How to diagnose a faulty ebike

[@dudarino666]

One of the best tips from this video. Confirm diagnosis with known good parts if you can. As a car/bicycle mechanic, sometimes quickly swapping out a suspicious sensor, head unit, easily accessible part and retesting can save you time and headaches. Example, misfires on cars, swap the coil packs/ignition coils from the misfiring cylinder to the neighboring cylinder. Clear codes. drive until the car misfires. If the code changes cylinders its the coil pack, if it doesnt, its a spark plug. RARELY is it something mechanical with a single cylinder.

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@mikerbwind]

always useful videos mate. A good tip with the Purion is first to fit a cover since water ingress is most likely to happen by operating the buttons when the unit is wet due to rain etc...............and second to fit it on the bars very nearly vertical rather than horizontal. button presses become far more positive and the unit is better protected from both crashes and the elements.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments

[@bownsaway]

My bike has died too I am hoping it’s the head unit. Thanks for your advice and time and patience.

[@TheYorkshireBikeMechanic]

Hi, thanks for your comment, sorry for the late reply.

[@virkelie2]

Very interesting video! Wondering whether dead batteries in the Purion display could have explained why the ebike wasn't working?

[@TheYorkshireBikeMechanic]

Hi, thank you for watching and your comments, in answer to your question, no it wouldn't, the display was faulty, a new battery was tried earlier.

[@Admin-Ed]

Thanks for the video. Can you tell us more about the wheel size configuration through the head unit controller or the Bosch program?

[@TheYorkshireBikeMechanic]

Hi thanks for watching, wheel size configurations are changeable only by 5% this is simply to correct minor fluctuations, only manufacturer’s and Bosch can change these settings

[@moldavitetrips6753]

powacycle salisbury looks like it charges as al lights come on but when it starts it goes then dies ?

[@TheYorkshireBikeMechanic]

Unfortunately you will need to try a new one or take it to your dealer

[@dennisocampo4760]

I have a Bulls ebike am3 head unit is working fine but, when trying to engage the pedal assist nothing happens. Instead, it give me a wining noise coming from the motor. Van tell what’s wrong wit it. I’ve also tried to engage the walk mode and wouldn’t work S well. Thank you!

[@TheYorkshireBikeMechanic]

Hi, sorry but I would need to see the bike

[@declanclegg12]

I've got a ktm ebike and I purchased new lights and found the same thing with mine as it already had the loom ready must be a thing with certain bike manufacturers... Great video as always 👍 dave.

[@TheYorkshireBikeMechanic]

You are welcome

[@caramba10]

You didn't check the battery in the original Purion display? that would have been my first thing to check.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments, yes I did, but I wanted to make sure that we had a good video to make. A simple battery change if they were depleted in the display would have saved all the checking of the other components which made for a better video, lucky enough for me they were fine.

[@Stevo_YouTube]

Mine keeps turning off. Main battery is fine but keeps turning off. The Purion display is not giving a low bat warning. Should I try that anyway. Just tried cleaning main battery contacts but hasn't fixed the fault. If it's not the display I'm not sure where to go next. Called a local repair shop and they suggested a new motor straight away but I feel like I should try everything else first.

[@timothybuchli133]

I bought a new Trek Rail 9.8 Gen 4. When I start up and ride the power is good for about 15 seconds and then I get an orange flashing light on the display. It will then not let me move to a different power and the power will shut off at around 10 miles an hour. Have you had this happen to you before? Any ideas of what could be going wrong? Thank you in advance! Tim

[@TheYorkshireBikeMechanic]

Hi, it's difficult to diagnose an issue like this without plugging it in especially when you are getting the orange led before it starts to mis-behave. it could be a number of things but It really needs to be booked in with your bosch dealer

[@helenhamer9700]

Great video, very informative. I recently bought a 2nd hand xiaomi himo z20 however the display unit won't stay turned on (I have to hold the power button down) when it is on it displays an empty battery however the indicator light on the battery displays full. Any ideas on what could be wrong? Many thanks.

[@TheYorkshireBikeMechanic]

Hi Helen, sorry I don't have the diagnostics for it to help you.

[@otilbarcu478]

Hi man with bosch diagnostic tool can i find witch it°s the problem with error 500?the motor it°s refuse to start,i change all bearing end the same problem with this error 500.thank you

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comment, you will find that if the 500 error does not resolve after re-writing the firmware in the motor by the diagnostic tool then replacing the bearings will make no difference either

[@Fluiding]

where can you download the diagnostic software for purion from?

[@sharnikajones4636]

Hi I'm wondering what need to do with my vitilan u7 it's been give me an issue on the meter giving me a empty read battery symbol and my battery itself read full

[@TheYorkshireBikeMechanic]

thanks for watching and your comments, sorry I have no experience of that system

[@Stevo_YouTube]

Hi mate. Love this video. I've got a Cube with Bosch Performance CX 4, Purion display and it turns on but won't stay on. Just checked the battery and is charged, cleaned the contacts and put it back on but still doing the same - display and motor turn off after a few seconds whether it's stationary or in motion. The motor works for as long as it stays on for. Any idea what to look at next as local repair guy suggested new motor and that seemed extreme as a first option. It's out of warranty so I may as well have a little go myself first.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comment. This could be a purion display fault. it needs to be plugged in to diagnostics to trace the fault, if you dont have anyone to do that then the only way to find out is to change the display for a new one to see if that solves the problem. It could also be a simple firmare update.

[@Stevo_YouTube]

@@TheYorkshireBikeMechanic Thanks I will try those before new motor. Cheers!

[@scootjockey]

Thank you for the video my battery in my raymon with the px2 yamaha motor went error 74 after 10 months took it in battery fault on computor was diagnosed have to get a new battery did everything by the book.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,

[@dianecocoros8738]

What do you know about ebikes accelerating on their ow, to a point where I had to turn it off and turn off the road. Is it a 'safety' issue?

[@TheYorkshireBikeMechanic]

Hi thanks for watching, I would say that this is a massive safety issue. Please take it to your local ebike dealer that can work on your bike

[@cadena.aceitosa]

do you know what error 550 means with bosch CX units? my symptoms: PURION Display sometimes on and sometimes not, when may turn ONE i can ride but after some footrounds the ebike turn off i can turn on again some pedal work but turn of again.... some guy from TREK help me and he said bosh diagnostic said error 550... according hum i need to replace with a new motor

[@TheYorkshireBikeMechanic]

Hi, has the bike been diagnosed by your dealer

[@cadena.aceitosa]

they said error 550 according bosh system diagnosys @@TheYorkshireBikeMechanic

[@michelstoel2921]

Just got a new screen for my ebike and its giving e10 faultcode. Could the last screen that got waterdamage have messed up the electronics? Or do i need to reset someting?

[@TheYorkshireBikeMechanic]

Hi, thanks for watching, I assume that the previous display showed nor errors, check to purion connection at the motor, make sure no bent pins, if they are ok, sorry but I will need plugging in at your dealer.

[@michelstoel2921]

Alrighty thx, i will try messimg around with the cables to the controller. If nothing works, problem is my bike is an esmaster, and esmaster just went bankrupt lol. Can any dealer fix it?.

[@ElectrifiedExcellence]

Does anyone know any 3D printers who make wind deflecting fairings for ebikes? I'd love to add some to mine.

[@keyboardpatriot]

I went up a hill on my ebike and it would give me burst of power on and off till I got home. I used it again for weeks after with no issues, I went up the same hill the other day and this time it stopped working when I got to the top and I nearly broke my legs trying to cycle the tank home. I've been up steeper hills with no issues, the battery works, walking assist works, but when I use peddle assist it will give me one small amount of thrust then nothing after that, if I turn it off and on again it will just do the same thing. Do you have any idea what could be wrong please?

[@JaydaGoat580]

Did u ever figure out the issue

[@1jwh1]

Great video,👍 would have liked to have seen the removal and fitting of the new unit in real terms is it a 2 minute job? How much would this service cost in labour? 👍

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,, the new display was £94, the labour including fault finding and testing, 1.5 hours £47 inc vat

[@tangomike01]

Thats one of the bf est vids i have watched, thank you,

[@TheYorkshireBikeMechanic]

You are welcome.

[@J0nny61]

Great logical step by step diagnosis Dave. So just for my benefit, can you confirm that the firmware is packaged in the Purion display? On another subject, my Purion steams up in the display window every winter. I don't pressure wash, but even though it seams to be absorbing moisture, it works perfectly. Should I be concerned and if so what remedial action would you advise?

[@soundwave6769]

you can fit a kiox retro fit kit so you can also use the app on the phone as use it on my gen 2 cx motor but you might need a firmware update from the dealer software

[@BH-cy9tb]

I have a 2021 trek rail this is my second winter with the bike and just noticed the same thing. I also keep water away from display when washing. I did not have the problem last winter. 🤔

[@micktheshaggy3977]

As for the steamed Purion: there are clear silicone covers available for Purion display, these can decrease the possibility for the unit to absorb the moisture. But before you would put it on, at first you should get rid of the moisture that is already there. You can leave the unit somewhere close to the radiator, where the air is very dry. Or, if this not helps, put the unit into the plastic zip bag together with couple of silica gel bags (you can find them in your new shoes when you by them). In both scenarios, the effect will be better if you could remove the backplate to let the air to circulate (but most probably it will void your warranty).

[@islandaerial3414]

Mine fogged up last winter but, hasn't done so this winter. Weird Have you tried putting your display in a bag of rice?

[@BH-cy9tb]

@@micktheshaggy3977 I had a screen saver from a phone I cut to size to fit the purion from day one when I got it. And I just checked my ebike and the fogginess is gone. I wonder if it was from the screen saver.

[@JPBrewer1]

Your shop looks really nice , well equipped and tidy. I'd love to have a shop just like yours.

[@TheYorkshireBikeMechanic]

Thanks 👍

[@bobnboo]

My purion initially went pixelated due to water ingress but I could still ride the bike which I have been doing but now for over a year. But now the head unit only stays on for a few seconds and goes off . It's not the batteries in the unit either. I would love to come to you but I'm in Portsmouth but Do you have any recommendations for a good repair shop down in Portsmouth please . Great video by the way

[@TheYorkshireBikeMechanic]

Hi, thank you for watching and your comments, sorry but I don't know anyone that far down

[@craigjohnson6004]

Hey Mate, I've got a Trek Rail 9.9 2022 model with 2400 plus miles on it. I'm having Intermittent power shut offs when riding in the slow/moderate speed chatter (rocks). Usually the power drops off for a second or two and then comes back on. Occasionally it shuts all the way off and I have to push the power back on at the kiox. When I loose power it shows up on the kiox and then comes back on. I've taken it to the dealer and they've contacted Bosch, but no answers so far. Do you have any suggestions? I had a Rail 9.7 and it did the same thing, it was never fixed and they gave me this bike as an upgrade.

[@TheYorkshireBikeMechanic]

Hi, thanks for your comments. This is so difficult to diagnose. We need to bike in the workshop. It does sound like it’s a power issue, faulty connections need checking, any faults logged? It’s a case of swapping stuff out. Is it under warranty?

[@craigjohnson6004]

@The Yorkshire Bike Mechanic no I think the warranty has expired, no codes show for the issue either, that's why they are contacting Bosch. Thanks for getting back to me, I was hoping you'd have seen this before. I'll let you know if they figure it out so you'll have the info for the next guy.

[@IamCutePanda]

Could you please make a video on how to retrofit additional battery, when it is possible, I am going to do it with my RaM Nevo ..

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comment, next time I do one I will

[@IamCutePanda]

@@TheYorkshireBikeMechanic please do not forget to say some words about the firmware, it looks like a big issue...I mean just plug-in additional battery and installation on the frame is not a problem, but.. firmware to force it works as dual battery..if it is possible very very interesting

[@IamCutePanda]

@@TheYorkshireBikeMechanic thank for your videos and efforts!) Amazing content! It is a pity, that l live in another country, I would visit your workshop;) but I know one guy who is a Cornish man, he is 😎 , maybe you too Cornish)

[@LorettaBright-q8e]

My bike has power but after I lent it to my mate a I got it back a the power to back tyre is in reverse why is it not going forward

[@TheYorkshireBikeMechanic]

Really?

[@luigiprovencher]

What about an unresponsive PAS and throttle? Motor isn't engaging when the PAS is in 1 or 2 and neither is the throttle. This is when first trying to use the bike. It's intermittent problem and unpredictable. Once it starts working it doesn't happen in a middle of a ride or anything like. The only other clue is that I just got a brake error on the LCD.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching, that could be a number of things, the brake error could cause all of your symptoms, that needs fixing first.

[@Forward__Unto_Dawn]

Great videos! Can a common bloke like myself get that software and use it at home? And what is it?

[@TheYorkshireBikeMechanic]

Hi, no sorry, its dealer only stuff

[@a11eex]

I believe all Scott e-bikes come pre-wired for lights. I’m using the front wire only which leaves the rear cable exposed - probably not the best idea!

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments, its a good idea if they are already in there as long as they are not enabled.

[@a11eex]

@@TheYorkshireBikeMechanic Yeah, they have to be enabled still. Until I get a rear light, I’ll see what I can do about capping off the end of the rear lead as it is exposed somewhat. I could take it out, but I prefer the plug in the socket keeping dirt/water at bay. Loving your YT Channel by the way 👍🏻

[@abdellatifkhyi1724]

Hi thank you for useful videos i want to khnow how match cost the logiciel thanyou

[@TheYorkshireBikeMechanic]

Hi, Glad to help, thanks for watching and your comments, the display was just under £100

[@abdellatifkhyi1724]

@@TheYorkshireBikeMechanic not the display but the diagnostic tool thanks a lot

[@mohamedbelghit9647]

Wo kann man sich die diagnosesoftware runterladen

[@reeseprince8]

My display doesn't work nor my electrics on my super73 so I'm hoping this can help

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@reeseprince8]

Still doesn't work it could be a dodgy controller

[@GoranAntunovic-nb9xz]

Does the mileage reset when a new display is installed ?

[@TheYorkshireBikeMechanic]

Hi, no, the milage in is stored inside the motor

[@GoranAntunovic-nb9xz]

@@TheYorkshireBikeMechanic thank you for your reply

[@RichardTShebora]

Great video. If you swap any part into a bike for diagnostics that part is now used. At least it's an open box part. You do discount those to clients that get a part that's previously used for diagnostics, right?

[@TheYorkshireBikeMechanic]

Hi thanks for watching. We don’t sell the parts used for testing purposes. Once we find the faulty part we saw it out for a new one

[@BH-cy9tb]

Yes if I ever need to replace my head unit does it need to be programmed at a shop or can I just install new unit. Thanks. Really good info 👍

[@1brokenspoke189]

I asked this question at my local bosch centre and was informed that you can just plug Purion in and it will work no update is needed

[@BH-cy9tb]

@@1brokenspoke189 wow that’s great news when and if I ever need a new one. Thanks 👍

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,, you can do it without the need for programming but there maybe updates.

[@susanparminter]

Can you help me find what error 7 is on my ezebike

[@TheYorkshireBikeMechanic]

Thanks for watching and your comments, sorry I cant work on them

[@shaunmarston7168]

Hy up Dave i Carnt find the link for eBay can you help cheers 👍

[@TheYorkshireBikeMechanic]

Hi, here ya go www.ebay.co.uk/sch/i.html?item=304776944345&rt=nc&_trksid=p2047675.m3561.l2562&_ssn=cycle-fast

[@jpcycleservices3810]

The minute I saw the head unit, I knew it would be that, as my wife had a brand new bike and it her head unit went within weeks. Good to watch though.

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@jonnypaget]

Can you get hold of bosh BMS Dave??

[@TheYorkshireBikeMechanic]

you mean the software

[@jonnypaget]

@@TheYorkshireBikeMechanic No the battery balance board in the battery pack

[@lisacuthbertson5744]

I have got error code E004 on my electric bike model v20 pro does anyone know how to fix it please

[@TheYorkshireBikeMechanic]

Hi, thanks for your message, sorry im not familiar with this bike.

[@RBARCLAY-m2d]

We need help from USA with ebike no work!!

[@GNX157]

So what was the general cost for this part or repair? Was it under warranty?

[@jpcycleservices3810]

My wife had the same issue on a brand new bike and Trek quoted £100. Obviously she refused to pay as the bike was weeks old.

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments. The bike was out of warranty, The total cost was £144.00

[@DaleStrickland]

This was fantastic thank you. Not sure if it'll solve my Voltbike Yukon 750 not turning on at all but at least I have some next steps!

[@TheYorkshireBikeMechanic]

Glad it helped, thanks for watching

[@1brokenspoke189]

Great in depth video with lots of useful information many thanks .

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,

[@mrnemo1480]

Did you update the system after the repair...

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments, Yes I did

[@benvandoeland9123]

Thanks for all the info...well explained...

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@royayersrules]

I imagine you lose your data when a new head unit is fitted? i.e total mileage etc.

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching, no, the data is stored in the motor

[@paro2210]

I would have put some electrical tape on the ends of those wires, just to be safe. Also I would never have the battery in while plugging stuff in and out, its against my technician instincts. The best practice is to always take out the battery before doing stuff like that. Other than that great video.

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@garybennett9868]

Brilliant Job Dave

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments, cheers

[@waynechurchill7212]

Wish you where close to my area

[@TheYorkshireBikeMechanic]

Hi Wayne, sorry.

[@islandaerial3414]

Those wire connections don't look to be in a very smart place whatsoever. What model is that for future reference? Thanks

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,

[@kevintraynor4508]

If it's the back end of Jan then feb is not going to be any warmer

[@TheYorkshireBikeMechanic]

Hi Thanks for watching and your comment, too true

[@SingletrackScene]

Informative as always! Thanks Dave!

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,

[@iTCXtreme]

As always, great video 🙂👍👍👍

[@TheYorkshireBikeMechanic]

Thank you

[@codefields]

Great video as usual, thanks for sharing the knowledge 😊

[@TheYorkshireBikeMechanic]

Hi, thanks for watching and your comments,

[@DavidLusted-s5j]

You could have saved yourself 20 mins of messing about by just plugging the new purion on and you didn't check the purion battery either even though I doubt if that was the issue.

[@micktheshaggy3977]

Top notch content, thanks!

[@TheYorkshireBikeMechanic]

Hi, Thanks for watching and your comments

[@RBARCLAY-m2d]

I NEED throttle and motor power to ride ebike display unresponsive!! Quickly!!

[@johnreese3762]

Great info, thanks!!

[@TheYorkshireBikeMechanic]

No problem!

[@VovanCBR]

why not to install Kiox instead of this outdated purion

[@TheYorkshireBikeMechanic]

Hi, Thank you for watching and your comments, customers choice

[@richardwalker5906]

Good watch 👍

[@TheYorkshireBikeMechanic]

Thanks 👍

[@productreviewspecialist]

You need to go back to electronics 101 bacics. You COMPLETLY did not mention parasitic drain causing premature battery discharge!!!!!!!!!!!!

[@trevorhague4451]

What parasitic drain do you mean are you talking milli amps or a fully charged battery discharging over night

[@RBARCLAY-m2d]

We NEED no guessing advised quickly 100% ALL wires ebike!

[@Extremegaz25]

Howdo dave

[@TheYorkshireBikeMechanic]

Hi, hope your good

[@ssse3123]

In summary - have another full motor set available to swap out bad parts 😄

[@TheYorkshireBikeMechanic]

yes, we need a new component for each possible faulty one

[@p4ult1]

Another Bosch motor with a missing logo disc. The factory must stick them on with pritstick 😂

[@TheYorkshireBikeMechanic]

Pretty much!

[@RBARCLAY-m2d]

Robert Bosch need no help they have already the data!!

[@chrismade123]

unbelievable busch hide the buttonder t cover

[@mikerbwind]

Bosch dont.......the bike brand has chosen to install the battery thay way with a cover on it.

[@wdhewson]

I've been finding that Bosch ebike units are unreliable and expensive.

[@john-wq8kf]

Well was that not the most logical thing to do

[@TheYorkshireBikeMechanic]

Yes it was, we need more people that think logically.

[@RBARCLAY-m2d]

You see!! Dead ebike!!

[@williamjeffersonjameslowma3970]

Can I receive my 300 dollars

[@TheYorkshireBikeMechanic]

hi, thanks for watching , why??

[@bobwilliamson5574]

As useless as a chocolate chastity belt 😂

[@islandaerial3414]

Thanks for that translation

[@TheYorkshireBikeMechanic]

lol

[@ColeBonney]

Hi Dave, Do you have a email or contact number?

[@TheYorkshireBikeMechanic]

Hi, yes we do, our shop number is 01422 766086

[@dennisocampo4760]

I have a Bulls ebike am3 head unit is working fine but, when trying to engage the pedal assist nothing happens. Instead, it give me a wining noise coming from the motor. Van tell what’s wrong wit it. I’ve also tried to engage the walk mode and wouldn’t work S well. Thank you!

[@TheYorkshireBikeMechanic]

Hi, sorry I really need to see the bike to find out what’s wrong.