SAMSUNG WASHER WILL NOT SPIN, OUT OF BALANCE FIX. HOW TO REPLACE SHOCKS ON SAMSUNG WASHER

SAMSUNG WASHER WILL NOT SPIN, OUT OF BALANCE FIX. HOW TO REPLACE SHOCKS ON SAMSUNG WASHER
If you have Samsung washer that starts shaking during spin cycle and gets stuck during spic cycle it could be very possible that you have bad shocks that support the drum of your washer. Of course, there could be multiple factors that can cause your wash to shake out of balance and not finish the spin cycle such as: corroded spider arm, worn bearing, stretched springs and more but we were able to fix our just by simply rpelacing the shocks. We demonstrated how easy we were able to replace the shocks that support the drum and in less than 20 minutes our washer was running like brand new again. We will have a video on a different washer coming soon to show you how to replace spider arm and bearing if this is the cause for your washer not to finish the spin cycle.
► Shocks 1 pair ( check part number for your washer): amzn.to/2UZBPEs
► Shocks the other pair ( check part number for your washer): amzn.to/2yDPauH
► Our Website: www.mechaniclifestyle.com/
►►►Our Auto Repair Channel : bit.ly/2a86p9Z
AMAZON ASSOCIATES DISCLOSURE
Honest Product Review is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com
*Disclaimer
We, Honest Product Review, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not Honest Product Review Channel.

[@utopia2112]

LOL! This guy helps me fix my Ford Cmax and now he's trying to help me with my washer!

[@NoSuffix]

Very nice advice! Will try it out to fix my come-and-go dC code issue.

[@moreoflife1112]

my man from the car repair videos has taught me so much!

[@cribbage]

Thank you for the tutorial! Knowing I needed a 13mm ratchet wrench was a life saver. This job would be impossible without it. Also I would recommend a long sleeve shirt to save your arms some cuts to anyone reading this comment in the future.

[@kamilzieba7427]

Thanks for the help, and actually showing the symptoms of what a bad shock on this machine looks like!

[@saint76767676]

So i had this issue and saw this video and got to work. After taking the first one off, i checked it and it seemed to be working fine. So instead of taking the other 3 off, i just undid one bolt and moved the arm in and out. Turns out they were all ok. So now the issue is likely to be the spider arm. Thats going to literally involve taking the machine apart, although i'd rather do that than buy a new machine. A few tips if you plan on changing the shocks. - Wear a long sleeved t-shirt/shirt. You're arm will get butchered reaching in the hole in the bottom is its not big. - You can easily access the rear shocks from the rear panel. - Front and rear shocks may be different. Look for ALL the numbers on the part. Mine had big numbers, and then smaller etched numbers. The smaller numbers were the part numbers.

[@joaquinmontoya562]

thanks for such a good explanation

[@boogaboogaboogaable]

Great video and a great helper! My daughter is my usual helped also.

[@Ed-pv6ke]

Great vid man!

[@vltruane]

Very informative. Thank you.I have the same washer with the same problem. I ordered the shocks.

[@gnhun101]

Did that fix the problem?

[@vltruane]

@@gnhun101 No unfortunately. I replaced the shocks, and the front balance ring, and it still does it, just less. I made sure the machine was level, and I never overfill it with clothes. I think it’s just a design flaw because the older Samsung washers did not have that problem. I noticed the tub on the older models had a front, and rear balance ring in the tub design. These newer models do not have the balance ring in the rear of the tub, only the front. What I did to remedy the problem some was I placed a pillow on each side of the rear of the tub so it won’t hit the sides of washer so much when in use. This is helping a little bit. I got that idea off of a forum from someone else who did the same thing. I’ll probably get rid of it next year.

[@emmacurran7717]

@@vltruane probably the support spider.

[@vltruane]

@@emmacurran7717 Hello, I took it apart when replacing the balance ring, and checked the spider, it’s like new. The bearing is also fine.🤷🏼‍♂️

[@emmacurran7717]

@@vltruane that’s very frustrating! I’m pretty sure mine is the support spider as I found rocks in my filter which I believe is pieces of the spider. I’m hoping it’s not more than one problem. My machine is 9 years old though.

[@wx2833]

Very actionable content; my unit is a top loader with the same problem; at first thought it was a leveling issue; and installed a secondary 3/4" inch plywood subfloor that was level and it improved but did not resolve the problem; I didn't see the shocks and will have to look again; my unit has four support bars with a pivot ball on top and springs on the bottom of the bars; the shocks maybe higher up on the agitator drum; thanks for providing this content; it gave me another item to check. Peace

[@deeweez5049]

HAHAHAHA.... This voice sounded very failure once video started.. this guy does car repair videos tooo!!!!.... OOOOR better yet this guy does Appliance repair videos tooooo.. Good stuff brother. love guys like you!!! A Mans Man!

[@brandongreyling8181]

Hie bro you have channel for Appliances and a channel for volkswagen channel keep it up man

[@ricardoalas743]

You did it fast becouse had some help

[@rj2764]

Is this the guy that fixed my Chevy sonic?!

[@jmp101694]

And my cx-9 🤣🤣

[@jerometruitt2731]

I watch your car videos too!

[@joelguerrero1913]

Awesome you just saved me lot of $$$$

[@martynh5410]

My Samsung is slightly different but it looks similar. Mine is WF350ANP/XAA. There is a parts diagram I found on line and found that front and rear shocks are different part numbers. My washer is shaking like crazy on the spin cycle, so i'm going o try replacing the 4 shocks to see if that fixes it. I will update after the parts are installed. Good video, thanks!

[@martynh5410]

SAUWALEE MALIWAN I did replace all four shock absorbers but the shaking during spin cycle did not improve. After more research, I found that the most likely cause of the issue is the “Spider Arm Assembly”. This is a 3 pronged aluminum casting that is at the rear of the basket and is attached to a shaft that is connected to the motor. I ordered the spider arm, 6 new mounting bolts and a new tub gasket online from appliancepartspros.com. The repair is quite time consuming and requires taking the tub assembly out of the machine. The 6 bolts that hold the spider arm to the basket will be corroded and won’t come out easily and will break, so plan on replacing them. The job takes all day (for me anyway). The good news is that now the machine spins like new and no more shaking! Parts: www.appliancepartspros.com/samsung-assy-flange-shaft-dc97-15491a-ap4458785.html Check this against your model number and good luck! ( that web site also has repair videos)

[@martynh5410]

SAUWALEE MALIWAN Apparently it’s almost always the spider arm. Apparently the shock absorbers are pretty reliable but the aluminum spider arm is a known problem area because it corroded due to “galvanic reaction” between the aluminum and the stainless steel parts combined with the chemicals and heat plus water in the machine. My machine is barely 6 years old and the spider arm was totally trashed and crumbing into pieces. The other items that it could be are the bearings or the balance ring. If you take out the shock absorbers you will be able to tell if they are bad by pulling and pushing on them. There should be about 1” of slack then some good resistance in each direction. Getting these out takes less than 30 minutes and is quite easy. There are KZbin videos that show the process.

[@martynh5410]

SAUWALEE MALIWAN Well good luck! It’s not too tricky to get the spider arm replaced but it is time consuming and there are a lot of steps and parts to remove. If you carefully label every screw and take a few photos I’m sure you can do it and save buying a new washing machine. But yes check the shock absorbers first. The back ones are easiest to remove. Just take off the small back panel (2 Phillips screws) and you will see them. You will need a 13mm socket, extension and ratchet to remove. Sharp metal edges everywhere so gloves are a good idea!

[@emmacurran7717]

@@martynh5410 I’m going to replace my spider arm this weekend. I’m pretty sure that’s my issue as I found “rocks” in my filter and fussed at my family for washing clothes with rocks. lol Wish we luck!

[@martynh5410]

@@emmacurran7717 Almost definitely it’s the spider arm Assy. Make sure to get new bolts (6) to replace the ones that attach the spider to the drum. None of mine would unscrew without breaking them off and it too me a while to remove them!!

[@realbrotherstvgang4683]

Where did you order the shocks from

[@conqueryourself9527]

Mostly it's not the shocks, it's the spider arm that is corroded or cracked. If the vibration has been going on for a year, your front tub assembly will get worned out as the tub is rubbing around it and could soon crack and leak. If you manually spin your tub and it's wobbling as it spins, your spider arm is broken therefore your tub of off-centered. An off-centered tub will create imbalance as it spin and centrifugal force will cause it to vibrated. I replaced the spider arm, bushing and bearings, front tub assembly, and balancer. I already took it all apart might as well replace them. This way the washer will last another 12 years or so.

[@connormcbride8234]

I don’t think there is a spider arm on this appliance

[@Wow_wow1]

@@connormcbride8234 there is

[@robertromero8094]

This some b.s my old washer lasted 10 years this one lasted 3 lol

[@carolrichards1203]

Samsung sucks eggs :(

[@jerometruitt2731]

Samsung makes trash appliances. If it's not a phone or TV don't buy it from Samsung

[@bobbyavila7621]

They look nice but they don't last.

[@howardjohnson4198]

He’s doing it all wrong

[@nichecreator1464]

I have a samsung vrt. Some times the water works then it stops and the machine just makes a weird groaning noise like it's trying. Yeah. If I shut it off and start the clean cycle the water pours fine until it gets to a certain point and it just starts making noise again with no water. It can do that 4 hours without any error codes. Do you have any advice please.

[@danielbailey848]

Could be a clogged/ defective fill valve.

[@emmacurran7717]

I’m kind of surprised you turn the washer on the side. I have read it is not a good thing and mine came with shipping bolts so I am too scared to do that. It’s a pain to take off the front but probably the safest bet.

[@moneyfornothing3264]

What happened?

[@melindaoyos8018]

I know that voice!! My son relies on you for his car!!

[@KeyStar71]

and where do you get the best price for the shocks? better at amazon?

[@Easydread]

EBAY !!!!

[@donelldavis4035]

The auto repair guys!!!

[@thejbltester]

That’s vrt kicking in

[@hoptag]

My Samsung front load VRT spins out great on "spin only" mode but on a regular cycle it leaves clothes dripping wet

[@lafinest47]

how did you fix it? i have the same problem.

[@dariocampuzano9489]

Yes how did you fix it.. mine just keeps spinning

[@oliver-Barron]

I think my washer broke, it wont spin at all it used to make that loud noise and i think getting one snapped?

[@tonyconrad9135]

Are you the same guy from the BMW repair page?? Lol

[@jmp101694]

And a Mazda repair video I watched. Guy does it all 🤣

[@ybsunbreakable]

What about if it takes much cloths and could not roll,what could be d fault ????

[@user-xz1pw2ol7w]

I have Samsung wach machine same but repeat spin same solution??

[@firewall8047]

What does 3E2 mean as an error code i cant find it anywhere i have the same washer

[@bartek9907]

Te wibracje są normalne bo w tej pralce jest system VRT plus czyli ma zastosowane kule w bębnie które podczas rozpoczęcia wirowania rozkładają się po bębnie więc jak możesz zauważyć na początku się trzęsie a później już nie SORRY BUT I DIDN'T WANT TO TRANSLATE THIS😂

[@KeyStar71]

It did the same for me for a long time but now on top of that when the spining is slowing down it makes a huge noise and the machine stops because it vibrates too muich but now errors on the panel . So that means a shock or 2 are completly destroyed ? I will open it and see.. But it was for a long time doing exacly has yours before you change the shocks

[@nesco713]

My washer is spinning unbalanced and stays stuck on the spin cycle with 5 minutes and stays on 5 minutes. I think shocks need to be replaced.

[@25atiq]

Did your issue got resolved by replacing the absorbers?

[@nesco713]

@25atiq bought a new washer. Got rid of side loader and top loader...

[@nodrizzle3903]

Showed how to change the 2 easy ones. Didn’t show how to get at the front 2. Sorry. Need complete instructions.

[@arisdhaftvani7210]

My washer has the same look and it is keeps doing spinning section. Once it tries to accelerate for fast speed it goes for 3 seconds then it stops then the timer jumps up again, so always in the loop. Is this what you were experiencing?

[@joelamoureux]

JUst helped my neighbor fix this problem. Broken plastic bracket that was affecting the imbalance sensor, Drilled 6 1/4” holes and secured bracket to backing plate with 3 ty wraps. howtofixit.net/samsung-washer-not-spinning/

[@arisdhaftvani7210]

@@joelamoureux Thank you

[@Vol2169]

@arisdhaftvani7210 you said thank you to someone but I don't see a post. Did someone reply to your question about spinning?

[@arisdhaftvani7210]

@@Vol2169 I am sure he did. Forgot what he said, he should have deleted it. I ended up replacing my washer with LG.

[@Vol2169]

@@arisdhaftvani7210 thanks. Having same issue with my Samsung now. Was just trying to find a solution.

[@moneyfornothing3264]

What if it is only stuck in spin cycle?

[@blancavo3808]

Mine is doing the same. It freezes when it's supposed to to do the fast spin cycle to get the water out of the clothes. The drum starts out tossing the cloths around when washing but it won't the the spin cycle. The time stays the same.

[@alecjeremy82]

According to diagnostics mode instructions you do not run spin with the clothes inside you have to empty the drum because it does not readjust or tumble your clothes during the test mode that's why it's going off balance during your diagnostics