Trick Chassis Ford 9" FINAL INSTALL - Axles - Disk Brakes - and Brake Lines

I am not a professional. This video is for entertainment purposes only. I am not sponsored by any company mentioned in this video. I did this install based on my own research and used my own money to purchase the products..
In this video, I finally get the Trick Chassis rear-end installed with the brake lines and disk brakes. I can roll it around again!! now we can move over to getting the engine and transmission installed. Which brake hose? The 9" or the 16"? As always links to the parts I used below. If you have questions please ask!! The torque specs that I called out are from Trick Chassis and Calvert. Always reference the manufacturers recommended torque specs when working on or modifying your vehicle.
Thanks for watching, don't forget to like, comment, and subscribe!!!
Rear End Install Links
Flare brake line to 3an fittings - 2 pack
www.amazon.com...
3" U Bolts
www.amazon.com...
MOOG Leaf Spring Bushing
www.amazon.com...
Russell 16" Brake Hose - 10mm to 3an
www.amazon.com...
Russell 9" Brake Hose - 10mm to 3an
www.summitraci...
3/16" Steel Brake Line from O Reilly - I used 2
Part Number PA-330
3/16" insulated clamps that I used on the rear-end to secure the brake line - You can buy these separately at Lowe's
www.amazon.com...
Russell Brake Line Mounting Brackets
www.summitraci...
Clips that hold brake fittings in the brackets - Pack of 4
www.summitraci...
FelPro 9" Center Section Gasket - Part Number 55074
Permatex Oil Resistant Silicone Sealant - Part Number 75190
Lucas 80W-90 Gear Oil - 1 Gallon
www.amazon.com...
CalTracs S10 NOT THE LOW PROFILE - Summit
www.summitraci...

[@Chrissutter35]

Mannn I was sitting here following your build trying to replicate in my driveway with a dam 350 and now you had to go and get all fancy on that dam rear end! It looks nice.

[@dtperformance256]

@Christopher Sutter thanks for watching and the comment. It took a while to get the funds for the rearend for sure. I have more time in it than I do anything else….lol. Thanks again for watching and the comment!!

[@TravisWallen-b3z]

Nice job DT!

[@dtperformance256]

@Travis Wallen THANKS!

[@burgesslane131]

Nice vid DT. I like the loop vs the bends. Just my opinion though! Especially since a spare can be used anywhere.

[@dtperformance256]

@Burgess Lane Thanks for the input! Also many thanks for the view and the comments!!

[@allencobbs4047]

Nice job I like the short lines but it’s all what you like both work fine I don’t see your axle vent anywhere

[@dtperformance256]

@allen cobbs thanks. The axle vent is there, I don’t have the vent fitting or vent tube installed yet. The Trick Chassis rearend did come with a brass barb fitting for the vent though. If you look in the video you can probably see on the passenger side where I had the vent plugged for paint. As always thanks for watching and the comment!!!!

[@allencobbs4047]

Went back and found it sorry about that

[@dtperformance256]

@allen cobbs glad you are watching!! No apologies needed.

[@pbclax1]

What size washers and nuts did you use?

[@dtperformance256]

@pbclax1 The washers and nuts for the brakes came with the kit. I am not sure what size they are, but I can get that info for you this weekend.

[@compactorcompaction6539]

Nice job DT!

[@dtperformance256]

@Compactor Compaction Thanks!!! Thanks for the comment and watching!! Much appreciated!!!