Trouble shooting tricks for a 1997 Kenmore/Coldspot/Whirlpool icemaker module

This video describes the ways to check/adjust the ice maker module on a Kenmore/Coldspot/Whirlpool refridgerator. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest!

[@datguykirt]

Once you have the cover off, measure the location of the water flow-time adjustment screw and mark that location on the cover. Drill a hole at that location large enough for your screw driver to fit through. Then after you've finished, if it needs adjustment again, you won't have to take the whole ice maker out just to adjust the water fill time. You can cover the hole with a good quality tape or a small rubber plug if you want to.

[@MrManny235]

Thank you! I have been looking at MANY videos on how to adjust the water level to increase or decrease the ice cube size as mine were too small and all videos showed the screw on the front of the module but mine wasn't there and you explained it well! 2:28 on this video showed it.

[@datguykirt]

Turn adjustment screw clockwise to reduce water fill time. Turn adjustment screw counter-clockwise to increase water fill time.

[@datguykirt]

Once you have the cover off, measure the location of the water flow-time adjustment screw and mark that location on the cover. Drill a hole at that location large enough for your screw driver to fit through. Then after you've finished, if it needs adjustment again, you won't have to take the whole ice maker out just to adjust the water fill time. You can cover the hole with a good quality tape or a small rubber plug if you want to.

[@tamifelver2561]

Hot Damn! This video is exactly what I was looking for! Sadly, I didn't come across it before pulling out the ice maker to do repairs lol So, tomorrow, I will be doing an in unit adjustment to the water level. Thanks for this awesomeness😆

[@kkutube1972]

Your the best. I replaced the whole unit did not know how to force test to see the leak. 3 hours later, my tenant tell me that it is still leaking.

[@Lsailor169699]

Thanks for watching my video and your kind comment! You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@Filofilosofo]

After several tests, everything indicated that the icemaker had no problems, but it still did not work correctly. I bought another icemaker and installed it successfully. I disarmed the failed icemaker and discovered that a gear that transmits the force of the motor to the control rotor was worn. Natural after working for more than 25 years.

[@Lsailor169699]

So glad that you found out what the problem was and shared your solution! Best, The Sailor.

[@jeffmarcum3643]

Thanks for the video. I didn't actually use the shorting/jump start method - but the info helped me identify a problem. I pulled the control module out and found that the contact on the trace for the "L" hole (where it pushes onto the stud in the unit) was burnt. Some of the copper (brass?) tabs were actually gone as well. I cleaned the trace and the stud on the maker and put it back together. Water immediately flowed into the icemaker. Not sure how long it will last though. Now the decision is whether to buy just the control module or an entire new unit. Thanks again.

[@Lsailor169699]

Thanks for watching my video and your kind comments! You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@carriesheppard5150]

I need to know if when i buy a new whole harvest clock module do i reset it or do i jus put new one in and wait

[@carriesheppard5150]

I put new one in and since I can’t find anyone telling me I need to reset it after putting a new one in I just put it in and just gonna let it sit and see if it will do on its own because I can’t find information on anybody’s video about when you put a new one in do you just put it in the icemaker and then connect everything up and let it go

[@jeffmarcum3643]

I ended up replacing the entire icemaker unit. I didnt reset anything. Just replaced and it worked

[@johnmontana18]

How can you do these tests with electricity off as you instructed in the beginning?

[@cramsey548]

Note... you can't jump the start with the power off, which was step 1 in the video at 1:05. Might help you know that with an ohm meter... Test points N-V is water valve and should read between 100 and 350 ohms. Test points L-N is the timer should read 4400 ohms. L-H is the tray heater and should read between 50 and 100 ohms. T-L is the tray thermostat and should read open with no ice and 0 with ice in the tray. Mine was frozen up from condensation after a 20 min power outage. It would not advance after shorting the T-H. I flipped the breaker off and held the ice door open for 4 mins, tapping the module lightly with a screwdriver handle, it now works.

[@Lsailor169699]

Thanks for watching my video Craig and your most useful comments! Will only help the community more! You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@lsee6145]

@cramsey-thanks for those tips..a DVOM takes the guessing away

[@datguykirt]

Turn adjustment screw clockwise to reduce water fill time. Turn adjustment screw counter-clockwise to increase water fill time.

[@MrPhizler]

I did the jumper test and the wheel did not turn. I was ready to get a new icemaker but i still was not convinced. I unscrewed to module and checked behind. The motor and gear all looked good but it may be the mechanism that turns the shaft was jammed..thus caysing the clicking sound. I gave it a few spins and reattached it. Works perfectly..saved $200.

[@Lsailor169699]

Thanks for watching my video and your great explanation! It will help others. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@eagleviewhd]

If the icemaker is making noise like it is trying to release the ice cubes, but they are stuck, it is probably a problem with the heating element. I took the control module off of the front of the ice maker, and found the pin of one end of the heating element was very dirty, and the contact where the pin mates with the control module were arced and dirty also. After I cleaned the pin and the contacts with some sandpaper the ice maker worked fine. I would recommend the contacts and the pins be checked at the first sign that the heater is not working properly. Due to the arcing the contacts on mine were damaged and even though I got it working again, i needed to order a new ice maker.

[@Lsailor169699]

Thanks for watching my video and your very helpful comments! I have found that if you raise the stop bar before the ice cubes are ejected, they will freeze in place and then you will need a hair dryer to loosen them and start a new cycle. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@Cochituatebeach]

How do I remove the smooth cover in order to expose the panel being shown? I have a Whirlpool and can't feel any clips or screws, that I can find, unless they're in behind?

[@leejuhsu]

Hi, my new ice maker makes only one batch of ice per day. Anything I can do to up the produce rate?

[@anthonymartin2412]

clean the condenser. freezer need to be -5 deg to make ice faster. and will stop making ice @ 16 deg.

[@theresabg]

I replaced my control panel. Now the icemaker does not work (although the frig is working just fine). All the advice says to turn off the icemaker and unplug the frig for 5 minutes so the icemaker can reset. My model is similar to what you are showing. There is no on/off switch on my icemaker. I popped the cover and what I am seeing is similar to what you are showing -- with the dial etc. Where is the simple on/off switch so I can reset the unit before I have to try other things. Thanks!

[@Lsailor169699]

Thanks for watching my video! There is no on/off switch and that is why it recommends turning the frig off for 5 minutes. Since that isn't working, at 2:05 in my vid, try seeing if the motor works. You could also try seeing if the icemaker plug is secure in the fridge Under the icemaker. If the motor still doesn't work, the icemaker isn't getting juice and is suspect. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@renerioux2644]

My motor turns when I jump T&H and the valve flows when I jump L&V but still not producing the ice. Any ideas?

[@whatthe2458]

Is there a way to jump a newer style one? I have a Frigidaire with a basic icemaker

[@joselcorrales1144]

I just got my new icemaker i did the jump but only do one round and then stop, to restart i have to do jump what i need to do

[@rickeykeeton71]

Alabama here too. So you had to cross the fill valve out every time to get water, or is there a fix for that icemaker? I have one now that I think the valve might be bad. Only ohms out at around 228 ohms. That being said, the water solonoid for the water dispenser only read 346 but still dispenses water. Is 500 to 1500 ohms normal reading for water inlet valves? Until recently, I always thought they were good if they only showed any continuity.

[@Lsailor169699]

Thanks for watching and roll tide! This vid might help: kzbin.info/www/bejne/l4msiWppeq5kkJY You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@melissabeck3751]

I replaced the module and the optic sensor for the door and still no ice... I tried jumping both places you suggest and neither did anything with either the original module or the new replacement one I bought off Amazon. My water line is clear and everything looks fine, just no ice. Any other thoughts?

[@Lsailor169699]

Thanks for watching my video Melissa! It sounds like you don't have power to the unit. Take the whole thing off and get a volt/ohm meter and check for 120 volts coming from the hook up point. If no voltage, you will have to follow the wires to where they hook up further down. You can also check with the unit in place (I don't prefer this method). Here is everything you need to know on checking things out: www.american-appliance.com/old_Site/service_pages/Ice_Maker/modualimdiag.htm You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@williamcrazylacyfurmage9953]

It's weird, on this Amana I'm working on, I have to jump the M and The N to get it to rotate??

[@Lsailor169699]

Thanks for watching my video! At 2:07 in the video are the holes to jump to get the motor to operate on a Kenmore ice maker. Not sure about an Amana. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@kyranlee4088]

Thanks ! ❤️I did it I got it!! 👍Water 💦

[@Lsailor169699]

Thanks for watching my video and your kind comment! You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@daniels1675]

great video. I jumped the holes for the water valve and got water. now I don't know what the problem is yet I get no water for unless I jump it

[@Lsailor169699]

Thanks for watching my video and your kind comment! The good news is that you know it is not the valve down at the bottom where it enters the fridge. Depending on how old your unit is, you may want to just replace the whole ice maker. They are not that expensive. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@daniels1675]

HEY THANKS BECAUSE IT HAS ME BAFFLED. GUESS IF I HAD A METER I COULD CHECK THE OHMS BUT I DONT. THANKS

[@Lsailor169699]

@@daniels1675 My pleasure! Hope it all works out. Best, The Sailor

[@nicholashauser6607]

I jumped the T/H holes, and saw the motor turning -- great. Immediately tried sliding the unit back in, but when I hit the black hose, water started pouring out. I quickly unplugged it, but now after I've plugged it back in, the T/H jump no longer works. Is there anything I need to do to recycle this?

[@Lsailor169699]

Thanks for watching my video! Here is everything you need to know on checking things out: www.american-appliance.com/old_Site/service_pages/Ice_Maker/modualimdiag.htm You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@TonyNapoli]

@@Lsailor169699 the link to American appliance is broke

[@jbatarse]

Thanks very nice video, i would recommend to put audio on it..... i think it will be a nice idea....

[@Lsailor169699]

Thanks for watching my video and your kind comment! I make my videos for world wide consumption and with my format other countries can translate into their language. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@Filofilosofo]

In minute 2.10 you say jump two holes for motor, but those two holes are: one for thermostat and the other fo mold heater. Are you sure you are not going to burn or cause damage to the unit, for the people that think you are knowing wath you said.?

[@Lsailor169699]

Thanks for watching my video! You should jump "T" and "H" holes to make it cycle. If you don't trust me, there are many other videos that show the same thing. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscibe for the latest! Best, The Sailor.

[@Filofilosofo]

@@Lsailor169699 thank you.

[@trevieneofficer3893]

Have question

[@trevieneofficer3893]

What if the rotator stuck on L what the problem its going back and forth

[@fabianruiz5948]

​@@Lsailor169699 You're right I checked the connections and they are for the motor. Could you help me out? I checked the motor and I got resistance. I did the two jumpers but nether I have water running or motor turning. I checked all the lines in the module there's nothing burned. Last thing I did turned the small plastique screw more than it should, could be this the problem? thanks for your help.

[@narendrapatel1123]

Nice

[@Lsailor169699]

Thanks for watching my video and your kind comment! You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@dh-in8qr]

What if the ice is hollow inside?

[@Lsailor169699]

Thanks for watching my video! New one on me! Did a Google search and it is amazing what the causes could be! I hope one works for you. removeandreplace.com/2015/10/30/refrigerator-freezer-ice-maker-makes-hollow-ice-cubes-how-to-fix/#:~:text=Hollow%20ice%20cubes%20can%20be,to%20make%20the%20ice%20cubes. You may like my other videos. Just type Lsailor1 in the KZbin search bar. Like them? Subscribe for the latest! Best, The Sailor.

[@dh-in8qr]

@@Lsailor169699 Thanks for the quick reply and info. I'll let you know what I find out.

[@Lsailor169699]

@@dh-in8qr Pleasure! Best, The Sailor.