Scooter CDI Test

Glixal GY6 AC CDI amzn.to/3R4VtKj
HIAORS 6 Pin AC CDI amzn.to/3Upez0F
GOOFIT BLUE AC CDI amzn.to/3qVggVV
DC CDI BOX For For KYMCO amzn.to/3RWMtbj
Chinese Scooter Service Manual amzn.to/2LBfWb8
Donate to Virberello for Parts rb.gy/gzrtit
Subscribe to my youtube channel bit.ly/2Rcxr41
Visit My Tiktok / virberelloscooter
Hello, my friends. Today, I'll show you many way to test the cdi on your scooter in this Step By Step video . Plus, I will explain the advantages and differences in cdi with ac or dc voltage and how to check them with a multimeter . I invite you to stay tuned and don't miss any details. I hope this Scooter Fix Tutorial will help you!
Thanks for watching!

[@user-kg5kb7ob9b]

Your channel has saved me so much $ on my scooter ty so much

[@VirberelloScooterTips]

That was my goal when I started this channel to help people and save them lots of money . Thank you for watching my videos and happy holidays

[@jackplunderbones]

Omg, thank you so much for making this video! It was SO helpful in my learning about CDI's and testing mine to see if it was the cause of my scooter issues. Thank you!!! 😁🙏

[@VirberelloScooterTips]

Thank you for watching my video

[@MTBTexasBikeRider]

Wow 🤩 I really appreciate you explained the CDI so good in detail. It really helped me out to figure out what was going on with my motorcycle! New Subscriber! 👍😎🤘

[@VirberelloScooterTips]

Thank you for watching my video

[@clifforddeschaine6346]

Thanks for the imfo my friend!

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@lancejonesmusic]

I had a rough idle but driving seemed fine and was wondering if maybe my CDI was bad. This continuity test proved that is was fine. Thanks for helping me rule out one possibility!

[@VirberelloScooterTips]

Sometimes cdi under stress do not work perfectly even if with the continuity test look fine also try to replace the spark plug that could be why you have a rough idle 👍

[@lancejonesmusic]

@VirberelloScooterTips I already replaced the spark plug and also tested the ohms of the spark plug wire and it was above 7.500 ohm reading or so, replaced it with a new one, will see how it runs today.

[@lancejonesmusic]

Ok so after 30-45 minutes of driving around, the idle gets rough. It seems like the idle is "okay" until after a while, but I had to turn up the idle pretty high so it will not stall and the back wheel is spinning because the idle is too high. I tried spraying carb cleaner to find a vacuum leak, could not find one. Changed spark plug and the wire. cleaned out the air filter. My next guess was CDI but it was fine on the volt meter. I am going to order a new fuel filter, drain the gas and make sure the tank is clear of debris and replace the filter next. It has almost 32,000 miles. Maybe the engine is just getting old? It is a 2016 SYM HD200 EVO. (fuel injection, not carburetor)

[@VirberelloScooterTips]

wow 32k is a great mileage that can also be a valve clearance or worn out piston rings check the motor pressure to make sure but if that happen after 30 to 45 minutes you could have the valve spring little tire / worn

[@lancejonesmusic]

@@VirberelloScooterTips Well I found the problem after changing my spark plug wire, furl filter, petcock, testing cdi, new spark plug, valve adjustment and the list goes on. The spring had ripped through one of the clutch shoes on my clutch! I replaced the clutch shoe assembly and the bike runs great again! haha! No random rough idling and the back tire does not spin when ont he center stand anymore lol.

[@tainomario]

You locking great man i placed the blue cdi on my icebear vision 50cc 2022 with the orange spark plug cable because it didn't start with the black cable so my scooter just got more power in accelerating. I like it more with the blue cdi works great

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@Whatsgaming]

best scooter youtuber! Like if you agree!

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@mariobarata2382]

Thank you!!

[@VirberelloScooterTips]

You are very welcome 👍

[@johntrauger68]

Thank you for thr valuable information. I think my CDI might be bad and wasn't sure how to check. I'll try agin tomorrow and see how it goes.....

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@midnightwolf5660]

Please help I put in the blue CDI but it still limits my revs it refuses to redline it did increase my speed by 6-7mph but I'm still stuck at it never reaching the red line at all would it be better if I use the original and remove the rev limiter?

[@Floridawaves703]

thanks

[@VirberelloScooterTips]

You're welcome!

[@SC8terRiderMotoVlogger]

KYMCO No. 1☝️😎

[@noekimes1887]

I got a kymco downtown 300

[@SC8terRiderMotoVlogger]

@@noekimes1887 Congrats2x 🎊

[@matthewhoffmeister2557]

Question ? I am working on my son's 2007 Ricardo znen. What kind of cdi box ? Has the longer one in it but he had a neighbor work with it so not sure if this neighbor changed anything up ?

[@VirberelloScooterTips]

It can be difficult to determine the exact type of CDI box required for a specific scooter model without additional information. However, as the 2007 Ricardo Znen likely has a GY6 engine, a common CDI box used for this engine is the DC-CDI box.

[@ipkdipkd5165]

Hello. I got a guestion. I have a dc cdi (kymco) and when i use the black probe on the ground in the left corner in the bottom and the red probe on the top right, should it have continouity? It does with mine but shouldn't that be normal because they are both ground. Thank you for your reply in advance. Greetings from Holland.

[@VirberelloScooterTips]

Hello yes that is normal 👍

[@ipkdipkd5165]

@@VirberelloScooterTips Ah ok. Thank you.

[@The1NightBaker]

I've purchased one of the blue aluminum cdi. But didn't install noticed it only had 5 pins. Can you explain the difference it 5 and 6 pins.

[@VirberelloScooterTips]

The difference between CDIs (Capacitor Discharge Ignition) with 5 pins and those with 6 pins lies in their functionality and compatibility with different ignition systems. Here's a breakdown of the key distinctions: 5-Pin CDI: This type of CDI is commonly found in older motorcycles or vehicles with simpler ignition systems. It typically includes the following pins: a. Power Input: Connects to the ignition switch or the battery's positive terminal to provide power to the CDI. b. Ground: Connects to the vehicle's ground or negative terminal. c. Trigger/Pulse: Receives a signal from the engine's ignition coil or pickup coil to trigger the CDI's firing sequence. d. Ignition Coil Output: Connects to the ignition coil, which generates the high voltage required for spark plug ignition. e. Kill Switch/Engine Stop: Connects to the kill switch or engine stop button, allowing you to cut off the engine's ignition. 6-Pin CDI: This type of CDI is commonly found in newer motorcycles or vehicles with more advanced ignition systems. It includes the pins mentioned for the 5-pin CDI, plus an additional pin for enhanced functionality. The pins on a 6-pin CDI are typically configured as follows: a. Power Input: Connects to the ignition switch or the battery's positive terminal. b. Ground: Connects to the vehicle's ground or negative terminal. c. Trigger/Pulse: Receives a signal from the engine's ignition coil or pickup coil. d. Ignition Coil Output: Connects to the ignition coil for spark plug ignition. e. Kill Switch/Engine Stop: Connects to the kill switch or engine stop button. f. Rev Limiter/Speed Limiter: This additional pin allows the CDI to control the engine's maximum RPM or speed, limiting it within a specific range for safety or performance purposes. The presence of the sixth pin in a 6-pin CDI enables additional features such as a rev limiter or speed limiter, which are not typically found in 5-pin CDIs. If your vehicle originally had a 6-pin CDI and you have purchased a 5-pin CDI, it may not be fully compatible with your ignition system, potentially limiting certain functionalities or causing compatibility issues. It is crucial to ensure that the CDI you purchase matches the specifications and pin configuration required for your specific vehicle or engine model to ensure proper functioning and compatibility.

[@ranesryan9941]

Hi I'm new to the utube channel I hope this will get to you. I have a 2021 amigo ss 150cc. It's so hard to start cold that it kills battery trying when I'm jumping it from a car it takes me holding the start button for long periods and it eventually starts it's hard to keep going but once warmed up it runs great. What are some trouble shooting tips. I would really like to talk on phone if possible. I'm desperate I've missed a week of work already. Please help.

[@VirberelloScooterTips]

Hello my friend There could be several reasons why your gas scooter is not starting. Here are some common reasons: Faulty spark plug: A faulty spark plug can prevent the engine from starting. Check the spark plug to see if it is dirty, corroded or worn out. If so, replace it with a new one. Clogged air filter: A clogged air filter can restrict air flow to the engine, causing it to not start. Check the air filter and clean or replace it if necessary. Dirty carburetor: A dirty carburetor can also prevent the engine from starting. Try cleaning the carburetor or taking it to a professional mechanic to get it cleaned. or you need to check motor compression and do a valves clearance service Thank you for watching my video

[@ranesryan9941]

Thank you I I got it going. It was multiple things. Basically I changed all ignition parts. And bought a new duralast battery. My scooter had 12 miles when I bought it. It now has close to 8,000. And I out run the expensive scooters. Chinese scooters are Ok in my book. Thx again for all your videos. And watch for me because I definitely gonna support your channel.

[@chrisstokley7687]

OMG: $199 for oem ci dc... can u tell me if 1 these dc cdi replace mine ? its a 2000 savage ls650p

[@VirberelloScooterTips]

Wow $199 is lots of money I'm not sure if you can place a scooter cdi on a savage 650 but I can tell you that this cdi are not to reliable

[@keymanpacker9721]

How do you test the kill switch?

[@VirberelloScooterTips]

Hello Key man to test the kill switch wires on a gas scooter, you will need a multimeter, which is a tool that measures electrical current. Here are the steps to test the kill switch wires: Disconnect the kill switch wires from the rest of the scooter's wiring harness. Set your multimeter to measure resistance (ohms). Touch the probes of the multimeter to the two wires that were connected to the kill switch. The multimeter should read a very low resistance (close to zero ohms) when the switch is in the "on" position, and a very high resistance (infinite ohms) when the switch is in the "off" position. Activate the kill switch by pushing it to the "off" position and test the resistance again. The multimeter should now read a very high resistance (infinite ohms). Release the kill switch and test the resistance again. The multimeter should return to a very low resistance (close to zero ohms). If the multimeter readings do not match these specifications, there may be a problem with the kill switch wires or the switch itself, and further testing or repairs may be necessary.

[@kristianbrandstrom]

What if there is a spark, but it still has problems starting

[@VirberelloScooterTips]

Hi if you have spark but you have problems I will check the valve clearance and the compression 👍

[@Tomijus]

i have an adjustable cdi and the screw adjusts idling rpm

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@kristersgulbis2187]

Hello My blinkers dont work,is it possible the cause is cdi box change? Already changed regulator. And blinkers indicators doesnt work.🤯😇

[@VirberelloScooterTips]

Did you change the blinker relay ?

[@VirberelloScooterTips]

kzbin.info/www/bejne/mXvSgJmJfbqHn6c

[@kristersgulbis2187]

I dont have flasher relay🤯 I looked everywhere. Someone said maybe it is integrated un cdi or regulator?🤷‍♂️ Moded is peageot vivacity 4t Thanks a ļoti❤️🙏 IM going insane🤣🤣🤣

[@kristersgulbis2187]

@@VirberelloScooterTips i was riding one day and suddently my - wire from my battery came off,it was losening. And then my blinkers whent completely off.

[@kristersgulbis2187]

@@VirberelloScooterTips when i tried to start my bike,the indicators on dashboard show there are blinkers,but in real life when i press turn signals button there isnt anything alive.🤯

[@eddietrujillo172]

Yoooo.. can u sell me that DC CDI pls😂 I really needed one asap

[@eddietrujillo172]

Yoo honestly u need to talking about the 2 stroke dc or ac cdi they are ni ot the same and no one have a video on how to pin out a 2 stroke dc cdi

[@nickvlast3111]

My scooter uses an AC CDI, so I bought the blue one and it doesn't start, but when I plug in the old one it starts perfectly. Why you think this happens?

[@Pinhead_larry265]

The blue one uses DC current. You would need one that supports AC voltage

[@VirberelloScooterTips]

I have the blue AC cdi on my scooter for the last 5 years and is running great but sometimes few cdi are shipped already defective from the factory

[@VirberelloScooterTips]

I have the blue AC cdi on my scooter for the last 5 years and is running great but sometimes few cdi are shipped already defective from the factory Thank you for watching my video

[@Revelation1177]

@@VirberelloScooterTips what would happen if I plug in an ac cdi if my scooter uses dc I have the gator 50-s3 um not sure if its ac or dc

[@johnnyclaimerhaddadin195]

@@Revelation1177you would at the least blow a fuse if you’re lucky. Don’t even risk it!

[@Postalguy1]

Can this cause your bike to have 50% power ?

[@VirberelloScooterTips]

No I don’t believe so I think you need to replace the roller weight inside the variator but is not easy to pin point the problem if I don’t see the scooter

[@samhalderman3352]

My GY6 150cc has a small DC CDI.

[@VirberelloScooterTips]

Hello my friend thank you for watching my video

[@rkstew]

Do you have a mailing address, I would like to send you something