SAMSUNG UE43RU7172U. TV turns on and off every 10 seconds with no picture on the screen. sound is ok

[@destinywooten1868]

Thank you so much for taking the time to show people how to do this!

[@cruz1118]

Thank you. My 75inch samsung tv was doing the same thing. Thanks to your video it works a lot better. Not 100% but at least it works. I say it's about 90% fixed. At least you saved me from having to buy a TV right now. I will start saving and purchase another TV soon. Thanks again!

[@verniecastillo5134]

Thank you sir, from the philippines,God bless your job.🖒🖒🖒

[@saputraardhi]

So the underlying problem here is a bad panel? If we want to fix this entirely we have to replace the whole panel? or can we just replace the board?

[@albertaver702]

Watching her in Mindanao phillipines. I'm asking sir what number of pins to be placed of tape method sir. Thank you..

[@gazzy5408]

It's really worked!! Thanks for the turorial!! But the only problem is i can see horizontal line on upper screen. Maybe need an adjustment on the black tape i sticked earlier

[@biggig8548]

Hello I'm having the same problem with a 75" tv and can hear the relay clicking on and off. Disconnected the power supply from main board and clicking stopped and have full backlight on. How did you know it was those pins to put the tape over? Thank you!

[@MackoyTechPh]

Always watching you from Riyadh KSA.

[@abrahamvarsulkar3053]

The CKV/ VGH / VGL lines running around the border of the panel short amongst themselves. To remove this shorting we need to block the supply to these lines. The other LVDS cable still carries all the required voltages and signals and the picture becomes normal.

[@fj7550]

I have these same symptoms on my samsung 55ks7000. Identical, but your solution has not worked for me, could it be that I have to cover other pins? Thank you

[@RepairAllTV]

yes it can be as you are saying you can try to be successful

[@fj7550]

@@RepairAllTV Yes, I have tried with other lines and IT´S WORKS!!!!! XD.

[@pixelalino]

Sur quel base on isole certains pistes svp?

[@AaBb-kb8vj]

@@fj7550 what lines did you cover ?

[@vikramn1256]

Same problem facing with Samsung UA43RU7100Kxxl I have coverd 10lines like u show in this video but not working what should I due plz know me sir

[@ΔημήτρηςΚοττάς]

Thank you very much, a little tape and it got fixed omg

[@zovanrista3106]

It works for me..samsung ua43ru7100k...thank a lot master 👍

[@nikkidelfin5899]

A very useful video. Two thumps up. Great....😀

[@MP3930]

fantastic repair very good worker!

[@LittleBeeBecca]

thank you very much ! this video really helped me

[@robwinter3183]

This worked on mine - thank you. Great job!

[@danjudge2225]

How did you know which spot to cover ?

[@lusikrisdianawati4778]

Thanks,from Samarinda indonesia

[@Radiomehanic]

Вы просто волшебник! Это здорово, это круто! Красавчик!

[@marinatoquete2892]

This was so helpful!!!! Thank you very much!

[@tonybennett2303]

How did you know which lines to cover up?

[@sham0684]

Also how do you know which pins to cover.

[@JunPVlog]

Thank you for sharing sir new supporters here

[@mhamadalhaj1427]

Thank you, you are the best it worked for me

[@franciscofurlan4001]

How can we recognice the lines to cover?

[@carlosmunoz7934]

Exactly

[@RixtronixLAB]

Nice video ,thanks :)

[@bigomaso9855]

My LED TV has a problem of switching on and off intermittently. It is also showing vertical lines that appears on the bottom of the screen. This lines would disappear after some time and reappears again. What could be the problem

[@arekusanda3431]

can i just buy and change the panel ribbon instead of putting a tape on it?

[@olivierb9697]

no, the tape is here to remove power that might be lost in the panel, and triggering the reboot. your ribbon cable is already good.

[@sheikhussain7697]

Thank you so much sir God bless you and your family 👪🙏❤

[@mohan4949]

very nice idea ..tq boss

[@electronicartis]

Do you have any explanation in English why this problem occur a lot of these modern television now I see you have to blank off certain piece on the lvds cable any explanation why.

[@abrahamvarsulkar3053]

The CKV/ VGH / VGL lines running around the border of the panel short amongst themselves. To remove this shorting we need to block the supply to these lines. The other LVDS cable still carries all the required voltages and signals and the picture becomes normal.

[@gryg666]

I've stopped restart by masking 2nd pin (counting from left), on top ribbon (looking on motherboard from bottom of TV). It's no longer restarting, I can hear the sound, also when pressing buttons on remote but still no video. I've tried to cover other parts of ribbon, also the another one, but without success. Is is possible that without 2nd pin working, there will be no option to fix it? The TV is QE55Q60RAT

[@paulietec]

I have a QE58Q60TAUXXU with single ribbon, covering pin 35 (from the bottom) no rebooting and sound OK but no picture, yet to try multiple patches.

[@edyheino]

@@paulietec I have same tv and same problem. I can hear sounds and remote is working but no picture

[@Edob_]

@@paulietec did you find any solutions? That is exactly what is happening to me right now

[@paulsheath6424]

@@Edob_ No sorry, tried different boards no improvement. Covering some pins stopped the constant reboot and provided sound. Did get a few vertical lines for some pins. You might get lucky if you get the correct pins and have a degraded picture. I gave up in the end.

[@abdallahelectronic19]

thank you ,i have a problem with this ic tea 1716 in led tv power supply NO POWER, her problem is that it was exposed to high voltage, and I found the main capacitors swollen, I replaced them, but the IC heats up greatly, but it is fine because I removed it and tried it in another card and it worked fine. Where is the problem? Is it in the components surrounding the ic tea 1716? but which pins of ic responsable for overvoltge or which components must be change smd capacitors and resestors or all them.

[@ryanjmarimuthu3445]

I have the exact TV and problem. But if I remove the ribbon.. It still doesn't work..only back light comes on... No picture..so what can I do

[@sdverner231]

What did you do to fix the issue. I'm having the same problem

[@french3529]

Réparation bleuffante et pourtant née viens de l’appliquer sur mon qe55q60rat de Samsung et super cela fonctionne après avoir passé des heures à chercher la panne (échange standar mainboard x2 sur eBay ) au final cela m’a coûté les frais de retour 17 E. Et voilà qu’un simple bout de stoch règle la panne ,je suis content vraiment ,merci pour ce tuto .

[@FabioDiRausoItalia]

Pouvez-vous dire sur quelles broches vous avez mis la bande? J'ai le même problème. (si vous avez une photo)

[@remembergodisalwayswithyou6862]

Nice video thank you so much sir i watching from Morocco 💟

[@ppppooilkl]

THANK YOUUUUUUUUUUUUUUUUUUUUUU ! 😊😊😊😊👍👍👍👍👍👍

[@ricardomoreno6184]

Pero como saber que líneas se deben anular? que referencia se toma para ello? saludos desde el noreste de México

[@jbl-alsobrio2922]

How to remove vertical lines . already display but when power apper a lot vertical fine lines

[@Wsldbrd1]

explain why it works and what the problems (English please )

[@saarike]

Nice repair!

[@bitsnbobs1969]

how do you no where to put tape

[@gorambaye341]

Thank you very much That alright 👍👍👍👍

[@verniecastillo5134]

Sir how many pins when you block the signal?

[@Yoritomo3800]

Watch on the video description , he has written the link to some pictures about how to do it.

[@rudolphalbert2552]

Pl let me know the name of the repaing tool for all led, lcd, crt tvs, schematics and diagrams

[@leanmendoza4493]

How many pin sir and where do you start to block?

[@valderiquelima9764]

I had this doubt as well. What I used a thin piece of paper that covered 3 or 4 contacts. I randomly put it at one side of the flat cable, first in one cable and the TV turned on fine but the screen had some lines blinking and kind of ghost image. Then I removed the paper and put in the other cable, it then worked fine with good image, only two horizontal lines are fixed appearing in the screen, I believe these are the lines which signal comes through the contacts I isolated. It seems like we only need to change the pressure in the connection. Something to investigate further.

[@nadavleor]

I got the same problem in module qe55q60rat is the solution the same? With your video I managed to open the back cove with no problems

[@RepairAllTV]

repairalltv.com/samsung-ue43ru7172u-tv-turns-on-and-off-every-15-seconds/

[@cotto887]

what you did did not fix the problem. the problem is either the t con board or Maine borad. why no trouble shooting ? you trying to cut corners. the easy fix does not always fix

[@jcalzada74]

If I disconnect either one like you did and both flashing..?? Is not the same solution

[@hailyphuc1765]

Thanks you!

[@stevostevic-z9c]

I succeeded, but there is one flashing line. How can I remove it? Thank you

[@IMMRQ2U]

era solo cinta negra? Was that just black tape?

[@sham0684]

What if you just change the cable, will that work?

[@olivierb9697]

no.

[@zabriagore6076]

Hello I just did this to my Samsung 70inc TV but the color is still dark after trying this trick out. One side of the TV the color is darker then the other side what should I do next to check for if you can help. It's on the left side

[@rafeehossain319]

After using his method I am able to turn the tv on. Display and sound works, but the colour on left side of the screen goes from displaying perfect colour to colourless contsantly while watching a video. Does this happen to you too?

[@hamedsow1308]

thank you very my broth

[@aechtabayer5434]

How would ik wich line to cover

[@마리헌터]

양쪽 하나씩 빼고 해봐도 똑같은 증상입니다. 해결 방법있나요??

[@nghinguyenvinh755]

Qúa hay em ơi chúc nhiều sức khoẻ cám ơn

[@liridonmaholli8052]

Pershendetje te une dul me suksese Amo do vija kan dal kaniher po dalin kajher jo

[@cosmostele530]

Merci beaucoup bon courage

[@pixelalino]

Je ne sais pas sur quel base il a isolé certains pistes

[@n0t_fast]

i have same problem but if i disconect ribbon cable it nothing changing, same restarts and blinding red diode

[@edwingomez3274]

how many lines to cover

[@bernardpanganiban2982]

How many pin to cover

[@smithelectro-plumb2994]

Can I replace 55 to 58 main board

[@soontorntamalee8616]

Thanks you

[@tuandang3784]

thanks very good

[@copenje-i1g]

ku e ke dyqanin fizik?

[@pulushettip2283]

ua43mu7000k..Samsung smart led tv..av HDMI all ports not working..standby ..simble ..showing ..on screen

[@roufiwali6642]

very nice

[@crisildaabulencia7923]

Sir what the number of black type

[@obinna6490]

Hi thanks for the Video i tried it and its works but no picture only Sound Tv turns on with a blue screen no picture..what can i do sir😊

[@ramziageely7931]

Same here I tried moving it but still blue hlep😢

[@rashadquandour4727]

excellent

[@aroartlife]

i don't get it, how did he know it was the second one? can somebody help me understand pls. Maybe this will work on mine as well

[@RepairAllTV]

repairalltv.com/samsung-ue43ru7172u-tv-turns-on-and-off-every-15-seconds

[@aroartlife]

@@RepairAllTV Hi :) No i meant the stripes , you connected and disconnected. But honestly it worked. So thank you, but i think i made my tape a little bit too big :( I have to open and see if i can cut some of it. But another question please. Can i just buy a new stipe? or both 2 of them and have it 100 % quality like before? hope you can help me :) :)

[@screweduptexas3718]

How do I know what lines to cover

[@RepairAllTV]

try to cover 4 lines. each time there are 4 lines until you reach the right lines that need to be covered

[@salvatechnics5130]

Exelente bro💯

[@ralphkingsolon6288]

May I ask what pins to cover and what lenght?

[@jojotech4615]

👍👍👍👍

[@joyjoymagallanes4242]

Thanks

[@rafeehossain319]

After following your instructions, I am able to watch tv BUT the image on the left side screen is in black/white and the right side screen has colour. I put the tape on the left ribbon cable.Can you help me? What do you think the problem is? There is a noise coming from the T-CON board from the left side where the left ribbon cable is connected.

[@nikhitarenchi963]

I have the same issue! Were you able to resolve it?

[@rafeehossain319]

@@nikhitarenchi963 First of all u have to accept that it cannot be fixed 100% like they showed in the video. Once I accepted that I was able to adust to the flickering. Now I dont mind it that much. Keep moving the tape left of right until you have the best possible image and then LEAVE IT. After that, play around with the TV picture settings to make the image a little better. I will share my settings with you: picture mode standard, Expert settings: everything full except contract to 50, Sharpness to 16, Tint(G/R): G54 R46, Contrast Enhancer: low, HDR+ mode: unchecked. The others I left as it is, but u might have other preferences like lowering the brightness etc. I am greatfull that the TV turns on. 95% is better than 0%. Replacing parts does not guarantee that if might fix the issue, it might be main board, PSU, T-con, ribbon cable, one of the leds that could be broken and maybe replacing that one might fix it, or you have to replace the whole screen that will cost you a lot of money and still not guaranteed, so then its better to buy a new TV. It took me a while but am finally able to resist the flickering. Hope this helps you ;)

[@nikhitarenchi963]

This helps! Thank you so much!

[@davodporparviz5762]

Very god

[@labrikihamid5377]

Merciiìiìiiì👍👍👍👍👍👍

[@tuandang3784]

thanks .. ok

[@jbl-alsobrio2922]

No caption rnglish pls next put english language so thst i canunderstand what u say but anywY tnx you

[@ryanp4282]

My Samsung the same problem and I tried the same as your idea but it didn’t work

[@RepairAllTV]

kzbin.info/www/bejne/e2fKnKiKhZx_qpI&ab_channel=RepairAllTV

[@elraposoZX]

Before the problem appears again. In my case 1 year before.

[@deanconley5949]

I only speak english I have no idea what he's saying

[@crisildaabulencia7923]

Hi sir same na same tv problem

[@Jusznani]

This worked on mine , but now half of my screen is black and white and the other side is color 😩😩 what should I do ? Do I need to replace the ribbon ?

[@jcalzada74]

You made the tape to big try a thin line or move left or right a little

[@carlopasswords7083]

Record videos its better quality!

[@muratelmas9787]

ne yaptı anlamadım bandı neden cıkardı

[@alasoua1492]

Hello, nice trick. I tried it but was not successful 🥺 found the pin to cover to stop the power cycle, but no picture, leds are on but not picture. Any ideas what it could be knowing the picture displays the tv logo before rebooting when power cycle happening ? Your help would be appreciated 🙏

[@RepairAllTV]

if your tv displays the logo. tv may have some other problem not with the screen. it can be software or mainboard. or try ribbon to cover with fewer lines. or try two ribbons. but not at the same time. try once if you have no success try. then the other ribbon

[@alasoua1492]

@@RepairAllTV thank you for the reply, I will try that

[@surayaibrahim1164]

Hi🏆🏆🏆🏆

[@Loveiseverywhere10]

English would be soooo helpful

[@RepairAllTV]

kzbin.info/www/bejne/e2fKnKiKhZx_qpI&lc=UgyxTivq6BaaZ63ilwJ4AaABAg&ab_channel=RepairAllTV

[@COURTEN__YT]

Dont work bruh

[@smmasum8594]

Apanar phn no dan

[@McGyver0479]

Sei un asso!

[@lucsiscom]

куда положить изоленту?

[@Nevskyj]

9:40 - 9:50 показано как и какие закрыть контакты на нижнем шлейфе...

[@Nevskyj]

4:40 - 5:20 видно что изолента уже была на шлейфе , путём эксперимента сдвига и толщины изоленты был обойдён дефект...

[@belajashark]

Отступить с краю 12 контактов на ширину примерно 8 контактов - в моем случае телек чудесным образом излечился!

[@belajashark]

О, и внезапно, под видео в описании есть ссылка на фото где прямо сфоткано, что он заклеил 10 контактов на 20 от края. А у меня вот чуть по-другому вышло...

[@hailyphuc1765]

Thanks you!