.35mm air rifle so should i call a moderator to the site :D "purists" are one of the most annoying people around.
@vnv19726 ай бұрын
Здравствуйте, подскажите где можно приобрести такой регулятор давления
@bojanks3 жыл бұрын
Hi, thanks for video. Where do you buy the stock for pistol? Regards.
@mtairgunner40443 жыл бұрын
airgunarcheryfun.ca is where I got the stock from airgunarcheryfun.ca/artemis-pcp-pistol-pp700sa-carbine-stock/
@sunnesonne6 ай бұрын
So adjusting the regulator and hammer spring should be good enough to increase velocities?
@mtairgunner40446 ай бұрын
Yes, to a point you will see some increase.
@sunnesonne6 ай бұрын
@@mtairgunner4044 I think I should be able to get it to 600-640fps with 16gr by just adjusting screws; is the aftermarket regulator a must for it? Forgot to mention, I was unlucky to buy a Canadian version that someone imported to US, so it’s very slow, gets 460fps with 16gr
@mtairgunner40446 ай бұрын
@sunnesonne The stock regulator is OK, just worth it to upgrade when it goes bad. Being a Canadian version you might not see any increase without drilling the transfer port.
@sunnesonne6 ай бұрын
@@mtairgunner4044 I think it should be 4.4mm hole
@mtairgunner40446 ай бұрын
@sunnesonne I can't remember for positive the size but that does sound about right
@EduardoAReyes2 жыл бұрын
Micheal, great reviews. Do you offer tuning services for the Artemis PP700S-A?
@mtairgunner40442 жыл бұрын
I don't do any tuning service. But if your looking for someone that works on the Artemis I would get ahold of Brian @ www.veradiumair.com/index.html I have talked to him on the phone but never sent anything to him, but he does has a good report on airgun Nation.
@thomaspreischer9582 Жыл бұрын
The Block you hold at 18:30 has a very small grub screw at the bottom. Could you tell me Whats the function of this Little screw?
@mtairgunner4044 Жыл бұрын
It acts a a stop so you can adjust the block to match up with the barrel. If you screw it all the way in when you rotate the block you will see that you can rotate it past the barrel and barrel housing a little bit.
@WaschyNumber12 жыл бұрын
So many parts 😳 I thought it would have less valves ect, that's a lifetime to find out if something brakes. 🤔
@chihocheungcc3 жыл бұрын
Great video, thank you for uploading. I have a question, please can you help me. I have stripped the pistol to replace the o ring. When I fill the pistol again it hold air perfectly as the air gauge when up however, when I pull the hammer back and try to shoot it. No air comes out? The hammer hits the firing pin but no air comes out?
@mtairgunner40443 жыл бұрын
Make sure the air pressure isn't over 20 bar mark. If it's good next I would check and make sure the hammer spring got tighten back down to where it was. Hopefully this helps
@mtairgunner40443 жыл бұрын
Also did you adjust your regulator at all? May have set it to high. To be able to adjust the regulator you will need to drop the pressure in the gun down to almost empty. Make sure there is nothing in the barrel and also point in a safe direction. You will have to take a rubber mallet or Hamer with a block of wood and hit the hammer while it's up against the valve. Start off will soft hits and work up in strength until you start to hear air go out the barrel. Continue this until the air pressure is gone in your air tube. Then adjust the regulator Allen screw counter clockwise to drop the regulator pressure. Hopefully this will help and I have explained it OK. Let us know if it worked or what you have found
@stephenoshea11662 жыл бұрын
@@mtairgunner4044 video is excellent and this reg adjustment info is great too. Q: Is this process of emptying air completely to adjust reg necessary every time to adjust up or down? Q: Also to get max usable power, is there a formula such as fully turn in then back out 'x' rotations so that washers work? Thanks.
@mtairgunner40442 жыл бұрын
@@stephenoshea1166 if you have the stock regulator you don't have to degas to increase the reg pressure. To lower the reg pressure it is safer for the reg to degas and then adjust down.
@mtairgunner40442 жыл бұрын
@@stephenoshea1166 For max power there really isn't a easy formula to get max power. The best way is to increase your hammer spring first a little bit and then shoot over a chronograph. Once you hammer spring is to hard then you would loosen the hammer spring back to where it started at then increase the reg a 1/8 turn. Then you would start adjusting the hammer spring again checking over the chronograph. You will keep doing these until you get the speeds your looking for. There will become a spot where when you increase reg and hammer spring you will not increase fps any more once you get to that spot you will decrease everything just a bit to be right at your max speed, this will make sure your not wasting air for your max fps. Gateway to airguns also has some good writeups about doing this and you can also search airgun Nation and will also find some good info. Hopefully this helps and is not to confusing.
@ragotphilippeh64962 жыл бұрын
Hi bro Great video, very interesting thank you for uploading. My question : I can see that you have a Huma Air regulator. Is it stock or did you install it yourself ?
@mtairgunner40442 жыл бұрын
Thank-you. I installed it myself, they are very easy to install.
@derivas0072 жыл бұрын
@@mtairgunner4044 why you don t remove completely the original regulator disk if you use huma air? i don t understand...you will have more plenum air once it s remove
@stevejohnson17973 жыл бұрын
I have the old type, green handle, looks identicle internals wise. I have resealed it and air seems to be escaping from barrel? Would you have any idia wich seal it could be?
@mtairgunner40443 жыл бұрын
Make sure you have the hammer back when you first fill it, a little pressure on the valve might make it not seat right, that would be the first thing I would check. Did you take your valve apart at all?
@stevejohnson17973 жыл бұрын
@@mtairgunner4044 no did not touch valve. I will strip it this aft to make shure all seals are still good, and try the method u said, pull hammer spring back and gentley fill. Thanks for reply..
@stevejohnson17973 жыл бұрын
@@mtairgunner4044 sorted it mate, one of the main seals on the air tube had failed, and like you say putting hammer back when first charging does help! Thanks mate..
@bojanks3 жыл бұрын
Friend, please, are you sure the washers should normally rest on the brass piston? I think it makes sense if the protruding part of the washer should go towards the brass piston, and not towards the screw. Accidentally when I opened my gun they fell on my floor. I don't know how to return now :(
@bojanks3 жыл бұрын
Yes, I am now pretty sure of the layout of the washers. Look this videos: kzbin.info/www/bejne/Y2STqqWFj8p-Z7c kzbin.info/www/bejne/nYjCcnt4qdB6i7c kzbin.info/www/bejne/jmKUg6Gqfr-no5I
@BlvlWmpower3 жыл бұрын
Can PCP guns blow up of oil gets into the air cylinder in the gun or tank?
@mtairgunner40443 жыл бұрын
It could, thats why when lubing the O'rings you should use a lube that is synthetic grease or oil. I have been using Super Lube O ring silicone lubricant. I do use oil on the outside parts and do a light coat with oil to help prevent rust or corrosion.
@vihreelinja47433 ай бұрын
@@mtairgunner4044 Bad advice here my man. Only use silicone if you do not know for sure. Synthetic oils can DIESEL under pressure.
@Andrew-qn8fu3 жыл бұрын
Did you drill out the transfer port on the block at 18.24? Yours looks like its 4mm or so, mine is only 1.5-2mm at most. I'm only getting around 4ftlbs out of mine. I've tried to tighten the hammer tension to increase power and although it did a bit the hammer wouldn't always engage as I think it was over wound. I've turned it back to 4ftlbs for now. Would it help by drilling the transfer port out a little bit?
@mtairgunner40443 жыл бұрын
I didn't drill out the transfer port, being from krale it was set up as a full power version.
@Andrew-qn8fu3 жыл бұрын
@@mtairgunner4044 I've drilled out the port to 4mm and the power issue is solved. I have another question, is there anyway to adjust the original reg to flatten out the power curve, spike? It starts at 5.6ftlbs but when it gets close to 115 bar it briefly jumps up to 8ftlbs. I can see the adjustment screw in the trigger guard, would turning this help? If so, would i turn this clockwise or anti clockwise.
@mtairgunner40443 жыл бұрын
@@Andrew-qn8fu I think this is because you are down past the regulator setting. You can go down some on the regulator setting to get a few more shots. To decrease the regulator you will go counter clockwise and to increase the regulator is clockwise. It is a good idea to degass the gun before going down with the regulator, as it could cause problems with the regulator. When increasing you do not need to worry about degassing it.
@Andrew-qn8fu3 жыл бұрын
@@mtairgunner4044 would I need I increase or decrease the regulator setting? I currently have the 10 washers in the reg in this order )()()()()( is this ok?
@mtairgunner40443 жыл бұрын
@@Andrew-qn8fu You need to decrease your regulator setting. Your washers are ok in that order.
@derivas0072 жыл бұрын
did you remove the original regulator after huma air installation?
@mtairgunner40442 жыл бұрын
I gutted the stock regulator, the body of the regulator is needed to attach the air tube to the gun.
@derivas0072 жыл бұрын
@@mtairgunner4044 sorry my english is not perfect..if i undertsand you have removed belleville washer and replace everything just after?
@mtairgunner40442 жыл бұрын
@@derivas007 kzbin.info/www/bejne/jpWbc6GDgpmdo9U No problem, I did remove the washer set. This video will show what all I did to the regulator.
@derivas0072 жыл бұрын
@@mtairgunner4044 i have seen all you video but it s still difficult for a french person to undertsand everything :( !on the manual from huma they said to remove only the valvestem..what is this part? do you have a picture to show me? thanks for you help.
@derivas0072 жыл бұрын
@@mtairgunner4044 does it the screw which keep the with parts wh have te remove? i think yes after watching you video but i prefer to be sure
@harriku.14876 ай бұрын
А нагреть до 80 градусов мозгов не хватило? Никогда это не повторяйте.