2010 Lexus RX350 Oil Change

Рет қаралды 37,412

Suburban Ranch

Күн бұрын

Пікірлер: 46

@As-le6rl 2 жыл бұрын

Most informative video I have seen for this model Lexus

@RS-lq6zm 2 жыл бұрын

Torque values. I suggest investing in/using a torque wrench. - Oil filter cap (canister) assembly is 25 N-m or 18 ft-lb. - Oil filter cap (canister) drain plug is 12.5 N-m or 9 ft-lb, - Engine oil pan drain plug is 40 N-m or 30 ft-lb.

@maurice2014 Жыл бұрын

I respect torque values but in this case it's unnecessary. The filter drain cap has a gasket and is metal, the filter cap itself it metal- threaded meaning you manually can't over-tighten it in the same way you can with metal on plastic (albeit sometimes, as I'm this video, you can make it more "snug"). The torque specs for RX oil components are basically the same as you hand tightening it. I torque everything else to spec.

@TheEmmauswalk 4 ай бұрын

Thank you. Finally, I got the torque specs.

@mjk9674 2 жыл бұрын

Don't forget always change the drain bolt washer also

@TheEmmauswalk 4 ай бұрын

Thanks!

@rdspam 11 ай бұрын

3:32 yikes. Torque on the filter housing is only 18 ft-lbs. It’s sealed by the O-ring, not the threads. Cranking it tight is a good way to break it - happens quite often. Loosing the oil cap before/while draining to better get everything out. Replace the crush washer on the drain plug. 2010 likely has substantial miles (235k on mine). High mileage 5w-30, as specified in non-CAFE countries, can slow/stop/prevent leaks.

@SuburbanRanch 11 ай бұрын

I’d say it was pretty close to 18 ft-lbs, just snugged it up. No need for a torque wrench for an oil filter! I don’t buy into the hype of “high mileage” oil. The engine has zero leaks after 175k miles, I’ll stick with synthetic oil at the weight the factory recommends.

@njsongwriter 3 жыл бұрын

Can't tell by watching but the oil filter cap torque spec is 25 N•m and the drainbolt on the oil filter cap is half that at 12.5 N•m If that's not followed sometimes the entire assembly wants to come off when you go to remove the drainbolt.

@SuburbanRanch 3 жыл бұрын

@JackTannehillPromotor Good info!

@hrandmahmoudi147 Жыл бұрын

Hi sir,it would have been better if you filled the oil filter with a little oil.🙏👏

@mjk9674 2 жыл бұрын

Also, First take off the filler cap and pull the dipstick out slightly and then remove the oil drain bolt

@backlineguy Жыл бұрын

When you reset the Maintenance warning, does it reset to 5000 miles? Thanks, great video!

@SuburbanRanch Жыл бұрын

@Backlineguy The oil service light will come back on in 5000 miles

@_valles3438 5 ай бұрын

Thank you so much!! First time doing a Lexus and I was wondering where the filter could be since in Honda’s one can see the little filter hanging out underneath

@DougHuffActorOfficial 2 жыл бұрын

Excellent info.

@davminks Жыл бұрын

Make sure to get the filter on tight, there's a reason you break it loose with a half inch cap, hand tight won't seal completely (turn until you hear the metal contact on the last half turn or so). Otherwise it WILL seep

@SuburbanRanch Жыл бұрын

@David Moore Just don’t go too crazy, it will be hard to get off!

@buckdashe2571 Жыл бұрын

@@SuburbanRanchactually….if you notice, it is an O’ring that seals the filter housing, NOT the torque. There is no reason whatsoever you would need to honk down on that that much.

@snapdiscgolf 2 жыл бұрын

Don't forget a crush washer on the oil pan plug. They don't come with the filters. ...his was stuck to the side of the oil pan and luckily didn't fall off.

@SuburbanRanch 2 жыл бұрын

@Dan Turner Been 22 oil changes and it’s still going strong ha. It is a good idea to change it though.

@TheEmmauswalk 4 ай бұрын

Awesome. Very detailed video. Thanks 😊

@criskatan Жыл бұрын

The 2010 on through to about 2014, or so, are the best iterations of the RX350. Some 2009's might be okay but you definitely want to stay away from the 2007 and 2008 RX 350's. Way too many problems/complaints.

@timandsuzidickey9358 Жыл бұрын

Thanks... very concise & informative

@frankyousif8451 Жыл бұрын

Best video thank you so much!!!

@alfredoangeles1008 2 жыл бұрын

Thanks!! For your video 👍🏽

@kevinnguyen4568 6 ай бұрын

Thank you so much! It is clear my questions. 👍👍👍

@HoomanM 2 жыл бұрын

Perfect ! thank u

@gmw1964z 2 жыл бұрын

Did you measure the extra 1.4 quarts? Mine always reaches the top dimple.

@SuburbanRanch 2 жыл бұрын

@g w Just eyeballed it on the side of the jug

@RS-lq6zm 2 жыл бұрын

From the owner's manual: "About 1.6 qt. (1.5 L, 1.3 Imp. qt.) is required to raise the oil level from low to full on the dipstick." You should also start the car, let it warm to operating temperature, shut it off, wait five minutes, then check. Simply checking after adding cold oil will not be accurate - cold oil flows slowly to the pan and there is no oil in the filter you just installed. It could read .4qt higher than it will after running, which will fill the filter and housing. Again, from the owner's manual: - With the engine at operating temperature and turned off, check the oil level on the dipstick. - Park the vehicle on level ground. After turning off the engine, wait more than 5 minutes for the oil to drain back into the bottom of the engine.