Bmw 120d N47 engine, flywheel and clutch replacement! How to!

[@thevellafamily6442]

What type of gearbox do you have on it zf gearbox or getteg gearbox?

[@dennizeen]

Why is there a gap between the flywheel and start motor/engine on my e91 N47? If I lay under the tranny I can see the flywheel. It feels like something should be inbetween this empty space

[@dennizeen]

@@88CBAUGH Sorry for confusion. Ik how the starter works and all, but there is a gap/hole where i can look at the flywheel while being under the oil pan without dismantling anything from the car. It kinda looks like a half moon.

[@vincenzotrasmundi7617]

Can you make a list of the tools that you used to do the job? Like the 14mm key, Hex 6

[@daviddorado5632]

Mine shakes when starting from 1st gear, mostly when hot but not always. Any idea what it is?? Thanks

[@RobinBengtsson-v1d]

Hi. What torque settings are there for the flywheel and pressure plate?☺️👍

[@ryzenx-no1bl]

what can it be if the car makes noise when the clutch is in middle ?

[@WarpDriveM]

Usually is the throw bearing

[@disturbator]

Do you recomend removing CDV valve?

[@marianov4017]

What clutch Luk valeo ?

[@artiislamaj4214]

After how many kms did you change it. Or did you notice any type symptoms?

[@sjt237]

Where are you located? How much do you charge to do this job

[@alexflux1465]

Approximately how long time does it take to change it??

[@WarpDriveM]

If you don't have a lift aproximativ 7 hours, with lift 5 hours

[@moal1061]

Nice work 😊 what do u think of converting from Dualmass to single mass flywheel for N47 motors?

[@WarpDriveM]

Don't do it....🤷‍♂️

[@acidrain55]

How did she drive after?

[@WarpDriveM]

Perfect shifts, no more crazy vibration, pretty normal I might say.

[@acidrain55]

@@WarpDriveM top man well done please to hear it. 👍

[@artherj327]

Very informative, thank you

[@stfu6397]

legend

[@Bas20005]

Muss Partikel Filter auch ausbauen???

[@WarpDriveM]

Nein

[@Bas20005]

@@WarpDriveM ich habe Motorlager links und Rechts neu gemacht. Vibrationen sind nach wie vor da. Jetzt du bist mein Retter. Ich Versuche mein Glück. Die Teile habe ich schon gekauft alles zusammen 380€ .

[@WarpDriveM]

Ich hoffe klappt gut! 380€ ist top preis, viel spaß

[@Bas20005]

@@WarpDriveMdanke 👍

[@GreatScottByJoe]

Hi Liked and subbed, do you know is the clutch a wet or dry clutch?

[@WarpDriveM]

This is a "normal" clutch a dry clutch. The wet clutch is exactly what the name says...wet clutch (in fluid, oil)

[@MecaniculTau]

Perfect LIKE

[@GeorgeAusters]

The pressure plate screws should be replaced!

[@WarpDriveM]

As per the repair manual, you have to replace all the time everything but because these are not aluminum bolts or stretch bolts or have a ° degree torq I use them every time when the kit doesn't have them and in the last 12 years I never had any problem 😉

[@karloarbanas8494]

I'm ok with everything but man, disconecting the drive shaft is pointless if it was a drive shaft problem car would shake while driving on certain rpm ,drive shaft is not spinning while the car is stationary

[@maggiemoutlaneng8877]

Automatic

[@WarpDriveM]

Nope, it's for a manual car 🚗 😅

[@cosminpetcu3286]

Hello.i replaced my clutch and new one has came without that pice in midlle that you removed with allem key 14mm.it is normal?please give me your email address,i will send picture.i need some advise. Thank you

[@WarpDriveM]

Hey, there are different parts and sometimes is normal to be without the plate. It will tension itself when you tight the bolts. You can contact me @warpdrivem on social media or [e-mail]