WATCH ME REMOVE THIS ENGINE! Honda S2000 Engine Replacement!

S2000 Engine Removal. We removed this engine out of this AP1 S2K because of spun rod bearings as well as a stretched timing chain. After removing the engine we also noticed a completely worn clutch along with flywheel and pressure plate. We will be going through the new engine and will upgrade/replace a lot of the maintenance items before it goes back in. Subscribe and turn on post notifications so you can see our next video where you will see how we sourced the new engine!
Part 2: • NEW ENGINE and it stil...
Support my channel by becoming a member using this link: / @shoplifetv
My Amazon Store: www.amazon.com/shop/shoplifetv
Buy My Merchandise: www.shoplifetv.com
Ask me a question: www.shoplifetv.com
Request a Shop Appointment: www.shoplifetv.com
Instagram: @ShopLifeTV
/ shoplifetv
My vlog channel: / shoplifevlogs
KZbin Business Inquires: Email me [e-mail]
Music:
Track: I Am OK - Vishmak [Audio Library Release]
Music provided by Audio Library Plus
Watch: • I Am OK - Vishmak | Fr...
Free Download / Stream: alplus.io/i-am-ok
Himalayas by Mona Wonderlick / monawonderlick
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/_himalayas
Music promoted by Audio Library • Himalayas - Mona Wonde...
Artist: Cheel | Track: Anywhen You Say
Disclaimer: Some links will contain affiliate links. Due to factors beyond the control of ShopLifeTV, I cannot guarantee against improper use or unauthorized modifications of this information. ShopLifeTV assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ShopLifeTV recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ShopLifeTV, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ShopLifeTV.

[@patricklilly2520]

This guy has MAD SKILLS I love to watch him.

[@razorrich]

Glad to see you fixing it right! Geez, that clutch appears either abused and/ or inferior parts with subpar installation. Keep up the great work!

[@ShopLifeTV]

The owner had the clutch replaced less than a year ago, so there should have been less than 10k miles on it. I'm assuming the shop didn't replace it at all. Thanks!

[@ExclusiveAutoClub]

I’ve been waiting for an upload!! Thanks!!

[@ShopLifeTV]

Haha thanks man! Currently working on projects that are taking longer to film than anticipated

[@ExclusiveAutoClub]

@@ShopLifeTV looking forward to seeing them!

[@cidfacetious3722]

As an old man mechanic, let me give you whippersnappers some advice always keep at least 5 to 10 10 and 8mm sockets those things have legs and will start their journey home if you do not keep them locked up

[@fabien1446]

Love y'all. Great to see you're making more content and congrats on 100k + subs. Y'all deserve it.🤙

[@chrisjay555]

Great video. Awesome work! Hope to do this myself one day.......just need a garage like that.

[@basithph8958]

Good to see the S2000 back! Can’t wait to see it back on the road!

[@ShopLifeTV]

Thanks and same here!

[@ccthao]

do all you tube people talk with their hands ? the hand motion is on another level

[@kouroshtashvishi5031]

This new type of filming is extremely good really enjoy it keep it up 👍

[@ShopLifeTV]

Glad you are enjoying it! It takes longer to film and edit, but we are trying to take all of our content to the next level!

[@williams8891]

Am glad you have introduced different types of cars. 👍🏾

[@ShopLifeTV]

We plan on continuing to do so, along with different BMW content as well!

[@mcgyverb1664]

It’s amazing how you know where to put back everything with its rightful screws.

[@ShopLifeTV]

Lol I usually have good recollection, but sometimes I will label them or even organize them in bags

[@mcgyverb1664]

@@ShopLifeTV good to know, I’ve been way your channel for some time now, so I know you have years of experience, but it’s still awesome to see you pull apart any model vehicle, and put it back together, it’s a like a crossword puzzle, and you just walked through it like nothing.

[@mcgyverb1664]

@@ShopLifeTV watching your channel*

[@cidfacetious3722]

I’ve been a mechanic for almost 20 years and keeping track of bolt is the hardest part of the job😂

[@romeyrome3219]

I need your advice plz help I have a 2006 325i and My heater would turn on and off but not blow hot air I contacted BMW just to see if there was any recalls amd there was just on the wiring harnesse underneath the dashboard I had it fixed and now my heater does not turn on whatsoever so I replaced the blower motor fist cuz bmw told me it was going out cuz how going off and on It was doing the same thing after replacing the blower motor turning on and off I replaced the resistor yesterday with a brand new one i bought from them. now it won't turn on at all im just getting a little humming noise like it's trying to click over that's it but I'm getting a cod saying Junction Box will this control the heater??

[@kylenaidoo1082]

Hi bro, could you make a video on how to replace the shift rod seal and then transmission output shaft seal on a manual transmission. Great work by the way, keep up the good work.

[@spx9164]

Sir I need help, my honda s2k engine swap is doing the mechanic, old engine had 1 cam sensor and new has 2 cam sensors.. mechanic is using old computer.. is that a problem? New engine has computer .. he can’t use old computer? is that correct? please advise

[@xr500t]

That 10mm socket is resting DEEP in a BMW far far away......my life's story!

[@ShopLifeTV]

Lol no kidding

[@madda_joe]

Hi guys, how long did it take to do what you covered in this video please?

[@user-ml2tp8no6m]

Respect from my car fix channel

[@richardjohnson9702]

My boy looking like he been hitting the gym!@!

[@d_u__v_e_t7137]

I NEED HELP! I have a problem with my e46 320i m54. i bought an e46 as my first car the car had the problem that it overheated quickly and it boiled. so I spent many hours flattening the cylinder head and replacing the cylinder head gasket. it did not work i started it and the same problem persisted. what should I do? what is the problem?

[@d_u__v_e_t7137]

@THE FBI i got the head machined.

[@d_u__v_e_t7137]

@THE FBI i understand that you missunderstand that my eng is not that good. I dont know what cause the overheat i got it with the problem . Yes you maybe right it can be pluggd or the termostat. How do i fix the pluggd house. But i have replaced the waterpump. Thanks for the help btw😁

[@ayodejiibrahimba5873]

I want to be your student 🙏 that's my dream job thanks for this lesson

[@mrnajee1]

Jason, is that the best way, dropping the whole cradle?

[@ShopLifeTV]

With a lift, this is definitely the best way. It's possible to remove the engine from the top and support the trans somehow, but it would be a pain to remove both the engine and trans from the top. I'm sure it's doable just not as efficient

[@legitangel9318]

I want to learn 🥺

[@cobrarsz1]

I was wondering what had happened to the s2000

[@ShopLifeTV]

We were just waiting on sourcing the engine and then getting it back into the shop!

[@Nico_335i_DCT]

Hi brother and sister. How is this possible? That clutch looks like one that has 100k on it..... Hopefully, the owner didn't get ripped off. Dutch regards, Nico.

[@khanbadsha9524]

💗💗💗💗

[@jamalhussain9162]

No offence mate but a lot of what I believe is reverb on the video with the audio

[@statusquoreject]

Ha I feel like Germans can never get it right... I'd much rather work on my S2K than my AMG. The thing about japanese plastic panel clips is they don't strip or rust like German bolts.

[@houseofno]

Is that the only fix for spun rod bearings is an engine replacement? Seems like an overkill solution for a spun rod bearing. Normally that's an engine rebuild, not a replacement. Just curious. Shout out to my favorite "next song" heckler Selena.

[@ShopLifeTV]

Unfortunately for the f20 engines their rebuild success rate isn't that high. And there was already quite a bit of internal damage due to the bearing material. It is definitely cheaper and more reliable to replace with a used engine. If the owner of the car wanted to spend a good amount of money and do some performance upgrades then a rebuild might have been an option.

[@profuse007]

bro, Milwaukee for noobs. go w/ Ryobi!!

[@ShopLifeTV]

I feel like ryobi and ridgid are on a similar level, I've played around with some milwaukee tools and they seem to be of good quality and power!

[@Auhbseluhte]

how you stay so skinny fit bro, im sitting here watching videos fat as a rice house... =/

[@TedSchoenling]

whoever drives that car can't drive stick. Get them an automatic.

[@ShopLifeTV]

I'm pretty sure the previous shop didn't swap the clutch out, which is why it is this bad