Thank you. Thank you. Thank you. My CPAP stopped in the middle of the night last night. So did my lamp and my adjustable bed. I pushed the surge protector and the lamp and bed came back on but not the cpap. I watched your demonstration for about a minute thirty. When you said the plug has to be really plugged in hard, I thought oh please let it be that easy. It was. My cord from the wall to the transformer was plugged in but not really "plugged in hard". It's working. And now I'm going to take a nap. You saved this old lady.
@smileysun9212 Жыл бұрын
You are a life saver. ❤ I was panicking that my CPAP wasn’t blowing hard enough & I couldn’t breathe. The tank came loose.
@ronmay37142 жыл бұрын
One guy wrote that these have a tiny computer inside and might need to be rebooted like one. Unplug it from wall for a few minutes and plug back in. Viola! It worked for me. For those of you getting nasty stuff in your tank you should rinse it daily and once a week soak the whole tank in a mixture of white vinegar and water for 30 minutes to avoid mold. I won't it using approximately 2 cups vinegar and Three cups water. Make sure the whole tank is covered. Works like a charm. I clean my hoses and mask weekly using dawn dish soap and let air dry. Never use bleach! Also only use distilled water in the tank. Hope this helps!
@johnbethel97252 жыл бұрын
Question, just recently the machine is loud with air moving, my wife says it goes along with my breathing pattern and sounds like a ventilator at times. It will wake us up. I have cleaned everything, reattached everything but finally put the machine under the bed. Any ideas?
@ms.c3 Жыл бұрын
Thank you so much! 🙏🏽 I followed your trouble shoot. Slept one night without machine. I couldn’t sleep. Next day I did go through and finally got it to work. 😉
@PNH-sf4jz Жыл бұрын
A clear and pleasant presentation of possible difficulties and problems. At the same time, a very good presentation of the basics involved in setting up the CPAP machine - Resmed Autoset 10 in this case. Thank you very much, PNH.
@749Giovanni Жыл бұрын
And some nice looking tatas 😝
@d4niel3032 жыл бұрын
3:30 The most important thing for me in this video. This white connector. Thanks!!
@d4niel3032 жыл бұрын
I didnt know that this part can be unplugged. This "quick disconnect" has not been described anywhere in the manual. I have 2 different tube, one with warm system and without.. I spend 1h to find how answer how to switch this tube and I failed.. This video show me that "things" that I cannot find answer...
@oldandy16452 жыл бұрын
Wow! Those are quite nice!!
@pakalikahickey5807 Жыл бұрын
You know I have watched this video three times and every time it has fixed another of my problems, this time was the part about the main hose hooking to any of the masks. I was given a new mask and couldn't get it to work and now I realized I left the quick disconnect part in the hose of the old mask, it all fits fine now, I was convinced I needed a new hose. THANKS
@waynemartin35112 жыл бұрын
Andrea, thank you. I hope you have more videos for the AirSense 10 AutoSet.
@Jrg4life Жыл бұрын
Thank you soooo much it was stressing me out not being able to figure out where the leak was at
@marywitbeck92013 жыл бұрын
Thanks so much. The electricity went out 3 hours ago, and I've been trying everything to get it back to work. After watching your video, I wss able to disconnect and reconnect the power pack. I never noticed the green light on it. Now for a good night's sleep, for a few more hours.
@royestrada7772 жыл бұрын
The best part for me was learning about the “hose disconnect.” Sometimes in the middle of the night I want to maybe grab something on the other side of the room but the hose doesn’t reach that far so I have to take my mask off while I’m half asleep! Not no more 😀
@choney81253 жыл бұрын
Hi having trouble with whining noise in area where clean filter is. Any advice? Thanks
@lefefe783 жыл бұрын
How do I get the signal to work because it has that circle and slash sign over the signal bars
@jigginjohnson28933 жыл бұрын
Man, I wish she showed me how to set up my cpap!!
@conniecrespino29562 жыл бұрын
First one that explained air coming out. Thank you. Thought it was leak.
@MC553113 жыл бұрын
Video was very helpful. Thanks for your insight on the exhalation port. I was wondering why air was leaking out of the connector.
@mattlau954 ай бұрын
Thanks for the help with this, for me it was the water tank. It looked completely pushed in but after seeing your video I tried it and it fixed it. I was thinking I had a leaking mask or something
@USAMedicalSupply3 жыл бұрын
Great video Andrea! Keep up the great work and keep growing this channel.
@markcottierkw950 Жыл бұрын
Damn,, Nice puppies 😃😄👍👍
@jimmydcricket58933 жыл бұрын
Great instructions with a couple of high lights that made it great.
@oldtimer994 күн бұрын
High pitch noise when I inhale. All connections checked ok. It seems that it comes from the unit controlling the inflow. Suggestions?
@papajim19743 ай бұрын
Where do you attach bacterial filter on rested aircurve 10s with humidifier? Thx
@craigpinto35772 жыл бұрын
So I am having an issue that my machine is turning off on its own in the middle of the night. I have rez med 1O the error message I get is tubing is blocked. When I check the tubbing nothing is blocking it. What then can be the issue
@suzannebihari48682 ай бұрын
Just watch the video on an automatic off function. Call ResMed..... Of course I was in Florida in the middle of a hurricane last night
@ajfreeman56 Жыл бұрын
My unit won’t turn on. The power bank isn’t solid green. It is flashing green. It is plugged into a good outlet that many other things work on. What is the issue?
@tundramike35226 күн бұрын
I can't get my leak level under 65 and I replaced the mask, pillow, tubing, humidifier chamber, and headgear to no avail. I have had it for 5 years and know how ti use it. My usual leak level is 27 until about a month ago. Very frustrated. Any suggestions?
@BradBowcutt-sq6jy7 ай бұрын
Hello. Your videos are so helpful. I have an issue with my philips dreamstation 10. I use a ResMed Quattro FX medium. When I exhale, the mask is making a "thumping" sound. I suspect it has something to do with with the pressure setting while I exhale. I cannot figure out how to confirm or adjust this. As I start to relax, I find I will exhale a little more relaxed and the thumping sound from the mask either goes away or becomes much softer. It is so annoying. Do you have suggestions for me?
@shirleya45102 жыл бұрын
I JUST fixed it, thanks to you 👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽 ❤️❤️❤️
@rudedogg8052 жыл бұрын
Don't you just love KZbin 👍
@svendholme36273 жыл бұрын
At the beginning of the video problems with "no power" were mentioned, in addition to checking for plugs not being inserted in all the way or a wall switch, also check if the outlet the CPAP power supply is plugged into is a GFCI outlet (ground fault circuit interrupter) it may have tripped. Be aware that a GFCI outlet may control several outlets in a room and may not be the one your CPAP power supply is plugged into.
@Gman-qm6bv Жыл бұрын
Discuss the engineering problem with the Airsense 10 water chamber box which sometimes leaks around the middle edge due to the silicon seal being worn and how we need to re-silicone the middle rim all the way around to stop this leakage. Discuss how the Airsense 10 in automatic mode will sometimes start blowing air after you take the mask off and leave the bedroom. I had to put mine in the manual mode to stop this problem. It is over sensitive in the automatic mode. Resmed has moved on to the Airsense 11.
@PNH-sf4jz Жыл бұрын
Having had this diffuculty with my previous machine, I can appreciate the concern. To me, the problem with the leaking water chamber and a few other minor problems was a sign that i needed a replacement machine, which I recently purchased. The other one will be kept for reserve, with the problems fixed as far as I am able. PNH
@lindagraff24843 жыл бұрын
Good issue solving. But how do I fix it, when it's just blowing too hard and it's loud.....
@raymondjr.10802 жыл бұрын
Thank you. Are the Phillips and Resmeds masks compatible. Do they fit interchangeably?
@myronachtman43047 ай бұрын
What is the typical life expectancy of the ResMed AirSense 10 power supply?
@rodneywalsh6593 Жыл бұрын
What does "Settings memory error" mean when you plug in a heated tube?
@christopherdaum43967 ай бұрын
Please help if you can; my rested air sense 10 has started to have a constant humming noise all night, and it changes some when I breath. It is constant. Thanks if you can help.
@burns322 жыл бұрын
03:55 anyone else catch that 😎😎
@ZacharyCheramie-u1d11 ай бұрын
What about a thumping sound from the valve in the elbow coming out of the mask? Happens on the exhale randomly, how do I stop that from happening?
@EverythingsConnected. Жыл бұрын
Thank you for the share. Question: what is nasle mask and headgear in this video and where can I get it? Is it a medium or large and is it an N20?
@mrsangelleah1981 Жыл бұрын
Please help!!! 😰😰😰 how do i change the ramp setting to auto or off? I have asthma and my dr has it set to 5 minutes and i feel like im suffocating. It stresses me out. Not good for sleep. I dont have another appt for 3 months and they are impossible to get ahold of. I even tried holding down my options and my sleep view to access special menu but that doesnt work either. Its de-selected. Please help.
@kekee3014 Жыл бұрын
I need help now
@lykemikeee9 ай бұрын
Mine just randomly started blowing out air loudly, similar to when her water chamber wasn’t in all the way. I don’t get that warning message though.
@kalelklenk2 жыл бұрын
So I had an accident my bipap machine was in my van and it started raining the water was entering in the van and my bipap machine got soaked in the water and now doesn't turn on,what should I do?.
@loutrigg30163 жыл бұрын
How to install new strap
@Madronaxyz Жыл бұрын
How do I remove the water chamber when it's stuck?
@pb4life4352 жыл бұрын
I need a new HotPlate for my heater to work. I'm really handy. And good at things like this. I need the Heater with fuse and Di not know where to find one. Could you Help me Please. It is the same Machine that's in your video.
@chiffydragon2 жыл бұрын
Thanks. The breakaway tube from my last mask was indeed still stuck in there, whoops. Really appreciate the video.
@teresaboyer57073 жыл бұрын
I have an issue with debris ending up in my water chamber. I’ve never used anything but distilled water, and I have a so clean. In theory. Otho got could get into the system. But about every 5-7 daysI find things like clumps of mucus (?) or slime(?) happily floating around in the water chamber. Or little pieces of whitish stuff. Where is this coming from and how do I stop it?
@73leo733 жыл бұрын
Dump your water and use fresh distilled every day. I also put 2 tablespoons of hydrogen peroxide in my tank a couple of times a week and run it with the peroxide over night with no harm. It seems to help boost my breathing/sleep for me and I have been doing this for years.
@deekay30643 жыл бұрын
Do you dump and refill daily? If not, you absolutely must. Also, you have to clean the tube once a week...bestnto soak it in a bath of white vinegar and water then rinse thoroughly and hang to dry.
@grahambarnett70183 жыл бұрын
Fix Resmed airsense10
@vkhan54312 жыл бұрын
Same here.
@styx62 Жыл бұрын
I got the error message for water chamber now the machine won’t turn back on after I put chamber in all the way
@peggy6553 Жыл бұрын
What if machine stops working at the end of ramp time
@WhocaresWhy443 жыл бұрын
Got the light to the corner of the box .Check. Push the cord all the way in no light to switch. Menu Box unlit. If I pull the cord out slightly then the power switch flashes green but no joy. Defective Cord? Switch? Or Unit? Tried 4 deep nasal breaths. Nothing.
@nortenoald70463 жыл бұрын
Same problem
@nortenoald70463 жыл бұрын
Brand new machine with same problem
@citybellsincountry3 жыл бұрын
Brand new machine, same problem
@ROROSMACHINE2 жыл бұрын
I was having trouble with my Airsense 10, the unit would switch off intermittently. This occurred a few times, then it would not power up at all. After a good deal of frustration I accidentally smashed it with a giant sledgehammer....
@margaretbrunston68422 жыл бұрын
My machine has been broken since almost a month. Can’t get LINCARE to believe me. It came on in the office but when I got it home it stopped AGAIN!!
@LiveinLakeForest Жыл бұрын
had hoped to find answer as to why air won't shut off if mask is removed - husband's system shuts air off after a few seconds - why not mine?
@CWBush732 жыл бұрын
I lost my Wi-Fi connection to the machine
@WhocaresWhy443 жыл бұрын
The tutorial is great. The Phillips power cord is not compatible. Labor issues with the manufacturer?
@carolbradley19412 жыл бұрын
I have a "mask off" reading from Resmed, even when the mask is on and tightened down. What should I do next?
@chazzthaspazz4475 Жыл бұрын
jusy got the Tubing blocked, check your tubing error
@mollycartercalhoun5913 жыл бұрын
You gave a good report made a good video but stopped did not continue info regarding power card, My power cord is working, the green light is on but when I plug power cord into AirSense 10, green light on machine trys to appear but disappears and Resmid 10 will not power up. What can I do, this is fairly nnew but out of warrenty, Some one please help me. Medicare will not purchase a new C pap machine for me at this time, due to this one being so new
@dragonfruitopia2 жыл бұрын
Does the ResMed AirSense11 come with the ClimaAir grey (heated) tubing in the box, as part of the machine? (or it requires a separate purchase?) Thanks.
@judyquimby76283 жыл бұрын
Having trouble the cpap machine transmitting to my computer for nightly info? Machine is working fine at night and also went to therapist and they checked machine working fine.Resmed my air says to contact supplier but they say they only supply equipment. how can I get help have sent emails to resmed but no reply. Thanks for any info.
@petergreenham72353 жыл бұрын
During the night my exhalation ports seem to get blocked and I need to clear them , is there anything I can do to stop it happening
@armadillotoe2 жыл бұрын
If the water chamber is in far enough for the machine to work but not fully seated you may get higher pressure than you expect. At least I did on my machine.
@suzannebihari48682 ай бұрын
What? Why would that be? I sure want to be done with this machine. Imagine the plastics we are breathing in
@sportshistorybuff3194 ай бұрын
For two nights now, I have been unable to use my Resmed. I tap the start button and it shows the air pressure rising, as usual. Then, when it hits 8.0, it shuts off, no air coming into my mask. What could explain this?
@shaylenoir810312 күн бұрын
Same
@glorytogodbindandrebukee-ls9ub Жыл бұрын
Thanks i didn’t know how disconnected during night🙏
@dennisdullewe7114 Жыл бұрын
How to register the unit
@xchuckwagon61932 жыл бұрын
what is the little circular bulb on the upper right from the front screen on the machine?
@PNH-sf4jz Жыл бұрын
The only item that I believe that you may be referring to is the "rotate and select dial and button" to the right of the display screen.
@pauletteplatero74432 жыл бұрын
Does anyone else have a hard time removing the water chamber? If so how do you remedy this problem. Helpful comments much appreciated
@shepatown Жыл бұрын
My problem has been the total minutes not showing up after taking a nap. The same thing is happening with my new RESMED AIRSENSE 11. In other words, it shows some minutes slept, but not all minutes slept. (ie: 36 minutes showed after sleeping 1 and 1/2 hours.)
@heatherleighedenfield6558d3 ай бұрын
Mine is throwing a 75 error code and it’s never been used 😢
@wakethebarbarian45773 ай бұрын
My CPAP is blowing way too hard. I've tried numerous things. Unpluggled the power chord, removed the water chamber, etc. It just keeps blowing extremely hard.
@charlotteforrester3118 Жыл бұрын
Mine quit working for some reason . I followed her instructions and everything was fine but it still didn’t work. Reading the comments, someone posted that they unplugged the unit from the wall for a few seconds and theirs started working after it reset. So I did mine, unplugging for about 5 seconds, and it reset and began working!
@cricketpremi37222 жыл бұрын
how to problem solve airways blocked alarm ??
@bobmurphy1783 жыл бұрын
How does one solve the problem “ high leak detected connect your tubing” when tube is connected? Thank you Bob M
@shaylenoir810312 күн бұрын
My machine will not work but did girgle earlier.
@neilyaremchuk6798 Жыл бұрын
Chords checked and getting power. Still a black screen.
@madcap47764 Жыл бұрын
Recently my tube has been working correctly and I wake up with water in the mask. How can I fix that?
@-Scraggyanne-10 ай бұрын
Change the humidifier level and that should solve your issue
@johuraholy9913 жыл бұрын
I need to know how to take of the black lid before placing the water tank in ?
@ralwoe3 жыл бұрын
Well there are these things called fingers that should be attached to your hands. Try using them to grip the cover and remove.
@johuraholy9913 жыл бұрын
@@ralwoe unnecessary.
@edattard34732 жыл бұрын
how do you fix error 010
@jimquantic2 жыл бұрын
Thanks you, but how do I adjust the pressure setting or the stroke (number of pumps per minute), etc? I don't see that on the menu?
@-Scraggyanne-10 ай бұрын
That's in the clinical menu and has to be accessed by pressing the round button and 4he home button at the same time. Hope that helps
@jimquantic10 ай бұрын
@@-Scraggyanne- Yes it does help--and thanks for taking the time to help me out
@-Scraggyanne-9 ай бұрын
@@jimquantic glad to be able to help 🙂
@jasongooden9172 жыл бұрын
The problem I'm having is my water chamber is stuck, and no it's not dirty, I clean it regularly. It's almost as if its Krazy glued in place.
@TheMommyofAlyssa2 жыл бұрын
Did you figure out how to fix it? Mine is doing the same thing. I found a little plastic piece in there after I finally got it out. It came out easily after that but then the next day it is doing it again and I absolutely can't get it out.
@OPSteel973 жыл бұрын
Can I use the machine without the humidifier? Can I take the water chamber off and close the side?
@sogno2me3 жыл бұрын
Of course you can. There is and add-on cap you buy separately and it clips instead of the water chamber making the size of the machine smaller (I.e. good for travel). I bought it when I purchased the machine but truthfully hardly used it as I find I need the humidifier.
@mybobbleheads2 жыл бұрын
My heated hose is not working, I bought a second heated hose and still no go. Took the machine apart and found the ribbon cable inside the main unit where the hose is connected is torn in half. Trying to source a ribbon cable as it's just a cheap part but I am getting no response from Resmed. Any idea where I might get a part? Shipping from Canada to the US to replace a part that takes me 10 minutes to replace myself is out of the question as it would cost me hundreds of dollars for a $20 part.. I have no problem paying for the part and shipping to do it myself it there are any users with a dead unit. Thanks
@quamiller50933 жыл бұрын
Mine still is saying that will the chamber in. Very frustrating
@bklynny643 жыл бұрын
Let me see if I get a response. My water tank has gotten hard to remove to fill what can I do?
@ronmay37142 жыл бұрын
Took me some time to get tank to remove easily. Try pinching it on both sides a pull straight out. I punch mine towards middle section.
@davej7458 Жыл бұрын
The water tank on my machine seems to remove quite easily if I put my thumb on the white plastic spot on the top of the tank and fingers underneath the bottom of the tank squeeze gently and just pull.
@nathanieljacobs31513 жыл бұрын
what should I do if I found mold at the bottom of the water reservoir?
@ralwoe3 жыл бұрын
Clean it and stop using swamp water.
@TheMommyofAlyssa2 жыл бұрын
Clean it really good with vinegar and clean weekly with vinegar and blue dawn dish detergent. Use Distilled water only.
@annettes965 Жыл бұрын
Got it right off, my kitty must have unplugged it in his night ventures lol thank you ❤
@alisyedzain13 жыл бұрын
Humidifier has stopped working on my Cpap Please advise as how to fix the problem?
@ralwoe3 жыл бұрын
Try turning it on.
@insanity6105 Жыл бұрын
Wow! Nice tips
@michaelharrington59142 жыл бұрын
My machine won't turn on?
@grandmajane2593 Жыл бұрын
Good presentation, but I wish you had addressed the problem of the tank running out of water in the middle of the night.
@Hamkloud51502 жыл бұрын
My machines not loading the data
@hueroski2 жыл бұрын
Nice rack. Thanks.
@archiepound41203 жыл бұрын
My res med cpap smart start is not working. Can not turn on. Smart start not lit up
@sogno2me3 жыл бұрын
Have you gone into clinician mode to change it? You should be able to.
@raymondfraley Жыл бұрын
"Hey Baby"
@glorytogodbindandrebukee-ls9ub Жыл бұрын
Mine won’t charge
@pamelakhalifa3 жыл бұрын
mine is new and it leaks...leaks all the water out only when turned on
@ralwoe3 жыл бұрын
Does it have a hole in it?
@pj611142 жыл бұрын
Need more on how humidity is controlled auto / vs manual settings.
@jbeachboy100 Жыл бұрын
I put too much water above max line.
@13223lazyglen Жыл бұрын
Why not show the "exhalation port?" I don't know what you mean about CO2.