Toyota 22R 22RE Timing Cover, Water Pump, Oil Pump: Bolt Specs, Location & Install

  Рет қаралды 27,199

6th Gear Garage

6th Gear Garage

2 жыл бұрын

If you mixed up the location of the timing cover/oil pump/water pump bolts on a 1985-1995 Toyota 22R or 22RE engine, then this video is for you!
Diagram: 6thgeargarage.com/toyota-22r-a...
Here's a steel ruler with inches and mm, similar to the one I was using: amzn.to/4eu7s0L
Here's a thread pitch measurement gauge: amzn.to/3KPXnh0
I don't have Patreon or ask for donations but you can support the channel with some rad Yota gear from my store: 6thgeargarage.com/merchandise/
Here's the link for used OEM Toyota parts: 6thgeargarage.com/yota/
Follow Us:
Instagram: 6th_gear
/ 6thgeargarage
/ 6thgeargarage
Here are some other Toyota videos you may find helpful:
How to restore cracked dash (part 2): • Part 2: How to Restore...
How to Remove 1980's Toyota Pickup/4Runner Dash Pad Cover: • How to: Remove 1980's ...
Remove Toyota Truck Rear Glass Window: • How to Remove Toyota T...
How to clean/Restore Toyota Pickup/4Runner Door Panels: • How to: Clean/Restore ...
Toyota Door Disassemble: • How To: Disassemble a ...
Rebuild front knuckle & replace birfield joint: • Toyota Solid Front Axl...
Remove an Entire Toyota Rear Axle Assembly: • How to Remove an Entir...
Install/Upgrade to V6 1" Master Cylinder on 4 cyl Toyota: • How to Install/Upgrade...
Install Toyota Rear Axle Bearing, Oil Seal - WITHOUT a Press: • Install Toyota Pickup/...
Replace Toyota Drive Shaft Center Support Carrier Bearing: • DIY: Toyota 4x4 Drive ...
Trail Gear Hi-Steer install: • Trail Gear Hi-Steer in...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Fixing Floor and Rocker panel rust: • Fixing Floor and Rocke...
Remove Headliner in Toyota Pickup Truck: • How to: Remove Headlin...
Remove Toyota Pickup & 4Runner COMPLETE Dash: • How To Remove Toyota P...
Toyota 22RE Engine Teardown: • $100 Toyota 22RE Engin...
22r Compression Test: • How to: Compression Te...
Remove Toyota 22RE Engine & Transmission: • Remove Toyota Pickup T...
Toyota Pickup/4Runner Vent Window Conversion: • How to: Toyota Pickup/...
Toyota 4x4 Transfer Case Rear Flange Oil Seal Replacement: • DIY: Toyota 4x4 Transf...
Replace Pinion Oil Seal in Rear Diff: • How to Replace Toyota ...
Remove Door Panel: • How to: Remove Toyota ...
LED Headlight Conversion: • How to: Install Toyota...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Breaking a Rusty Toyota Frame in Half: • Breaking & Cutting Up ...
Toyota Pickup Fiberglass Bed Review: • Toyota Pickup Truck Fi...
B-Pillar Trim Removal & Install: • Toyota Pickup/4Runner ...
How to disassemble Vent Window: • How to: Disassemble Ve...

Пікірлер: 57
@blitzerman8
@blitzerman8 2 жыл бұрын
Glad to see the 22R/E getting some KZbin love. I've got an early RE in my '84 Celica and there is a serious lack of love on modern media compared to other engines.
@lydeange1
@lydeange1 Жыл бұрын
Great video! Would love to see more assembly videos this clear and concise
@83drummerboy
@83drummerboy 2 жыл бұрын
You’re a hero. Thanks for the video and keep them coming!
@boi5599
@boi5599 2 жыл бұрын
Thank you this info is gold to me! Just bought a celica and it was leaking bad, realized that it’s missing 3 of the big bolts that hold it the cover on! Hopefully this solves my leaking issue!
@carlosgutierrez3319
@carlosgutierrez3319 6 ай бұрын
Best video on the internet as I am rebuilding my first 22RE motor on my 1985 Celica GT
@patricksainz4484
@patricksainz4484 Жыл бұрын
Thank you for the bolt information, it helped greatly
@6thGearGarage
@6thGearGarage Жыл бұрын
Glad it helped
@sciflyer67
@sciflyer67 2 жыл бұрын
Thanks for a very timely video! No pun intended.
@sxstexan1956
@sxstexan1956 4 ай бұрын
Wow you really stepped your game up! Good work.
@6thGearGarage
@6thGearGarage 4 ай бұрын
Thanks!
@andrewarchibeque1262
@andrewarchibeque1262 5 ай бұрын
@6thgeargarage you are the man!
@chiko98
@chiko98 2 ай бұрын
You’re a life saver
@muchristian
@muchristian Жыл бұрын
Been going between a 79, 83 and 85 FSM as well as a Haynes and wasn't able to get all of this info. I have been measure holes before finding bolts as mine came pre disassembled. Thanks for making that chart.
@6thGearGarage
@6thGearGarage Жыл бұрын
Glad to help!
@yano4473
@yano4473 6 ай бұрын
I swear im inside a motor that's been taken apart before. I didnt think so initially, but my four large 14MM bolts are opposite of this. Two have two washers and two have just one. Three are the same length and one is SHORTER. Really troubled bc the guides are definitely original. 84 Celica.
@williamleffler4067
@williamleffler4067 22 күн бұрын
Same here! Did you figure it out?
@ToyotaSR51989
@ToyotaSR51989 8 ай бұрын
Toyota fans yes we are number one every time we drive or 4RUnner’s
@tythesnoman
@tythesnoman 5 ай бұрын
Dude thank you!!
@6thGearGarage
@6thGearGarage 5 ай бұрын
You bet!
@damonjensen833
@damonjensen833 Жыл бұрын
Awesome bought an engine and truck from someone who tore it apart and didn’t want to put back together and he just threw the bolts in a big bucket.
@josuejimenez7520
@josuejimenez7520 2 жыл бұрын
Extremely helpful! I went through your library and I see you have a breakdown of a 22r engine but not A full details rebuild. I want to do a rebuild but Most videos out ther skip a bunch of steps.
@6thGearGarage
@6thGearGarage 2 жыл бұрын
I plan on doing a full rebuild one of these days... I have too many projects!
@KartsAndCoffee
@KartsAndCoffee Жыл бұрын
Quick question! I’m doing a timing kit today and have most of the motor disassembled. I’m trying to get the crank bolt off using the bump start method. Do you know if I can bump it while the distributor shaft is removed? Thanks for your time and experience.
@6thGearGarage
@6thGearGarage Жыл бұрын
That should be fine, as there just will be no spark. I actually have a video of doing the bump start on a 22r pickup: kzbin.info/www/bejne/fXSoZINudqllqKs
@jonathanornelas9238
@jonathanornelas9238 Ай бұрын
Hey man thanks a lot for the video I'm about to put my cover back and definitely you are a life saver just one question bolt number 1 it was already missing when I started the job any idea were I can get one just got the new bolt kit from yotashop but it didn't come with it also that measure bot tool were I can get one just like that one thanks in advance
@6thGearGarage
@6thGearGarage Ай бұрын
Here's a steel ruler with inches and mm, similar to the one I was using: amzn.to/4eu7s0L and here's a thread pitch measurement gauge: amzn.to/3KPXnh0 (I have one of these mounted to the wall and use it all the time!)
@daylinpaxtor
@daylinpaxtor Жыл бұрын
Hello, can you help me with the diagram of the distribution cover, which is rebol, and the screws, I no longer remember where each one of them went?
@6thGearGarage
@6thGearGarage Жыл бұрын
What engine do you have?
@conormiller3662
@conormiller3662 Жыл бұрын
Awesome video! I do have one question tho, how are those two water pipes sealed, is there some sort of pre-made gasket? Or do you just use silicone?
@6thGearGarage
@6thGearGarage Жыл бұрын
Thanks! There is a small gasket that goes on the flange.
@jwtbird1570
@jwtbird1570 2 ай бұрын
What's the bolt length for the AC bracket bolts that go on the bottom right? do you know?
@6thGearGarage
@6thGearGarage 2 ай бұрын
Sorry, I do not know the length of those bolts.
@erasmoochoa8744
@erasmoochoa8744 7 ай бұрын
Is it possible to use the same cover for convert to dual timing Chaín, same oil and water pumps, with just replace the oil pump driver gear?
@6thGearGarage
@6thGearGarage 7 ай бұрын
I've never done the conversion, but it looks like there may need to be some custom work done to the cover, maybe clearance issues? www.lceperformance.com/22R-RE-RTE-LCE-Dual-Row-Timing-Chain-Conversion-Ki-p/1015012.htm
@erasmoochoa8744
@erasmoochoa8744 7 ай бұрын
@@6thGearGarage in some forums people say that is direct fit but I do not know, I have a friend whom has a toyotas yunkyard, I am going to compare timing covers (single and dual) and mount timing sets to see if any modification Is needed
@erasmoochoa8744
@erasmoochoa8744 7 ай бұрын
I have just received the LCE kit and the cover has some differences against the OEM
@damiandavies4632
@damiandavies4632 3 ай бұрын
Would you happen to know the 22RE torque specs for the chain guide and tensioner?
@6thGearGarage
@6thGearGarage 3 ай бұрын
I just looked through the factory repair manual for my 1985 and it's not listed. I would guess 16 or 20 lb ft
@damiandavies4632
@damiandavies4632 2 ай бұрын
@@6thGearGarage I found it. Chain Guides: 16 ft-lbs/22 N-m and Tensioner: 14 ft-lbs/19 N-m. This is only for the 22 R-E engine.
@damiandavies4632
@damiandavies4632 2 ай бұрын
Do the coolant pipes need a gasket or RTV?
@6thGearGarage
@6thGearGarage 2 ай бұрын
Yes, either one will work.
@hmuong
@hmuong Жыл бұрын
a lot of the toque value you provided here are incorrect!
@dwizdofoz.
@dwizdofoz. Жыл бұрын
PLEASE buy a metric ruler, this whole engine is metric and inch measurements are redundant ;) Great video mate.
@6thGearGarage
@6thGearGarage Жыл бұрын
I actually have one, but most of my viewers are here in the US and US doesn't like metric for some reason. Cheers!
@dwizdofoz.
@dwizdofoz. Жыл бұрын
@@6thGearGarage yeah I know, was just busting yourchops mate. They're sneaking it in over there though.
@KartsAndCoffee
@KartsAndCoffee Жыл бұрын
Do you have a link to download the diagram?
@6thGearGarage
@6thGearGarage Жыл бұрын
Oh I suck, forgot to put it in the description... It's there now!
@KartsAndCoffee
@KartsAndCoffee Жыл бұрын
@@6thGearGarage nah you’re good, thank you.
@retro_88yota
@retro_88yota 2 жыл бұрын
this is legit the worst part about rebuilding a 22re. what's even worse is a/c and non a/c trucks have different length timing cover bolts.
@6thGearGarage
@6thGearGarage 2 жыл бұрын
And I never even knew that... good info- thanks!
@retro_88yota
@retro_88yota 2 жыл бұрын
@@6thGearGarage yep. it kinda sucks. my 22rs never did me wrong but I am really happy I opted to engine swap my pickup. no more timing chain shenanigan's
@6thGearGarage
@6thGearGarage 2 жыл бұрын
Did you go 3.4?
@retro_88yota
@retro_88yota 2 жыл бұрын
@@6thGearGarage nope a 2.7L 2tr-fe from a 2015 Tacoma. I have a few (mediocre) videos covering the swap on my channel if you are curious.
@jerryrussell2600
@jerryrussell2600 9 ай бұрын
He goes way too fast at grabbing bolts out and talking.
@6thGearGarage
@6thGearGarage 9 ай бұрын
There's a chart you can download in the description... Or you can slow the playback speed on the YT player if you're watching while trying to reassemble your 22RE ;)
Red❤️+Green💚=
00:38
ISSEI / いっせい
Рет қаралды 84 МЛН
КАК ДУМАЕТЕ КТО ВЫЙГРАЕТ😂
00:29
МЯТНАЯ ФАНТА
Рет қаралды 10 МЛН
Каха заблудился в горах
00:57
К-Media
Рет қаралды 8 МЛН
22R Timing Chain Replacement // Water Pump // Oil Pump
15:49
Isaac Dozier
Рет қаралды 15 М.
Best Performance Mods for your Toyota 22R/E!
16:45
Sir Drifto
Рет қаралды 46 М.
OLDER TOYOTA 22R TIMING CHAIN OR TIMING COVER INSTALL
17:44
Ron Williams
Рет қаралды 230 М.
Celica 22RE Dual Row Timing Chain Upgrade
12:00
Slow Car Salon
Рет қаралды 18 М.
Rupert Roams - 22r Head Swap and NEW HEAD GASKET! Part 1
22:11
Northeast Adventure Company
Рет қаралды 24 М.
Toyota 22RE timing chain How To, Easy.
13:46
ChopIt'n'Roll Motorsports
Рет қаралды 41 М.
Why Do Toyota Water Pumps Leak? How to Prevent Them From Leaking?
27:50
The Car Care Nut
Рет қаралды 351 М.
Exhaust Tips GLE 63s
0:19
Straight Piped by: Gexhaust
Рет қаралды 1,4 МЛН
My New Model 3 Performance Almost Ran Out of Battery 😳😱
0:24
Tesla Flex
Рет қаралды 28 МЛН
Every car need this.#car #carhack #shortsyoutube
1:00
Chaudery Auto Traders
Рет қаралды 6 МЛН